• Journal of Electrochemical Science and Technology
• /
• 제13권4호
• /
• pp.462-471
• /
• 2022

In this study, the electrochemical impedance characteristics of CO₂/H₂O co-reduction to produce CO/H₂ syngas were investigated in a low-temperature single cell. The effect of the operating conditions on the single-cell performance was evaluated at different feed concentrations and cell voltages, and the corresponding electrochemical impedance spectroscopy (EIS) data were collected and analyzed. The Nyquist plots exhibited two semicircles with separated characteristic frequencies of approximately 1 kHz and tens of Hz. The high-frequency semicircles, which depend only on the catholyte concentration, could be correlated to the charge transfer processes in competitive CO₂ reduction and hydrogen evolution reactions at the cathodes. The EIS characteristics of the CO₂/H₂O co-reduction single cell could be explained by the equivalent circuit suggested in this study. In this circuit, the cathodic mass transfer and anodic charge transfer processes are collectively represented by a parallel combination of resistance and a constant phase element to show low-frequency semicircles. Through nonlinear fitting using the equivalent circuit, the parameters for each electrochemical element, such as polarization resistances for high- and low-frequency processes, could be quantified as functions of feed concentration and cell voltage.

• 한국응용과학기술학회지
• /
• 제40권1호
• /
• pp.179-187
• /
• 2023

바이오물질을 포함하는 나노발전기는 무공해 에너지원이며 생분해성 전자폐기물이라는 점에서 친환경적인 전자소자이다. 특히 바이오 물질이 바이오폐기물로부터 추출될 수 있다면 바이오폐기물의 양도 줄어들 것이다. 본 연구에서는 포유동물의 피부에 존재하는 동물성 콜라겐을 이용하여 마찰전기 나노발전기를 제작하였고 그 특성평가를 진행하였다. 마찰전기 나노발전기의 전기적 양극층은 회전 도포방법을 이용하여 콜라겐 막을 형성하여 구성하였으며, 주사전자현미경으로 막이 다공성임을 확인하였다. 제작한 마찰전기 나노발전기는 주기적인 기계적 운동에 의해 3 Hz에서 7 V부터 5 Hz에서 15 V의 개방전압과 5 Hz에서 3.8 ㎂의 단락전류를 보였다. 결론적으로, 콜라겐 함유 마찰전기 나노발전기는 센서와 같은 저전력 구동 장치의 전원이 될 수 있으며 전자 폐기물 감소에도 유용할 것으로 기대된다.

• Journal of Animal Science and Technology
• /
• 제65권1호
• /
• pp.258-270
• /
• 2023

Climate change has worsened droughts and floods, and created conditions more likely to lead to pathogen contamination of surface water and groundwater. Thus, there is a growing need to disinfect livestock water. Ultraviolet (UV) irradiation is widely accepted as an appropriate method for disinfecting livestock water, as it does not produce hazardous chemical compounds and kills pathogens. However, UV-based disinfection inevitably consumes electricity, so it is necessary to improve UV disinfection effectiveness. Aluminum-based reflective nanolens arrays that enhanced the effectiveness of a continuous-flow UV water disinfection system were developed using electrochemical and chemical processes, including electropolishing and two-step anodization. A continuous UV disinfection system was custom designed and the parts were produced using a three-dimensional printer. Electropolished aluminum was anodized at 40 and 80 V in 0.3 M oxalic acid, at 120 and 160 V in 1.0 M phosphoric acid, and at 200 and 240 V in 1.5 M citric acid. The average nanolens diameters (D) of the aluminum-based reflective nanolens arrays prepared using 40, 80, 120, 160, 200, and 240 V anodization were 95.44, 160.98, 226.64, 309.90, 296.32, and 339.68 nm, respectively. Simple UV reflection behind irradiated water disinfected Escherichia coli O157:H7 in water more than did the non-reflective control. UV reflection and focusing behind irradiated water using an aluminum-based reflective nanolens array disinfected E. coli O157:H7 more than did simple UV reflection. Such enhancement of the UV disinfection effectiveness was significantly effective when a nanolens array with D 226.64 nm, close to the wavelength of the irradiated UV (254 nm), was used.

