• Journal of the Korean Magnetics Society
• /
• v.27 no.1
• /
• pp.30-34
• /
• 2017

In this report, we calculated the angular dependence of exchange bias ($H_{ex}$) by using single domain model in exchange coupled ferromagnetic (F)/antiferromagnetic (AF) bilayers, which results with AF thickness ($t_{AF}$) were used for the analysis of measured ones in NiFe/MnIr bilayers. Angular dependence of $H_{ex}$ calculated at $t_{AF}$ > $t_c$ showed typical unidirectional behaviors, however, calculated one at $0.5t_c$ < $t_{AF}$ < $t_c$ showed peculiar angular behaviors by fixed AF spins at specified angle near ${\theta}_H=90^{\circ}$. Angular dependence of $H_{ex}$ measured in NiFe/MnIr (20 nm) bilayers showed typical unidirectional behaviors. However, measured one in NiFe/MnIr (4 nm) bilayers showed mixed behaviors including both of unidirectional and peculiar angular behaviors, which was explained by the grain size distribution of polycrystalline MnIr.

• Journal of the Korean Ceramic Society
• /
• v.23 no.5
• /
• pp.47-54
• /
• 1986

The structures of crystalline vitreous and liquid $SiO_2$ were Monte carlo simulated employing the potential energy function comprising Lennard-Jones 2-body and Axilrod-Teller 3-body potentials. Although the Si-O-Si angular distribution functions obtained in the simulation appear to be higher than the experimental results the other simulation results including SiO, O-O and Si-Si radial distribution functions and O-Si-O anglular distribution functions agree well with experimental data within acceptable limits. Themost important outcome in this study is that various $SiO_2$forms were successfully reproduced with the same potential energy function.

• Tribology and Lubricants
• /
• v.5 no.2
• /
• pp.48-54
• /
• 1989

The effects of angular misalignment, coning and the temperature difference between the primary seal ring and the seal seat on the pressure distribution in mechanical face seals are analyzed. The modified Reynolds equation for the temperature dependent viscosity was solved by a finite difference approximation and Gauss-Seidel method. It is shown that the amplitude of pressure is significantly affected by the misalignment of the seals and a large temperature difference between the rotor and the stator.

• Radiation Oncology Journal
• /
• v.7 no.2
• /
• pp.313-320
• /
• 1989

In capacitive heating device, which considered efficient for deep heating, parallel arrangement of the electrodes is a serious limiting factor in heating for eccentrically located lesions because it causes overheating of the exposed ipsilateral skin surface, the heating pattern is also frequently inappropriate, and the arrangement tends to be unstable due to the patient's gravity. Therefore we attempted an angular arrangement of the electordes to achieve more homogenous and efficient heating for such lesions. In phantom study, both the thermal profile and thermogram established the heating pattern in this unusual angular arrangement of the electrodes at $60^{\circ},\;90^{\circ}\; and\;120^{\circ}$ angles, respectively. An angular arrangement was also clinically applied to 3 patients. The patients' tolerance was good without significant complication and the thermal distribution was satisfactory. In conclusion, this unusual arrangement of electrodes appears to be promising in the clinical application to the eccentrically located lesions.

• The Korean Journal of Applied Statistics
• /
• v.22 no.1
• /
• pp.205-220
• /
• 2009

For modeling skewed semicircular data, we derive new family of the exponential distributions. We extend it to the l-axial exponential distribution by a transformation for modeling any arc of arbitrary length. It is straightforward to generate samples from the f-axial exponential distribution. Asymptotic result reveals two things. The first is that linear exponential distribution can be used to approximate the l-axial exponential distribution. The second is that the l-axial exponential distribution has the asymptotic memoryless property though it doesn't have strict memoryless property. Some trigonometric moments are also derived in closed forms. Maximum likelihood estimation is adopted to estimate model parameters. Some hypotheses tests and confidence intervals are also developed. The Kolmogorov-Smirnov test is adopted for goodness of fit test of the l-axial exponential distribution. We finally obtain a bivariate version of two kinds of the l-axial exponential distributions.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.6
• /
• pp.913-922
• /
• 1987

In this paper the solidification phenomena at the molten pool has been modeled and simulated in terms with the one dimensional unsteady-state heat transfer of the solid and molten phase and the pressure distribution in the solid phase for the twin-roller continuous casting of Sn-15% Pb. The further purpose of this study was to effectively analyze the thermal and mechanical deformation of roll applying the results of the heat transfer and the pressure distribution to the boundary conditions. The strip thickness of rapidly solidified metallic strip decreases with increasing angular velocity of the roller and with increasing initial roll gap. For this reason the roll spacing and angular velocity of the rolls are considered to be main variables. The recommended optimal casting regimes for continuous strip dimensions is near 0.8mm-1.0mm in thickness at the given angular velocity .omega.=2.0 rad/sec. Results of the experiment using Sn-15% Pb are compared with model predictions. The calculated roll deformation has been in good agreement with the observed value of roll deformatiion. All the deformation. All the deformation of the roller is within the elastic range, the plastic yielding are not occured. However, these elastic stresses are sufficient to take place of the shortened roller life by the thermal fatigue and a notch fatigue. The higher cooling rates were obtained by a twin-roller quenching technique. Also the quenched microstructure of the rapidly solidified shell was verified.

