• Journal of Biosystems Engineering
• /
• 제25권3호
• /
• pp.233-240
• /
• 2000

A commercially available Doppler radar was modified and evaluated for on-board monitoring of ground speed. The radar output was corrected for pitch angle of aircraft based on the output of an electrolytic tilt sensor. The effects of aircraft speed, height and mounting angle on error in the ground speed were evaluated. The speed error decreased with an increase of the mounting angle since the radar contact angle with respect to the ground approached to the mounting angle. The error increased with an increase of the nominal aircraft speed. The altitude insignificantly affected the speed error. The Doppler radar provided acceptable percent errors within 5% in most measurements. The error can be reduced within ${\pm}$1.5% by increasing the mounting angle ($43^{\circ}$). The error of -3.8% at the mounting angle of $29^{\circ}$could be reduced by adjusting the mounting angle with respect to the radar contact angle.

• 대한치과교정학회지
• /
• 제45권6호
• /
• pp.282-288
• /
• 2015

Objective: This study investigated whether it is possible to use a two-dimensional (2D) standard in three-dimensional (3D) analysis, by comparing the angles and lengths measured from a midsagittal projection in 3D cone-beam computed tomography (CBCT) with those measured by 2D lateral cephalometric radiography (LCR). Methods: Fifty patients who underwent both LCR and CBCT were selected as subjects. CBCT was reoriented in 3 different methods and the measuring-points were projected onto the midsagittal plane. Twelve angle values and 8 length values were measured on both LCR and CBCT and compared. Results: Repeated measures analysis of the variance revealed statistically significant differences in 7 angular and 5 linear measurements among LCR and 3 types of CBCT (p < 0.05). Of these 12 measurements, multiple comparisons showed that 6 measurements (ANB, AB to FH, IMPA, FMA, Co-Gn, Go-Me) were not significantly different in pairwise comparisons. LCR was significantly different from 3 types of CBCT in 3 angular (SN to FH, interincisal angle, FMIA) and 2 linear (S-Go, Co-ANS) measurements. The CBCT method was similar for all measurements, except for 1 linear measurement, i.e., S-N. However, the disparity between the mean values for all parameters was within the range of clinical measurement error. Conclusions: 3D-CBCT analysis, using midsagittal projection, is a useful method in which the 2D-LCR normative values can be used. Although the measurements changed with reorientation, these changes were not clinically significant.

• 한국전기전자재료학회논문지
• /
• 제33권3호
• /
• pp.245-248
• /
• 2020

The wettability of silicon carbide (SiC) crystal, which has 6H-SiC and 4H-SiC regions prepared using the physical vapor transport (PVT) method, is quantitatively analyzed using dispensed deionized (DI) water droplets. Regardless of the polytypes in SiC, the average of five contact angle measurements showed a difference of about 6° between the Si-face and C-face. The contact angle on the Si-face (C-face) is measured after the removal of the native oxide using BOE (6:1), and revealed a significant decrease of the contact angle from 74.9° (68.4°) to 47.7° (49.3°) and from 75.8° (70.2°) to 51.6° (49.5°) for the 4H-SiC and 6H-SiC regions, respectively. The contact angle of the Si-face recovered over time during room temperature oxidation in air; in contrast, that of the C-face did not recover to the initial value. This study shows that the contact angle is very sensitive to SiC surface polarity, specific surface conditions, and process time. Contact angle measurements are expected to be a rapid way of determining the surface polarity and wettability of SiC crystals.

• 한국전문물리치료학회지
• /
• 제12권4호
• /
• pp.41-47
• /
• 2005

The purpose of this study was to determine the intra-rater and inter-rater reliability of various forward head posture measurements. Ten healthy adults (age, $20.4{\pm}2.2$ yrs; height, $164.0{\pm}5.5$ cm; weight, $58.7{\pm}7.3$ kg) participated in the study. They were free of injury and neurologic deficits in the upper extremities and neck at the time of testing. The subjects were asked to perform head forward posture by under the guidance of physical therapists. Markers were placed on the C7 spinous process, mastoid process, tragus of the ear, outer canthus, and forehead. Measurement 1 for forward head posture assessment was measured as the angle between the horizontal line through C7 and the line connecting the C7 spinous process with the tragus of the ear. Measurement 2 was measured as the angle between the C7 spinous process, the mastoid process and the outer canthus. Measurement 3 was measured as two kinds of angles the HT (head tilt) angle is between the line from the midpoint of forehead to the tragus line and Y-axis at the tragus point. The NF (neck flexion) angle is between the line from the tragus to the C7 line and the Y-axis at the C7. Intra-rater, inter-rater reliability and coefficient of variation was assessed by comparing the measured values from three kinds of measurements of forward head posture. The intra-rater reliability was indicated by intraclass correlation coefficients [ICC(1,1)] and inter-rater reliability was shown by intraclass correlation coefficients [ICC(3,k)]. The results of study were as follows: ICC(1,1) values for intra-rater reliability of three measurements were in the 'excellent' category. ICC(3,k) values for inter-rater reliability of three measurements were also in the 'excellent' category. The coefficient of variation of method 2 had a lower value than method 1 and method 3. This data means that the measured value of method 2 was less scattered. Further research is needed to determine whether the validity of all measurements is revealed in the 'excellent' category.