• 한국표면공학회지
• /
• 제56권2호
• /
• pp.137-146
• /
• 2023

Nanosized TiO₂ has been widely investigated in photoelectrochemical or photocatalytic applications due to their intrinsic properties such as suitable band position, high photocorrosion resistance, and surface area. In this study, to achieve the high efficiency in photoelectrochemical and photocatalytic performance, TiO₂ nanotubular structures were formed by anodization at various temperatures and times. The morphological and crystal structure of the anodized TiO₂ nanotubes (NTs) were characterized by scanning electron microscope (SEM) and X-ray diffraction (XRD). The photoelectrochemical (PEC) properties and incident photon-to-current conversion efficiency (IPCE) of the TiO₂ NTs were studied with different lengths and morphologies. From the detailed investigations, the optimum thickness of TiO₂ nanotubes was 3 ㎛. Moreover, we found that the optimum photocatalytic pollutant removal efficiency of TiO₂ nanotubes for photodegradation of Rhodamine B (RhB) under simulated solar light was 5.34 ㎛ of tube length.

• Corrosion Science and Technology
• /
• 제22권2호
• /
• pp.123-130
• /
• 2023

This study aimed to evaluate corrosion resistance of steel coated with GI and Zn-Al-Mg alloy using cyclic corrosion test (CCT) with electrochemical polarization and impedance measurements. Results showed that the Zn-Al-Mg alloy coated steel had a much higher corrosion rate than GI coated steel in early stages of corrosion. With prolonged immersion, however, the corrosion rate of the Zn-Al-Mg alloy coated steel greatly decreased, mainly owing to a significant decrease in the cathodic reduction reaction and an increase in polarization resistance at the surface. This was closely associated with the formation of protective corrosion products including Zn₅(OH)₈Cl₂·H₂O and Zn₆Al₂(OH)₁₆CO₃. Moreover, when the steel substrate was locally exposed due to mechanical damage, the kinetics of anodic dissolution from the coating layer and the formation of protective corrosion products on the surface of the Zn-Al-Mg alloy coated steel became much faster compared to the case of GI coated steel. This could provide a longer-lasting corrosion inhibition function for Zn-Al-Mg alloy coated steel used in plant farms.

• Composites Research
• /
• 제19권6호
• /
• pp.23-31
• /
• 2006

나노허니컴 구조물의 영률, 굽힘 탄성 계수. 공칭파괴강도를 구하였다. 양극산화 알루미늄은 잘 정렬된 나노허니컴 구조물의 일종으로서 공정이 간단하고, 높은 종횡비, 자가 정렬된 기공구조를 가지고 있고, 기공의 크기를 조절할 수 있다. 원자현미경으로 외팔보 굽힘 시험을 수행하였고 나노-UTM을 이용한 3점 굽힘 실험결과와 비교하였다. 또한 나노-UTM으로 인장시험을 수행하였다. 나노허니컴 구조물의 한쪽 면은 막혀 있어서, 일반적인 샌드위치 구조물의 면재에 비유될 수 있다. 하지만 이러한 막힌 면은 굽힘 강도 증가에 영향을 끼치지 못하고 균열선단으로 작용한다는 것을 알 수 있었다. 본 연구로 나노허니컴 구조물을 설계하는데 기초적인 물성을 제공하고자 한다.

