• Advances in materials Research
• /
• v.13 no.3
• /
• pp.153-160
• /
• 2024

This study investigates the application of alternating current (AC) and direct current (DC) anodization techniques on stainless steel 304L (SS304L) in an ethylene glycol and ammonium fluoride (NH4F) electrolyte solution to produce a nano-porous oxide layer. With limited research on AC anodizing of stainless steel, this study focuses on comparing AC and DC anodization in terms of current density versus time response, phase analysis using X-ray diffraction (XRD), and corrosion rate determined by linear polarization. Both AC and DC anodization were performed for 60 minutes at 50 V in an electrolyte solution containing 0.5% NH4F and 3% H₂O in ethylene glycol. The results show that AC anodization exhibited higher current density compared to DC anodization. XRD analysis revealed the presence of ferrite (α-Fe) and austenite (γ-Fe) phases in the as-received specimen, while both AC and DC anodized specimens exhibited only the γ-Fe phase. The corrosion rate of the AC-anodized specimen was measured at 0.00083 mm/year, lower than the corrosion rate of the DC-anodized specimen at 0.00197 mm/year. These findings indicate that AC anodization on stainless steel offers advantages in terms of higher current density, phase transformation, and lower corrosion rate compared to DC anodization. These results highlight the need for further investigation and exploration of AC anodization as a promising technique for enhancing the electrochemical properties of stainless steel.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.13 no.3
• /
• pp.147-151
• /
• 2009

Purpose: 2-[$^{18}F$]Fluoro-2-deoxy-D-glucose ([$^{18}F$]FDG) particularly plays as a important role in Positron Emission Tomography (PET) imaging in nuclear medicine. Domestic [$^{18}F$]FDG auto synthesizers are installed in Seoul National University Bundang Hospital (SNUBH) at June 2008, these modules were known that it's synthetic yields were guaranteed in average $45{\pm}5%$ so far. To improve yields and convenience of domestic [$^{18}F$]FDG auto synthesizer, numerous trials in reaction time, base concentration, pressure and temperature were performed to increase [$^{18}F$]FDG yields. Materials and Methods: Several synthetic factors (temperature, time and pressure) and shortcoming were corrected based on many evaporation test. Syringe dispensing of tetra-butylammonium bicarbonate (TBAB) was replaced with micro pipette to prepare tetrabutyl ammonium fluoride salt ([$^{18}F$]TBAF). Troublesome refill of liquid nitrogen every 2 hours which was used to protect vacuum system was changed to charcoal cartridge, base guard filter. To monitor the volume of delivered $[^{18}O]OH_2$ from cyclotron by surveillance camera, we set up the volumetric vial on the cover of the module. In addition to, the recovery vial was added in [$^{18}F$]FDG production system to recover [$^{18}F$]FDG loss due to the leak of valve ($V_{13,14}$) in [$^{18}F$]FDG purification process. Results: When we used micro pipette for adding TBAB ($30\;{\mu}L$ in 12% $H_2O$ in acetonitrile), this quantitative dispensation has enabled to improve $5.5{\pm}1.7%$ residual fluorine-18 activity in fluorine separation cartridge compared to syringe adding. Besides, the synthetic yields of [$^{18}F$]FDG has increased $58{\pm}2.6%$ (n=19), $58{\pm}2.9%$ (n=14), $60%{\pm}2.5%$ (n=17) for 3 months. The life cycle of charcoal cartridge and base vacuum was 3 months prior to filling liquid nitrogen every 2 hours and additional side separator can prevent pump corrosion by organic solvent. After setting of volumetric indicator vial, the operator can easily monitor the total volume of irradiated $[^{18}O]OH_2$ from cyclotron. The recovery vial can be used for the stabilizer when an irregular [$^{18}F$]FDG loss was generated by the leak of valves ($V_{13,14}$). Conclusions: We has optimized appropriate synthetic conditions (temperature, time, pressure) in domestic [$^{18}F$]FDG auto synthesizer. In addition to, the remodeling with several accessories improve yields of domestic [$^{18}F$]FDG auto synthesizer with reliable reproducibility.

• Journal of Microbiology and Biotechnology
• /
• v.25 no.11
• /
• pp.1944-1953
• /
• 2015

A novel alkaline protease from Streptomyces sp. M30, SapHM, was purified by ammonium sulfate precipitation, hydrophobic interaction chromatography, and DEAE-Sepharose chromatography, with a yield of 15.5% and a specific activity of 29,070 U/mg. Tryptic fragments of the purified SapHM were obtained by electrospray ionization quadrupole time-of-flight mass spectrometry. Nucleotide sequence analysis revealed that the gene sapHM contained 1,179 bp, corresponding to 392 amino acids with conserved Asp156, His187, and Ser339 residues of alkaline protease. The first 24 amino acid residues were predicted to be a signal peptide, and the molecular mass of the mature peptide was 37.1 kDa based on amino acid sequences and mass spectrometry. Pure SapHM was optimally active at 80℃ in 50 mM glycine-NaOH buffer (pH 9.0), and was broadly stable at 0-50℃ and pH 4.0-9.0. The protease relative activity was increased in the presence of Ni²⁺, Mn²⁺, and Cu²⁺ to 112%, 113%, and 147% of control, respectively. Pure SapHM was also activated by dimethylformamide, dimethyl sulfoxide, Tween 80, and urea. The activity of the purified enzyme was completely inhibited by phenylmethylsulfonyl fluoride, indicating that it is a serine-type protease. The K_m and V_max values were estimated to be 35.7 mg/ml, and 5 × 10⁴ U/mg for casein. Substrate specificity analysis showed that SapH was active on casein, bovine serum albumin, and bovine serum fibrin.

