• Journal of Industrial Technology
• /
• v.21 no.A
• /
• pp.273-278
• /
• 2001

In this study, we prepared nano-sized $TiO_2$ particles for various process variables by the diffusion flame reactor and we collected $TiO_2$ particles by thermophoresis. It is found that the size of $TiO_2$ particles increases, as the flame temperature or the inlet $TiCl_4$ concentration increase or the total gas flow rate decreases. We investigated the photo-degradation of phenol wish the prepared $TiO_2$ particles. We found the optimum amounts of $TiO_2$ photocatalysts for our experimental apparatus and investigated the photo-degradation efficiencies of phenol, changing the process variables such as size of $TiO_2$ photocatlysts, phase ratio of rutile/anatase, concentration of phenol, input ratio of $O_2$. Degradation efficiencies of phenol were almost 95% in 15 minutes for the standard conditions of our experiments.

• Bulletin of the Korean Chemical Society
• /
• v.22 no.12
• /
• pp.1303-1308
• /
• 2001

A series of catalysts, NiSO4/TiO2, for ethylene dimerization was prepared by the impregnation method using aqueous solution of nickel sulfate. On the basis of the results obtained from X-ray diffraction, the addition of NiSO4 shifted the transition of TiO2 from the anatase to the rutile phase toward higher temperatures due to the interaction between NiSO4 and TiO2. Nickel sulfate supported on titania was found to be very active even at room temperature. The high catalytic activity of NiSO4/TiO2 closely correlated with the increase of acidity and acid strength due to the addition of NiSO4. It is suggested that the active sites responsible for ethylene dimerization consist of low valent nickel, Ni+, with an acid.

• Korean Journal of Metals and Materials
• /
• v.49 no.8
• /
• pp.596-600
• /
• 2011

Thermal degradation behavior of a $WO_3-TiO_2$ monolithic catalyst was investigated in terms of structural, morphological, and physico-chemical analyses. The catalyst with 4 wt.% $WO_3$ contents were prepared by a wet-impregnation method, and a durability test of the catalysts were performed in a temperature range between $400^{\circ}C$ and $800^{\circ}C$ for 3 h. An increase of thermal stress decreased the specific surface area, which was caused by grain growth and agglomeration of the catalyst particles. The phase transition from anatase to rutile occurred at around $800^{\circ}C$ and a decrease in the Brønsted acid sites was confirmed by structural analysis and physico-chemical analysis. A change in Brønsted acidity can affect to the catalytic efficiency; therefore, the thermal degradation behavior of the $WO_3-TiO_2$ catalyst could be explained by the transition to a stable rutile phase of $TiO_2$ and the decrease of specific surface area in the SCR catalyst.

• Journal of the Korean Ceramic Society
• /
• v.36 no.7
• /
• pp.742-750
• /
• 1999

Nanosized TiO2 powders were synthesized using the chemical vapor conduensation (CVC) process with various precursor feeding rates (0.37 and 0.752 ml/min) and oxygen flow rates(1-2slm) conditions and powder characteristics were investigated in terms of formation of nanosized powder varying with the above processing conditions. For this study the main thermodynamic and fluid dynamic factors -supersaturation ratio collision frequency and residence time-were theoretically established and compared to the characteristics of formed TiO2 powder. The loosely combined anatase phase powders (including less than 3%of rutile phase) having 20-30nm crystallite size were obtained at overall conditions. The particle size and th degree of agglomeration for a precursor flow rate of 0.376 ml/min turn out to be smaller than for a flow rate of 0.742ml/min. And the decreasing of particles size and particle size distribution were observed with increasing oxygen flow rate as the residence time and collision frequency were reduced by increasing oxygen flow rate,. It appears that further scrutiny is needed to elucidate the influence of the individual thermodynamic and kinetic parameters mdependently.

• Transactions of the Korean hydrogen and new energy society
• /
• v.22 no.4
• /
• pp.432-442
• /
• 2011

Anodized tubular $TiO_2$ electrodes (ATTEs) with three noticeably different lengths are prepared to determine their optimum length for the photo-driven activity in the reaction of Cr(VI) reduction and hydrogen evolution. The ATTEs with ethylene glycol have longer $TiO_2$ tubes (7-15.6 ${\mu}m$) than those with hydrfluoric acid (0.6-0.8 ${\mu}m$). These samples, which differ only in the length of the tubes, with a wall thickness of ca. 20 nm, consist mainly of an anatase crystalline phase after heat treatment at $650^{\circ}C$, since the anatase crystallites at the tube walls do not undergo transformation into rutile phase, due to the constraints imposed by the wall thickness. Among them, the medium size (ca. 8 ${\mu}m$) tubes provide the optimum conditions, irrespective of the light intensity, which is explained in terms of the correlation between the amount of photons and the adsorbed electron acceptors and their location. Photocatalytic Cr(VI) reduction leads to ca. 60% reduction of Cr(VI) even under 1 sun irradiation with the medium-sized anodized $TiO_2$ tubes, but only ca. 20% with the short- and long-sized tubes. For hydrogen evolution, tubes longer than 8 ${\mu}m$ do not exhibit better performance with any light intensity.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.5
• /
• pp.213-218
• /
• 2014

