• 한국기계가공학회지
• /
• 제17권6호
• /
• pp.53-60
• /
• 2018

In this paper, the effect of different 3D printing parameters including laminated angle and annealing temperature is observed their effect on FDM conductive 3D printing. In FDM 3D printing, a conductive filament is heated quickly, extruded, and then cooled rapidly. FDM 3D Print conductive filament is a poor heat conductor, it heats and cools unevenly causing the rapid heating and cooling to create internal stress. when the printed conductive specimens this internal stress can be increase electrical resistance and decrease electrical conductivity. Therefore, This experiment would like to use annealing to remove internal stress and increase electrical conductivity. The result of experiment when 3D printing conductive specimen be oven cooling of annealing temperature $120^{\circ}C$ electrical resistance appeared decrease than before annealing. So We have found that 3D printing annealing removes internal stresses and increases the electrical conductivity of printed specimens. These results are very useful for making conductive 3D printing electronic circuit, sensor ect...with electrical conductance suitable for the application.

• 한국기계가공학회지
• /
• 제18권2호
• /
• pp.82-90
• /
• 2019

In this paper, the effects of different 3D printing conditions including oil lubrication and annealing are observed for their effects on tensile testing. In 3D printing, a press-out extrude filament is rapidly heated and cooled to create internal stress in the printed part. The 3D printing internal stress can be removed using oil-coated filament and annealing. During the oven cooling at an annealing temperature of $106^{\circ}C$, the stress of the specimens with laminated angle $0^{\circ}$ tends to increase by 12.6%, and that of the oil-coated filament printing specimens is increased by 17%. At the annealing temperature of $106^{\circ}C$, the stress of the oil-coated filament printing specimens tends to increase by 35%. In this study, we have found that the oil lubrication and annealing remove the internal stresses and increase the strength of the printed specimens. The oil lubrication and annealing reform the crystalline structures to even out the areas of high and low stress, which creates fewer fragile areas. These results are very useful for the manufacture of 3D printing products with a suitable mechanical strength for applications.

• 한국재료학회지
• /
• 제24권9호
• /
• pp.443-450
• /
• 2014

Amorphous (a-Si) films were epitaxially crystallized on a very thin large-grained poly-Si seed layer by a silicide-enhanced rapid thermal annealing (SERTA) process. The poly-Si seed layer contained a small amount of nickel silicide which can enhance crystallization of the upper layer of the a-Si film at lower temperature. A 5-nm thick poly-Si seed layer was then prepared by the crystallization of an a-Si film using the vapor-induced crystallization process in a $NiCl_2$ environment. After removing surface oxide on the seed layer, a 45-nm thick a-Si film was deposited on the poly-Si seed layer by hot-wire chemical vapor deposition at $200^{\circ}C$. The epitaxial crystallization of the top a-Si layer was performed by the rapid thermal annealing (RTA) process at $730^{\circ}C$ for 5 min in Ar as an ambient atmosphere. Considering the needle-like grains as well as the crystallization temperature of the top layer as produced by the SERTA process, it was thought that the top a-Si layer was epitaxially crystallized with the help of $NiSi_2$ precipitates that originated from the poly-Si seed layer. The crystallinity of the SERTA processed poly-Si thin films was better than the other crystallization process, due to the high-temperature RTA process. The Ni concentration in the poly-Si film fabricated by the SERTA process was reduced to $1{\times}10^{18}cm^{-3}$. The maximum field-effect mobility and substrate swing of the p-channel poly-Si thin-film transistors (TFTs) using the poly-Si film prepared by the SERTA process were $85cm^2/V{\cdot}s$ and 1.23 V/decade at $V_{ds}=-3V$, respectively. The off current was little increased under reverse bias from $1.0{\times}10^{-11}$ A. Our results showed that the SERTA process is a promising technology for high quality poly-Si film, which enables the fabrication of high mobility TFTs. In addition, it is expected that poly-Si TFTs with low leakage current can be fabricated with more precise experiments.

• 한국세라믹학회지
• /
• 제43권2호
• /
• pp.106-113
• /
• 2006

PMN-PZT films with thickness of $5\;{\mu}m$ were deposited on $Pt/Ti/SiO_2/Si$ substrate at room temperature using aerosol deposition process. The films showed fairly dense microstructure without any crack. XRD and TEM analysis revealed that the films consisted of randomly oriented nanocrystalline and amorphous phases. Post-annealing process was employed to induce crystallization and grain growth of the as-deposited films and to improve the electrical properties. The annealed film showed markedly improved electrical properties in comparison with as-deposited film. The film after annealing at $700^{\circ}C$ for 1h exhibited the best electrical properties. Dielectric constant $(\varepsilon_r)$, remanent polarization $(P_r)$ and piezoelectric constant $(d_{33})$ were 1050, $13\;{\mu}C/cm^2$ and 120 pC/N, respectively.

