• Journal of the Korean Society for Heat Treatment
• /
• v.29 no.4
• /
• pp.163-167
• /
• 2016

$SnO_2$ thin films were prepared by radio frequency magnetron sputtering on glass substrates and then vacuum annealed for 30 minutes at 100, 200, and $300^{\circ}C$, respectively. The thickness of films kept at 100 nm by controlling the deposition rate. While the optical transmittance and electrical resistivity of as deposited $SnO_2$ films were 82.6% in the visible wavelength region and $1.9{\times}10^{-3}{\Omega}cm$, respectively, the films annealed at $200^{\circ}C$ show the increased optical transmittance of 84.5% and the electrical resistivity also decreased as low as $8.5{\times}10^{-4}{\Omega}cm$. From the observed results, it is concluded that post-deposition vacuum annealing at $200^{\circ}C$ is an attractive condition to optimize the opto-elecrtical properties of $SnO_2$ thin films for the opto-electrical applications.

• Journal of the Korean Vacuum Society
• /
• v.11 no.1
• /
• pp.43-49
• /
• 2002

Pd/Ge/Pd/Ti/Au ohmic contact to n-type InGaAs was investigated with rapid thermal annealing conditions. Minimum specific contact resistivity of $1.1\times10^{-6}\Omega\textrm{cm}^2$ was achieved after annealing at $400^{\circ}C$/10sec, and a ohmic performance was degraded at higher annealing temperature due to the chemical reaction between the ohmic contact materials and the InGaAs substrate. However, non-spiking planar interface and relatively good ohmic contact($high-10^{-6};{\Omega}\textrm{cm}^2$) were maintained. This ohmic contact system is expected to be a promising candidate for compound semiconductor devices.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.11
• /
• pp.46-54
• /
• 1999

The output values of cellular neural networks would have errors because they can be stabilized at local minimums depending on the initial states of each cell. So, in this paper, we design the $6\times6$cellular neural networks with annealing capability which guarantees that the outputs reaches the global minimum to have correct output values independent of the initial states of each cell. This chip is designed using a $0.8\mu\textrm{m}$ CMOS technology The designed chip contains about 15,000 transistors and the chip size is about $2.89\times2.89\textrm{mm}^2$. The simulation results of edge extraction and hole filling using the designed circuit show that the outputs values would have errors in un-annealed case, but not in annealed case. In the simulation, the annealing time of $3\musec$ is employed.

• Journal of the Korean Ceramic Society
• /
• v.33 no.10
• /
• pp.1101-1108
• /
• 1996

No-doped PZT thin films have been fabricated on Pt/Ti/SiO2/Si substrate using Sol-Gel technique. A fast annealing metho (three times of intermediate and final annealing) was used for the preparation of multi-coated 1800$\AA$ thick Nb-doped PZT thin films. As Nb doping percent was increased leakage current was lowered approximately 2 order but dielectic properties were degraded due to the appearance of pyrochlore phase and domain pinning. Futhermore the increase of the final annealing temperature up to 74$0^{\circ}C$lowered the pyrochlore phase content resulting in enhancing the dielectric properties of the Nb doped films. The 3%-Nb doped PZT thin films with 5% excess Pb showed a capacitance density of 24.04 fF/${\mu}{\textrm}{m}$2 a dielectric loss of 0.13 a switchable polarization of 15.84 $\mu$C/cm2 and a coercive field of 32.7 kV/cm respectively. The leakage current density of the film was as low as 1.47$\times$10-7 A/cm2 at the applied voltage of 1.5 V.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.232-233
• /
• 2008

The 4H-SiC schottky diodes treated by the various dry etch methods were fabricated and electrically characterized. The post etch process including an Inductively Coupled Plasma(ICP) etch and a Neutron Beam Etch(NBE) was performed after a high-temperature activation annealing without graphite cap in order to eliminate the damaged surface generated during the activation annealing. The reverse leakage current of diode treated by ICP was 1/35 times lower than that of the diode without any post etch at the anode bias of -100V, while the reverse leakage current of diode treated by NBE was 1/44 times lower at the same bias.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.417-418
• /
• 2008