An investigation of the influence of $WO_3$ addition with different precursors and preparation methods on the phase formation and selective catalytic reduction (SCR) efficiency of anatase-$TiO_2$ powders has been carried out. An anatase-$TiO_2$ synthesized by precipitation process was used as a catalyst support. For $WO_3(10wt%)/TiO_2$, the W loading to the $TiO_2$ support led to the lower in anatase to rutile transition temperature to ${\sim}900^{\circ}C$ from $1200^{\circ}C$ of the $TiO_2$ support alone. In the case of $WO_3(10wt%)/TiO_2$ SCR powders obtained from a wet process with ammonium meta-tungstate (AMT) precursor, the highest $NO_X$ conversion efficiency was achieved at $450^{\circ}C$ remaining high efficiency at $500^{\circ}C$, while the same composition prepared from a dry process with $WO_3$ addition showed the lowered efficiency with temperature after reaching the efficiency maximum at $350^{\circ}C$. The same tendency has been found that the $V_2O_5(5wt%)-WO_3(10wt%)/TiO_2$ SCR powders obtained from the wet process with AMT precursor has shown the superior $NO_X$ conversion efficiency over 90 % in a wider temperature range of $300{\sim}500^{\circ}C$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.2
• /
• pp.846-849
• /
• 2013

Thin film of $TiO_2$ was obtained by the sol-gel dip method on the brosilicate glass substrate. It was found that the film was about $1.5{\mu}m$ thick as obtained by 4 successive coatings and annealed at varied temperatures ranged from $300^{\circ}C$ to $1100^{\circ}C$ for 2 hrs. The substrate used was having the surface area of $100mm^2$. Increasing the annealing temperature caused to change in mineralogical phase of titanium oxide i.e., amorphous, crystalline antase to rutile phases. The particle size of the titanium oxide film were ranged from $0.1{\sim}0.54{\mu}m$ estimated by the SEM analysis. The material showed an absorbance maximum at the wavelength 390nm obtained by UV-visible spectrophotometer. These results therefore, indicated that the $TiO_2$ film obtained relatively at low annealing temperature consisted predominantly with anatase phase; possessed higher photocatalytic behavior i.e., 2.4 times higher than that of only UV lamp irradiation.

• Journal of the Korean Ceramic Society
• /
• v.39 no.3
• /
• pp.252-258
• /
• 2002

Transparent $TiO_2$ thin films prepared by sol-gel process using the modification of titanium(IV) alkoxide showed improved thermal stability and high refraction index. Compared to the pure $TiO_2$ film, the modified $TiO_2$ films show the increased index of refraction under proper condition at pH 2.5. Transparency of these $TiO_2$ thin films were more than 80% in the visible region. It has been demonstrated that the reaction occurs in the amorphous phase: an exchange of phase results in anatase before and after 400$^{\circ}C$, in rutile over 700$^{\circ}$C form the XRD results. The particle sizes, shapes and structures of these nanoclusters in the $TiO_2$ films have been identified through a SEM and XRD. The physical properties and structures of their powders have also been studied through a SEM, XRD, TGA and DSC. The thickness and index of refraction have been determined by the analysis of ellipsometric spectra.

• Applied Chemistry for Engineering
• /
• v.28 no.5
• /
• pp.576-580
• /
• 2017

In the present paper, the thermal deactivation characteristics of plate-type commercial $V_2O_5-WO_3/TiO_2$ SCR catalyst were investigated. For this purpose, the plate-type catalyst was calcined at different temperatures ranging from $500^{\circ}C$ to $800^{\circ}C$ for 3 hours. Structural and morphological changes were characterized byXRD, specific surface area, porosity, SEM-EDS and also NOx conversion with ammonia according to the calcine temperature. The NOx conversion decreased with increasing calcine temperature, especially when the catalysts were calcined at temperatures above $700^{\circ}C$. This is because the crystal phase of $TiO_2$ changed from anatase to rutile, and the $TiO_2$ grain growth and $CaWO_4$ crystal phase were formed, which reduced the specific surface area and pore volume. In addition, $V_2O_5$, which is a catalytically active material, was sublimated or vaporized over $700^{\circ}C$, and a metal mesh used as a support of the catalyst occurred intergranular corrosion and oxidation due to the formation of Cr carbide.

• Elastomers and Composites
• /
• v.49 no.1
• /
• pp.53-58
• /
• 2014

In this study, characteristics of visible-light responsive photocatalyst Weltouch, especially VOCs reduction of visible-light responsive photocatalyst coated nylon/polyester composite fiber for vehicle interior parts and materials were evaluated. Visible-light responsive photocatalyst Weltouch was observed for both anatase phase and rutile phase. It is activated by light longer than 420nm. VOCs and formaldehyde generated from visible-light responsive photocatalyst treated nylon/polyester composite fiber were reduced confirmly. Visible-light responsive photocatalyst was firmly attached to the surface of nylon/polyester composite fiber without elimination even after 25 times repeated washing. And washing durability of nylon/polyester composite fiber confirmed the excellence that reduction effects of VOCs after repeated washing has appeared as much as before washing.