• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.2
• /
• pp.248-255
• /
• 2009

Error is the major problem in communication system. Absolute circuit is one of the most important building blocks to implement for the error measurement in communication system as well as in analog circuit design. The main goal of this paper is to design a circuit with high accuracy and minimum error performance. In this paper, a new current mode absolute circuit is implemented to calculate the absolute value of two signals. This new design shows enhanced performance and low distortion over the previous implementation. The proposed circuit is simulated using Hspice and implemented in analog viterbi decoder. It is very suitable for implementing in error calculation for the large scale integrated circuit. Hspice simulation results of previous and new one circuit are reported.

• Journal of Advanced Navigation Technology
• /
• v.23 no.2
• /
• pp.179-185
• /
• 2019

In this paper, we have studied narrow-band analog pre-distortion linearization technique using UHF 400 MHz band 20 W power amplifier. The analog pre-distorter used the SC1894 radio frequency power amplifier linearizer(RFPAL) provided by MAXIM Corp and through the look-up table technique confirmed the intermodulation distortion(IMD) performance and the adjusted channel leakage ratio(ACLR) improvement for bandwidth below 1 MHz which does not operate on existing chips. In the 400 MHz (400 ~ 500 MHz) band, IMD performance and the ACLR improvement of up to 17.46 dB based on 1-channel offset and up to 16.6 dB based on 2-channel offset were confirmed. In the system requiring the same linearity, we confirmed power efficiency improvement of 12.41% at output power of over 40 W.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.5
• /
• pp.447-453
• /
• 2006

This paper proposes that 5 phase step motor drive system has high performance utilizing a micro step control with a current controller. Also this paper proposes an analog current controller to minimize size of the 5 phase step motor drive system. It has better advantages of cost and noise and heating than commercial products. As a result, Applying this system to position control robot the validity of suggested analog current controller and driver system is verified.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.10 no.4
• /
• pp.132-137
• /
• 2007

The dynamic range of the radar which uses digital signal processors is limited by ADC(Analog-to-Digital Converter). That parameter and ADC loss depend on the noise level of radar receiver. In order to stabilize the performance of radar systems, it is necessary to maintain the noise level constantly. This paper presents the noise AGC(Automatic Gain Control) concept that can keep the noise level constantly and proves that the concept is acceptable through the hardware test and evaluation.

• IE interfaces
• /
• v.10 no.2
• /
• pp.15-28
• /
• 1997

Knowledge acquisition has been a major bottleneck in building expert systems. To ease the problems arising in knowledge acquisition, analog concept learning systems(ACLS) has been used. In this paper, in order to avoid the overfitting problem and secure a good performance, we propose the revised ACLS, which pruning methods -cost complexity, reduced error, pessimistic pruning and production rule- are incorporated into and apply them to the credit evaluation for Korean companies. The performances of the revised ACLS are evaluated in light of the prediction accuracy. To check the effect of the training data sampling on the performance, experiments are conducted using the different proportion of the training data. Experimental results show that the revised ACLS of combining cost complexity pruning with reduced error pruning performs best among original ACLS and other methods.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.37 no.11
• /
• pp.786-795
• /
• 1988

In this paper a boiler control system simulator is designed and inplemeted in order to evaluate performance of the Fault Tolerant Control System. It simulates a boiler control system of a thermal power plant containtng boiler process, peripheral units and analog controller. The simulator uses a low order linear model for boiler first order models for the peripheral unit. Specifically the model of the analog controller is modularized and transformed to digital form if order to be implemented using a micro-processor board. The experimental results show the usability of the developed simulator for the performance test of the FTCS.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.8
• /
• pp.2043-2054
• /
• 1996

In this paper, Digital Delay Locked Loop(DDLL) is designed, implemented and analysed by experiment whose results show that it is possible to track the received signal by this scheme. Designed digital DLL has an advantage that it is not needed to maintain gain balance between early and late channels, which has been problem with an analog DLL. Also DDLL has more improved noise performance compared to analog DLL due to noise level limitation and noise cancellation characteristics. For various loop parameters, their effects on loop performance are analysed and simulated. Proposed DDLL is the first attempt as a digital approach in code tracking loop and it is expected to be a good reference for spread spectrum communication research.

• Journal of Power System Engineering
• /
• v.9 no.4
• /
• pp.155-161
• /
• 2005

Governors control the revolution speed of heat engines such as diesel engines, steam turbines and gas turbines. Precise and prompt tests for the control performances of governors are essential both in governors' manufacturing processes and in governors' maintenance processes. In the conventional governor test systems controlled by analog type electronic controllers, the incorporation of heat engine's dynamics to the test system have been considered very difficult to realize. This study suggests a new governor test system controlled by a digital controller using a personal computer. The application of the digital controller to the test system instead of the analog type electronic controller have brought about the following advancements; (1) heat engine's dynamics could be implemented easily in the test system, (2) automatic test data acquisition both in steady state and in transient state enables us to save test time and to enhance the reliability of the tests.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.52 no.11
• /
• pp.657-661
• /
• 2003

In this paper, we designed a portable digital pressure algometer which not only can measure the pain level objectively and quantitatively, but also is able to do RF communication. This system consists of pressure sensor for pain measurement, analog signal analysis, digital hardware based on PIC16C73B, RF communication and display. To evaluate the performance of the developed system, we measured pressure threshold using commercial analog PA(Pressure Algometer) and the proposed system, and then evaluated the correlation and confidence. Using linear regression analysis, standard deviation of 0.1731 and R-square value of 99.3% were obtained. In conclusion, the above results showed good performance and its usability in measuring the pain clinically.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.1
• /
• pp.10-19
• /
• 1990

A fault tolerant control system, in which a digital back-up controller system is added on the existing analog control system, is developed for enhancing reliability of boiler control system in power plant. The digital back-up controller system(DBCS) has a multi-processor structure with capabilities of fault diagnosis, back-up control, self test, and graphic monitoring. Specifically, switching mechanism composed of expandable modules is designed so that back-up controller takes over any faulty control loops and the number of back-up control loops is determined as that of simultaneous faults. A process simulator that simulates the boiler analog control system is developed for safety test and performance evaluation prior to real plant application. DBCS is installed at the Ulsan thermal power plant, and fault tolerant control performance is assured under the faults that some controller modules are pulled out.