• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.545-552
• /
• 2003

For temporary excavation support in a congested urban area, the strand of ground anchor should be removed to get permission of the private land to install anchors. But the strand doesn't need to be removed in the outside city area after use. So the anchor body, tension anchor, is fabricated in-situ. The unbonded length of This anchor has several strands, which wrap only one sheath. When the anchor body is carried into job-site or installed in the bore hole, the sheath is torn easily because it is a very week material. So the grout permeate into the torn sheath. Because of that, the load doesn't transfer to the bond length of ground anchors. It may indicate that load is being transferred along the unbonded length and thus within the potential slip surface assumed for overall stability of the anchored system. The load tests were performed on seven low-pressure grouted anchors installed in weathered soil to verify its problems. Four anchors(Type A) have the unbonded length, which consist of five strands and a week sheath and three anchors(Type B) have strands, which is covered by plastic sheath filled with grease, in the unbonded length. Both anchors are compared with load tests results.

• 기술발표회
• /
• s.2006
• /
• pp.342-355
• /
• 2006

The Tunnel portal is designed on temporary support system which is composed by 28m height H-Pile method and Ground Anchor method. The tunnel has excavated about 30m from the portal, but some deformation is found on the surface ground just above the tunnel face. It was investigated very carefully to find out the causes of deformation. By the observation and study, two main causes of deformation are found out. The one is earth pressure increase compared with classical earth pressure theory. That was due to the direction of ground rock mass's discontinuities. It causes the increase of earth pressure that are activated by the direction of discontinuity. The other one is that present design method neglect the transferred force by removal of temporary support members and ground anchor within the tunnel contour line as the tunnel excavation proceeds As the result of removals of the member and anchor, some force transferred from removed systems to remaining supporting systems. In designing the portal support systems, lt must be considered the discontiunity of ground mass and the transfered force due to excation.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.7
• /
• pp.7-17
• /
• 1998

Stereolithography is a process used to rapidly produce stereolithographic parts directly from three dimensional CAD models. However design methodologies to create components to be built by stereolithography are different from those required by conventional machining processes. As a typical case in point, the support structures are required to support a component at build stage, but are later removed once building and curing are complete. These structures are used to anchor the component to the platform and to prevent sagging or distortion. This paper deals with the Support Map data structure prepared to find the appropriate regions of supports. Interferences between supports and parts, and support structure themselves as well, are checked and thus the system are searching the statically stable regions to remove the surplus support structures. Cross shaped tooth profiles are designed for easy eliminating the support structures.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.1
• /
• pp.201-210
• /
• 2012

Now, there are many mobile nodes are efficient and stable when they move to operate with variety techniques have emerged.Recently, there is a growing interest about PMIPv6(Proxy Mobile IPv6) and, in this proposal of essay is the based on the way to mobility support system will stand on the basis from PMIPv6 network to NEMO(Network Mobility). PMIPv6 is mobility support system from single domain, it actual network is composed with nested in a multiple domain structural system. The proposed technique in the domain of two or more, the LMA(Local Mobility Anchor) communication between LMA(Local Mobility Anchor) and MAG(Mobile Access Gateway) of movable domain can increase performance by handover delay and signaling.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.6 no.2 s.21
• /
• pp.17-24
• /
• 2006

A ground anchor system is used as a load carrying element for soil structure stability The conventional systems with ground anchors bring about the anchorage loss of wedges when anchors are installed for the support of soil structures. Hence we developed the new type of anchor system using both the spacing apparatus and spring (length 60mm, diameter 6mm). In this system, we can directly check the condition of wedges and PS strands and modify the problems with the slip and anchorage of wedges under construction. For demonstrating the superiority of this system, we carried out a series of both laboratory and field test. Consequently, we can obtain satisfactory result (18.99% reduction to the loss of conventional systems). Moreover, the replacement of wedges is easy and simple when retensioning of strands.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.1351-1358
• /
• 2008