• 대한치과교정학회지
• /
• 제18권2호
• /
• pp.459-474
• /
• 1988

두부(頭部)X선규격사진법(線規格寫眞法)이, 치과교정학(齒科矯正學)에 도입(導入)된 이래(以來), 악안면두개(顎顔面頭蓋)의 형태학적연구(形態學的硏究)에 획기적(劃期的) 수단(手段)으로서 응용(應用)되여, 치과교정학(齒科矯正學)에 관(關)한 증례분석(症例分析) 및 치료평가(治療評價)에 중요(重要)한 방법(方法)으로서 채용(採用)되고 있다. 저자(著者)는 정상교합(正常咬合)의 한국인성인남녀(韓國人成人男女)의 두부(頭部)X선규격사진(線規格寫眞)을 이용(利用)하여, 표준치(標準値)의 산정(算定) 및 일본인(日本人), 백인(白人)과의 비교검사(比較檢詐)를 행(行)하였다. 자료(資料)로서는 성년남자(成年男子) 50명(名) 여자(女子) 계(計) 100명(名)을 촬영(撮影)하여 자료(資料)로 하였다. 연구방법(硏究方法)으로서는 6종(種)의 분석법(分析法)을 이용(利用)하여 계측(計測)하였으며, 저자(著者)가 설정(設定)한 U-1 lluxley line angle을 가(加)한 58종(種)의 계측항목(計測項目)에 대(對)하여 계측(計測)검토(檢討)하였으며, 다음과 같은 결과(結果)를 얻었다. 1. 각분석법(各分析法)에 의한 한국인성인(韓國人成人)의 표준치(標準値)를 남녀별(男女別)로 산출(算出)하였으며, 치과교정(齒科矯正) 진단(診斷)에 응용(應用)하기위하여 합리적(合理的)이라고 생각되는 14계측항목(計測項目)을 선정(選定)하여 표준편차도표(標準偏差圖表)와 cephalometric profilogram을 작성(作成)하였다. 2. 본자료(本資料)에서의 남녀간(男女間)의 성차(性差)의 유의성(有意性)은 각도적계측항목(角度的計測項目)에서는 없었으며, 거리적계측(距離的計測)에 있어서는 유의차(有意差)가 나타났다. 3. 일본인(日本人)과의 비교(比較)에 있어서는 남녀(男女)의 gonial angle, 남성간(男性間)의 interincisal angle에서 유의차(有意差)가 나타났으나, 평균치차(平均値差)가 많지않았으며, 한국인(韓國人)과의 유이성(類以性)이 강(强)하게 나타났으며, 여성(女性)에 있어서는 남성(男性)보다 더욱 강(强)한 유이성(類以性)이 나타났다. 4. 백인(白人)과의 비교(比較)에 있어서는 angle of convexity, mandibular plane angle, Y-axis angle, interincisal angle, L-I to mandibular plane angle에서 유의차(有意差)가 나타났으며, 한국인(韓國人)은 백인(白人)보다 convex type의 안예(顔猊)였다. 5. 신설계측항목(新設計測項目)으로서 upper incisal to Huxley line angle을 설정(設定)하였으며, upper incisal axis와 X-Y axis가 거의 평행상태(平行狀態)인것이 발견(發見)되었다.