• 한국진공학회지
• /
• 제22권1호
• /
• pp.31-36
• /
• 2013

마이크로플라즈마 화학기상증착법(microwave plasma enhanced chemical vapor deposition, MPCVD)에 의하여 형성된 비정질 탄소 박막의 효율적인 도핑 공정을 위하여, 비정질 탄소 박막의 성장 직전 nucleated seed 상태의 기판 혹은 일부 성장된 박막 위에 비소(As) 이온을 이온 주입하였고 그 직후 다시 MPCVD에 의하여 박막을 성장시켰다. MPCVD에 의한 성장 자체가 약 $500{\sim}600^{\circ}C$ 온도에서의 어닐링 공정을 대체할 수 있으므로, 기존의 이온 주입 후 별도의 어닐링 공정과 비교 시 간략화된 공정으로도 어닐링 효과가 있다고 할 수 있다. 이온 주입 후 박막 성장으로 어닐링 효과를 얻은 비정질 탄소 박막의 경우, $2.5V/{\mu}m$의 전계에서 약 $0.1mA/cm^2$의 전계 방출 특성을 관찰할 수 있었고 또한 라만 스펙트럼 특성에서도 다이아몬드 특성 및 그래파이트 특성 모두 뚜렷이 관찰되었다. 전기적, 구조적 특성 관찰로부터 이온 주입된 As 이온이 자동 어닐링 효과에 의해 충분히 비정질 탄소 박막에 도핑되었다고 할 수 있다.

• 융합신호처리학회논문지
• /
• 제3권4호
• /
• pp.35-41
• /
• 2002

복잡한 문제들의 근사해를 구하기 위하여 최근 다양한 방법들이 소개되고 있다. 이러한 방법들은 주로 금속의 서랭(Annealing)에 의해 금속분자의 에너지가 최저점에 도달하는 과정을 모의실험한 최적화 기법(Simulated Annealing), 생물의 적자생존(Survival of Fittest)과정을 이용한 최적화 기법인 유전적 알고리즘(Genetic Algorithm)등 물리적 현상이나 생물 ?생명에 관련된 모의를 최적화 문제에 응용한 방법들이다. 최근에 소개된 Particle Swarm Optimization(PSO)는 주로 조류나 어류등의 생물의 무리가 각각의 개체가 가지고 있는 정보를 공유해가며 먹이를 찾아가는 과정을 모의한 기법이다. 하지만, 이 기법의 탐색과정이 명확하게 밝혀져 있지 않다. 본 논문에서는 PSO의 탐색과정을 가시화 하는 것을 목적으로 한다. 탐색과정을 가시화 하는 작업을 통해 그 탐색 능력을 시각적으로 파악하는 것이 가능하며 기법에 관한 이해를 돕고 교육적 효과도 기대 가능하다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2008년도 하계종합학술대회
• /
• pp.651-652
• /
• 2008

In this paper, we suggest a new multiobjective optimization algorithm which is based on the simulated annealing(SA) method. The proposed algorithm uses population-based simulated annealing and adapts elitism in the process of selection.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
• /
• pp.254-257
• /
• 2009

The crystallization and activated annealing effect of Si films using an excimer laser and a new CW blue laser are described comparing with furnace annealing (SPC) for the application of advanced TFTs and future applications. Currently, pulsed ELA is used extensively as a LTPS process on glass substrates as the efficiency is high in UV region for thin Si film of 40- 60 nm thickness. ELA enables extremely low resistivity for both n- and p-typed Si films. On the other hand, CW BLDA enables the smooth Si surface having arbitral grains from micro-grains to anisotropic huge grain structure only controlling its power density.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 A
• /
• pp.193-195
• /
• 1996

In amorphous transformer core, magnetic field annealing is required for inducing uniaxial magnetic anisotropy to circular direction of the core. Generally annealing temperature is about foot, so insulator using in solenoid bed must have a high temperature stability, mechanical strength and good machinability. In this study, we made the magnetic field annealing apparatus using insulators, conductors, connectors and power supply. And then tested the apparatus in annealing process of 50 kVA amorphous transformers.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1997년도 추계학술대회 논문집
• /
• pp.101-107
• /
• 1997

Development on the mechanical properties of steel sheet for the automobile body panel is very important in the BAF(Batch annealing furnace) annealing process. Because of the heat treatment method in the BAF, mechanical properties was decided on the heat treatment method of the coil. So, we tested on the development of mechanical properties according to heat treatment method at the annealing furnace using the Ax atmospheric gas and the HNx atmospheric gas. As a result of several investigations. We confirmed the following characteristics ; mechanical properties was changed under the influence of the annealing cycle, the heat treatment method and the atmospheric gas. And, elongation in the HNx BAF was better than the Ax BAF. Finally, most important thing in the BAF is using proper annealing cycle in order to get a good quality.