• Korean Journal of Remote Sensing
• /
• v.26 no.6
• /
• pp.653-664
• /
• 2010

The land surface reflectance is a key parameter influencing the climate near the surface. Therefore, it must be determined with sufficient accuracy for climate change research. In particular, the characteristics of the bidirectional reflectance distribution function (BRDF) when using earth observation system (EOS) are important for normalizing the reflected solar radiation from the earth's surface. Also, wide swath satellites like SPOT/VGT (VEGETATION) permit sufficient angular sampling, but high resolution satellites are impossible to obtain sufficient angular sampling over a pixel during short period because of their narrow swath scanning. This gives a difficulty to BRDF model based reflectance normalization of high resolution satellites. The principal objective of the study is to add BRDF modeling of high resolution satellites and to supply insufficient angular sampling through identifying BRDF components from SPOT/VGT. This study is performed as the preliminary data for apply to high-resolution satellite. The study provides surface parameters by eliminating BRD effect when calculated biophysical index of plant by BRDF model. We use semi-empirical BRDF model to identify the BRD components. This study uses SPOT/VGT satellite data acquired in the S1 (daily) data. Modeled reflectance values show a good agreement with measured reflectance values from SPOT satellite. This study analyzes BRD effect components by using the NDVI(Normalized Difference Vegetation Index) and the angle components such as solar zenith angle, satellite zenith angle and relative azimuth angle. Geometric scattering kernel mainly depends on the azimuth angle variation and volumetric scattering kernel is less dependent on the azimuth angle variation. Also, forest from land cover shows the wider distribution of value than cropland, overall tendency is similar. Forest shows relatively larger value of geometric term ($K_1{\cdot}f_1$) than cropland, When performed comparison between cropland and forest. Angle and NDVI value are closely related.

• Journal of the Korean Magnetics Society
• /
• v.26 no.2
• /
• pp.50-54
• /
• 2016

We analyzed the angular dependence of ferromagnetic resonance linewidth in exchange coupled CoFe/MnIr bilayers. The maximum and minimum linewidth was observed in the easy and hard direction of unidirectional anisotropy by exchange coupling, respectively, and it was well agreed with the angular dependence of exchange bias field. The maximum linewidth was due to the twist of CoFe magnetization near CoFe/MnIr interface from direction of pinned MnIr spin to direction of applied magnetic field. While, minimum linewidth more higher than that of CoFe was related to rotatable anisotropy field, and explained by easy axis distribution of MnIr grains.

• Bulletin of the Korean Chemical Society
• /
• v.23 no.2
• /
• pp.189-194
• /
• 2002

Two-photon resonant third photon ionization of atomic bromine $(4p^5\;^2P_{3/2}\;and\;^2P_{1/2})$ has been studied using a photoelectron imaging spectroscopy in the wavelength region 250 - 278 nm. The technique has yielded simultaneously both relative branching ratios to the three levels of $Br^+(^3P_2,\;^3P_{0.1}\;and^1D_2)$ with $4p^4$ configuration and the angular distributions of outgoing photoelectrons. The product branching ratios reveal a strong propensity to populate particular levels in many cases. Several pathways have been documented for selective formation of $Br^+(^3P_2)$ and $Br^+(^3P_{0.1})$ ions. In general, the final ion level distributions are dominated by the preservation of the ion core configuration of a resonant excited state. Some deviations from this simple picture are discussed in terms of the configuration interaction of resonant states and the autoionization in the continuum. The photoelectron angular distributions are qualitatively similar for all transitions, with a positive $A_2$ anisotropy coefficient of 1.0-2.0 and negligible $A_4$ in most cases, which suggests that the angular distribution is mainly determined by the single-photon ionization process of a resonant excited state induced from the third photon absorption.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.6
• /
• pp.182-187
• /
• 2001

Much research efforts have been made on the equal-channel angular pressing(ECAP)that produces ultra-fine grain size materials. Recently many materials have been tested for ECAP process, and in this paper pure-Zirconium is considered due to its applicability to nuclear reactors. Among many process parameters of ECAP, frictional effects on the deformation behavior of materials and on the stress distribution of die have been investigated. The finite element method has been employed in order to investigate this issue, and experiments have also been made to verify the numerical results.