• 한국의상디자인학회지
• /
• 제10권2호
• /
• pp.105-115
• /
• 2008

Men's outer wear, such as jackets and coats appeared since the 16th century. They have been changed from doublets, coats, justaucorps, tail-coats, frock coats and morning coats to contemporary men's suits. Since the early 17th century, sleeve patterns of men's outer jackets had been mostly two-pieces close fitted patterns. The purpose of this article is to compare sleeve patterns of various jackets, which appear in various historic costume books. Armhole measurements, sleeve head measurements, amounts of ease, armhole depths, armhole widths, crown heights, sleeve width and sleeve angle had been compared to find out the differences among patterns of different times and styles. Coming to the present, the difference between top sleeve and under sleeve became more obvious, and the sleeve angle became less curvy. Another interesting point is that there had been considerable amounts of ease, which is the difference between sleeve head measurements and corresponding armhole measurements. It is because the sleeve has been attached to the armhole not by seam but by string. It is believed that the present sleeves have more natural curve and shape compared to the past.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1703-1708
• /
• 2003

The present study investigates the effect of injection angle of water mist on fire suppression characteristics by numerical simulation. In order to validate the temperature field by numerical simulation, the predicted results are compared with experimental data. It shows that the temperature difference between measurements and predictions are within $10^{\circ}C$ Numerical simulations of fire suppression are performed for 4 different injection angle($60^{\circ}$, $90^{\circ}$, $120^{\circ}$, and $180^{\circ}$). The grobal mean temperature over the fire compartment decrease with increasing of spray angle. The result shows that the heat transfer between droplets and gas phase are enhaced with the increasing of spray angle. Near the fire source, temperature field by the wide spray angle is slightly higher than that of narrow injection angle because of direct cooling of fire source.

• 한국안전학회지
• /
• 제18권2호
• /
• pp.28-33
• /
• 2003

The present study investigates the effect of injection angle of water mist on fire suppression characteristics by numerical simulation. In order to validate the temperature field by numerical simulation, the predicted results are compared with experimental data. It shows that the temperature difference between measurements and predictions are within $10^{\circ}C$. Numerical simulations of fire suppression are performed for 4 different injection angle($60^{\circ}$, $90^{\circ}$, $^120{\circ}$, and $180^{\circ}$). The global mean temperature over the fire compartment decrease with increasing of spray angle. The result shows that the heat transfer between droplets and gas phase are enhanced with the increasing of spray angle. Near the fire source, temperature field by the wide spray angle is slightly higher than that of narrow injection angle because of direct cooling of fire source.

• PNF and Movement
• /
• 제8권3호
• /
• pp.39-47
• /
• 2010

Purpose : The purpose of this study was to investigate the correlations between clinical balance scales and Balance Performance Monitor parameters in patient with adolescent idiopathic scoliosis (AIS). Methods : Twenty AIS subjects (age, $14.26{\pm}1.93yrs$; height, $160.56{\pm}7.98cm$; weight, $47.54{\pm}6.94kg$)were participated in this study. Postural sway(mean balance, sway angle, sway area, sway path, maximal sway velocity) were were evaluated by balance performance monitor. Measurements for clinical balance scales were Functional reach test (both side), the Lateral reach test (both side) and One leg standing test (both legs). Results : The results were as follows. There were positive strong correlation between major curve direction and left-right sway angle, sway path, maximal sway velocity. There were negative strong correlation between the functional reach and left-right sway angle, sway area, sway path, maximal sway velocity. And the lateral reach were also showed negative strong correlation parameters of balance performance monitor. One leg standing were negatively correlated with left-right sway angle, sway path, maximal sway velocity. Conclusion : The clinical balance scales will be useful tools for balance measurements, and basic tools for clinical setting for patient with AIS.

• Journal of Oral Medicine and Pain
• /
• 제41권2호
• /
• pp.41-47
• /
• 2016

Purpose: The purpose of this study was to analyze the size and morphology of mandibular condyle and mandibular fossa between temporomandibular joint (TMJ) disc displacement (DD) patients and healthy subjects using cone-beam computed tomography (CBCT). Methods: Twenty healthy subjects and twenty TMJ DD patients participated in this study respectively. We made five measurements in mandibular condyle (medio-lateral dimension, antero-posterior dimension, condyle height, intercondylar distance and intercondylar angle) and two measurements in mandibular fossa (mandibular fossa depth and articular eminence angle) using CBCT image. Results: There was no difference between two groups in medio-lateral dimension. In case of antero-posterior dimension, average of healthy controls was larger than that of TMJ DD patients, but that was not significant statistically. There were no significant differences between two groups in condyle height. Comparing intercondylar distance and intercondylar angle between two groups, there was no significant difference between two groups. In comparison of mandibular fossa depth and articular eminence angle, there was no significant difference between two groups. Conclusions: We couldn't find any definite relationship between TMJ morphology and TMJ DD.