This paper presents how the load transfer mechanism of the ground anchor affects on the stability analysis of anchored slope. The finite element analysis and the conventional limit equilibrium analysis on the anchored slope were performed and compared. The limit equilibrium analysis of the anchored slope is quite open used in design practice due to the easiness of the analysis. However, the load transfer mechanism is not considered properly for the analysis. When the failure surface passes through the bonded length of an anchor, the anchor load is disregarded and the factor of safety for the anchored slope is smaller than it should be. In this study, the load transfer distribution was incorporated into the limit equilibrium stability analysis of the anchored slope and the results were compared with the results of finite element analysis.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.3
• /
• pp.41-70
• /
• 1999

The benefits of utilizing internal reinforced members, such as soil nails and ground anchors, in maintaining stable excavations and slopes have been known among geotechnical engineers to be very effective. Occasionally, however, both soil nails and ground anchors are simultaneously used in one excavation site. In the present study, a method of limit equilibrium stability analysis of the excavation zone reinforced with the vertically or horizontally mixed nail-anchor system is proposed to evaluate the global safety factor with respect to a sliding failure. The postulated failure wedges are determined based on the results of the $FLAC^{2D}\; 및\; FLAC^{3D}$ program analyses. This study also deals with a determination of the required thickness of the shotcrete facing. An excessive facing thickness may be required due to both the stress concentration and the relative displacement at the interface zone between the soil nailing system and the ground anchor system. A simple finite element method of analysis is presented to estimate the corresponding relative displacement at the interface zone between two different support systems. As an efficient resolution to reduce the facing thickness, the modified bearing plate system is also proposed. Finally with various analysis related to the effects of design parameters, the predicted displacements are compared with the results of the $FLAC^{2D}$ program analyses.

• Geomechanics and Engineering
• /
• v.11 no.2
• /
• pp.177-195
• /
• 2016

To secure the stability of geotechnical infrastructures and minimize failures during the construction process, a number of support systems have been introduced in the last several decades. In particular, stabilization methods using steel bars have been widely used in the field of geotechnical engineering. Rock bolt system is representative support system using steel bars. Pre-stressing has been applied to enhance reinforcement performance but can be released because of the failure of head or anchor sections. To overcome this deficiency, this paper proposes an innovative support system that can actively reinforce the weak ground along the whole structural element by introducing an active tension bolt containing a spring unit to the middle of the steel bar to increase its reinforcement capacity. In addition, the paper presents the support mechanism of the active tension bolt based on a theoretical study and employs an experimental study to validate the performance of the proposed active tension bolt based on a down-scaled model. To examine the feasibility of the active tension unit in a pillar, the paper considers a pullout test and a small-scale experimental model. The experimental results suggest the active tension bolt to be an effective support system for pillar reinforcement.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.587-591
• /
• 1996

Usually triangular patches are used to transfer geometric shape in Rpaid Prototyping CAM system. STL, a list of triangles, is de facto in RP industry. Because STL has no topology data, it can cause errornous results. So, STL should be verified before using. After adding support structures to anchor the part to the platform and to prevent sagging or distortion, slicing and layer by layer manufacturing process are done. But triangular patch is surface model and cannot provide dufficient information on geometry in the above processes. So, geometric modeling is necessary in verifying STL, adding support structures, and slicing. It is natural that triangle based modeling is the best when traingular patches are used as input. Considering support structures, solid and faces coexist in RP process. Therefore non-manifold modeler is required. In this study, triangle based non-manifold geometric modeling is proposed for RP system consitent with STL input.

• Journal of the Korean GEO-environmental Society
• /
• v.18 no.2
• /
• pp.5-19
• /
• 2017

Underground excavation for building construction in Korea is changing from conventional support method (Strut, Ground anchor) to inside permanent support method by stability, economic, circumstances around excavation and etc. This study was selected the sites of Top-down, New Top-down, S.P.S, S.T.D and B.R.D in general use. This study was compared and analyzed a construction cost and period between aforementioned methods and conventional support method. Also, this study was confirmed the stability of temporary retaining wall by analysis for measurement data under construction. As a result, this study can grasp that most improved permanent support method is excellent in economic and constructability than conventional support method in case of deep excavation and rapid appearance of bedrock.