• The Journal of Advanced Prosthodontics
• /
• 제15권3호
• /
• pp.114-125
• /
• 2023

PURPOSE. The aim of the study was to evaluate the optical properties of new generation (3Y-TZP) monolithic zirconia (MZ) with different abutment types and resin cement shades. MATERIALS AND METHODS. A1/LT MZ specimens were prepared (10 × 12 × 1 mm, N = 30) and divided into 3 groups according to cement shades as transparent (Tr), yellow (Y) and opaque (O). Abutment specimens were obtained from 4 different materials including zirconia (Group Z), hybrid (Group H), titanium (Group T) and anodized yellow titanium (Group AT). MZ and abutment specimens were then cemented. L^*, a^*, and b^* parameters were obtained from MZ, MZ + abutment, and MZ + abutment + cement. ∆E₀₀₁^* (between MZ and MZ + abutment), ∆E₀₀₂^* (between MZ and MZ + abutment + cement) and ∆E₀₀₃^* (between MZ + abutment and MZ + abutment + cement) values were calculated. Statistical analyses included 2-way ANOVA, Bonferroni, and Paired Sample t-Tests (P < .05). RESULTS. Abutment types and resin cements had significant effect on L^*, a^*, b^*, ∆E₀₀₁^*, ∆E₀₀₂^*, and ∆E₀₀₃^* values (P < .001). Without cementation, whereas zirconia abutment resulted in the least discoloration (∆E₀₀₁^* = 0.68), titanium abutment caused the most discoloration (∆E₀₀₁^* = 4.99). The least ∆E₀₀₂^* = 0.68 value was seen using zirconia abutment after cementation with yellow shaded cement. Opaque shaded cement caused the most color change (∆E₀₀₃^* = 5.24). Cement application increased the L^* values in all groups. CONCLUSION. The least color change with/without cement was observed in crown configurations created with zirconia abutments. Zirconia and hybrid abutments produced significantly lower ∆E₀₀₂^* and ∆E₀₀₃^* values in combination with yellow shaded cement. The usage of opaque shaded cement in titanium/anodized titanium groups may enable the clinically unacceptable ∆E₀₀^* value to reach the acceptable level.

• 대한융합한의학회지
• /
• 제2권1호
• /
• pp.5-12
• /
• 2021

Objectives: The purpose of this study is to fabricate an ultra-fine ginsenoside particle atomizer that can provide a new treatment method by delivering ginsenoside components that have a therapeutic effect on respiratory diseases directly to the lungs. Methods: We fabricated the AAO vibrating mesh by using the micromachining process. The starting substrate of an AAO wafer has a 350nm pore diameter with 50㎛ thickness. A photomask having several 5㎛ opening holes with a 100㎛ pitch was used to separate each nanopore nozzle. The photoresist structure was optimized to pattern the nozzle area during the lift-off process precisely. The commercial vibrating mesh was removed from OMRON's NE-U100 product, and the fabricated AAO vibrating mesh was installed. A diluted sample of 20mL with 30% red ginseng concentrate was prepared to atomize from the device. Results: As a result of liquid chromatography analysis before spraying the ginsenoside solution, ginsenoside components such as 20S-Rg3, 20R-Rg3, and Rg5 were detected. After spraying through the AAO vibrating mesh, ginsenosides of the same component could be detected. Conclusion: A nutrient solution containing ginsenosides was successfully sprayed through the AAO vibrating mesh with 350 nm selective pores. In particular, during the atomizing experiment of ginsenoside drug solution having excellent efficacy in respiratory diseases, it was confirmed that atomizing through the AAO vibrating mesh while maintaining most of the active ingredients was carried out.

• 분석과학
• /
• 제20권4호
• /
• pp.289-295
• /
• 2007

사각파형 벗김 전압 전류법과 순환 전압 전류법에서 적외선 광 다이오드의 간단한 전자 회로를 사용한 철의 정량을 연구하였다. 기존에 사용되는 작업 전극과 최적 분석 조건을 비교하였으며, 순환 전압 전류법의 결과는 보다 간단하며 정밀하였으며, 최적 조건에서 농도 범위는 0.1-0.8과 0.85-6.0 mg/L 이었다, 0.4 mg/L의 철 농도에서 15번 반복 측정한 상대 표준편차는 0.09%였으며, 최소 분석 검출 한계는 $80{\pm}0.6{\mu}g/L$ 였다, 이결과는 폐수중의 철 정량에 응용하였다.