Transparent conductive oxide (TCO) are necessary as front electrode or anti-reflecting coating for increasing efficiency of LED and Photodiode. In this paper, aluminum-doped Zinc oxide films(AZO) were prepared by DC magnetron sputtering on glass(corning 1737) and Si substrate at temperature of $100^{\circ}C$ and then annealed at temperature of $400^{\circ}C$ for 1hr in Ar and vaccum. The AZO films were etched in diluted HCL (0.5 %) to examine the surface morphology properties. After annealing, Structural and electrical property were investigated. The c-axis orientation along (002) plane was enhanced and the electrical resistivity of the AZO film decreased from $1.1\times10^{-1}$ to $1.6\times10^{-2}{\Omega}cm$. We observed textured structure of AZO thin film etched for 2s.

• Restorative Dentistry and Endodontics
• /
• v.4 no.1
• /
• pp.7-9
• /
• 1978

Brass specimen, copper based alloy was prepared in cubic form about $1cm{\times}1cm{\times}1cm$ in volume. The specimens were mechanically compressed in one direction until the dimension distorted to 20%, 40%, 60% and 80% in length. The compressed specimens with 80% distorted in length were then heat treated in $200^{\circ}C$, $300^{\circ}C$, $400^{\circ}C$, $500^{\circ}C$ and $600^{\circ}C$ for 30 minutes. Microscopic examination was made on both compressed and heat treated specimens. The results obtained from the study were as follows: 1. Grain boundary and twin phenomenon was clearly seen in 0% and 20% compressed cases. Slip bands was appeared in 40% cases and distributed equally as well as twin. 2. The first evidence of slip bands was observed in 20% and the bands grew thicker and denser as the compression increased. 3. The density of the bands were reduced after annealing in $200^{\circ}C$ and completely disappeared at $300^{\circ}C$ cases. 4. Recrystallization was noticed unevenly in $300^{\circ}C$ cases and the evidence of twin was observed in these crystallized area. 5. In $400^{\circ}C$ cases the grain boundary was evenly found and the twin phenomenon was clearly observed. Grain boundary and twin was noticeably formed in size according to the annealing temperature increased.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.261-262
• /
• 2007

In this study we present the effect of annealing temperatures on the structural, electrical and optical characteristics of Ga-doped ZnO(GZO) films. GZO target have been deposited on corning 7059 glass substrates by DC sputtering. GZO films were annealed at temperatures of 400, 500, $600^{\circ}C$ in air ambient for 20 min. Experimental resulted in as-grown film shows the resistivity of $6{\times}10^{-1}\;{\Omega}{\cdot}cm$ and transmittance under 85%, whereas the electrical and optical properties of film annealed at $500^{\circ}C$ are enhanced up to $1.9{\times}10^{-3}\;{\Omega}{\cdot}cm$ and 90%, respectively.

• Journal of the Korean Society for Heat Treatment
• /
• v.30 no.1
• /
• pp.1-5
• /
• 2017

A 100 nm thick $SnO_2$ thin films were prepared by radio frequency magnetron sputtering on glass substrates and then annealed in nitrogen atmosphere for 30 minutes at 100, 200, and $300^{\circ}C$, respectively. While the visible light transmittance and electrical resistivity of as deposited $SnO_2$ films were 81.8% and $1.5{\times}10^{-2}{\Omega}cm$, respectively, the films annealed at $200^{\circ}C$ show the increased optical transmittance of 82.8% and the electrical resistivity also decreased as low as $4.3{\times}10^{-3}{\Omega}cm$. From the observed results, it is concluded that post-deposition annealing in nitrogen atmosphere at $200^{\circ}C$ is an attractive condition to optimize the optical and electrical properties of $SnO_2$ thin films for the various display device applications.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.261-264
• /
• 1995

The response speed enhancement in picosecond photoconductor made from RF planar magnetron sputtered hydrogenated amorphous germanium thin film is discussed. Pulsed laser annealing technique was used to fabricate the highly conductive ohmic contacts and to remove the shallow deflects in the deposited photoconductive film using the different laser powers. Measured V-I curve showed -5 times bigger conductance in photoconductive gap than the one used by the conventional vacuum annealing method using strip heater.