• Membrane Journal
• /
• v.14 no.2
• /
• pp.108-116
• /
• 2004

In this study, the pore-filled ion-exchange membranes were prepared by using the asymmetric PVDF membrane as a nascent membrane. First, the solution of PVBCI having the chlorornethylate aryl ring of 80 percents and DABCO was made with the mixed solvent of THF and DU (8:2). These mixed solution was then, filled in the pores of PVDF membrane, and left for a day to complete the gelation. Finally the pore-filled anion-exchange membrane is obtained fallowed by the amination of the remaining chloromethyl groups with trimethylamine (TMA, 40 wt% in water) forming the positive ammonium ion sites. This 2 step procedure enabled us to produce the pore-filled membranes without change of size, and to control the properties of final membrane with various degree of cross-linking. The results of SEM and AFM showed the polyelectrolyte existed in the pores of nascent membrane as a certain configuration. From the investigation of the solvent affecting much to the permeability and rejection, it was found that the membranes using mixed solvent of THE and DMF (8:2) showed better performances than the membranes produced by THF only. The result of an investigation for the water permeability of the final membrane at low pressure (100 Kpa) showed a typical ultrafiltration membrane's permeability (8 ∼ 10 kg/$m^2$hr) and good values of rejection (55∼60 percent).

• Applied Chemistry for Engineering
• /
• v.32 no.3
• /
• pp.290-298
• /
• 2021

A purification process was performed for the application of natural graphite as an anode material. The influence of the structural change and impurity content of graphite according to the process on the anode electrochemical characteristics was investigated. Natural graphite was chemically/physically purified by acid-treatment which used different amounts of solution of ammonium fluoride/sulfuric acid in the same ratio and thermal treatment used different temperatures (800~2500 ℃). Acid-treatment had limitation to remove impurities, and identified that all impurity contents was removed except some traces of atom such as Si by after progressed thermal-treatment until 2500 ℃. The anode materials characteristic of graphite treated by purification process was improved, and changes in the structure and impurity contents affected dominantly the capacity, rate property and initial Coulombic efficiency. Consequently, the complex purification process improved the graphite structure and also the performance of lithium ion battery by controlling the excessive formation of solid electrolyte interphase and expanding Li⁺ insertion space originated from the effective removal of impurities.

• Korean Journal of Soil Science and Fertilizer
• /
• v.32 no.1
• /
• pp.47-56
• /
• 1999

$^{15}N$-Isotope concentrations of groundwater from l4 wells with different land-use types in Kyonggi Province were measured to investigate the nitrate contamination sources. Water samples were collected monthly from January to December 1997 and analyzed for pH. PC, anions (fluoride, chloride, nitrate, sulfate, inorganic phosphate, and bicarbonate), and canons (calcium, magnesium, potassium, and sodium). For the analysis of the $^{15}N/^{14}N$ ratio as ${\delta}^{15}N$, $N_2$ samples were prepared through Kjeldahl-Rittenberg method and were analyzed using an isotope ratio mass spectrometer (VG Optima IRMS). Reproducibility of the method and precision of the IRMS were below 1.0‰ and 0.1‰, respectively. The ionic composition of each groundwater sample was only slightly different according to the land-use type. The nitrate concentrations of groundwater in cropland or livestock farming areas were higher than those in the residential area. The percentages of nitrate to total anions of groundwater samples from the livestock farming area were higher than those of other areas. The ${\delta}^{15}N$ values of ammonium sulfate, urea, groundwater sample in the non-contaminated area, and water from the animal manure septic tank were -2.7, 1.4, 5.5, and 27.2‰, respectively. Based on the ${\delta}^{15}N$ values, the sources of nitrate could be classified as originated from chemical fertilizers with ${\delta}^{15}N$ values below 5% and as from animal manure or municipal waste with ${\delta}^{15}N$ values over 10‰. In most cases, contamination sources investigated from ${\delta}^{15}N$ values of groundwater samples were correlated with the specific sources according to the land-use types. However, some ${\delta}^{15}N$ values did not matched the apparent land-use types, and there were seasonal variations of ${\delta}^{15}N$ values within the same well. These results suggest that the groundwater quality was affected by two or more contamination sources and the contribution of each source to the groundwater quality varied depending on the sampling season.

• Korean Journal of Agricultural Science
• /
• v.16 no.2
• /
• pp.225-238
• /
• 1989

These studies were conducted to investigate the extraction, purification and characterization of oriental pear (Niitaka. Pyrus pyrifolia Nak.) protease, and the results obtained were as follows: 1. Oriental pear protease was effectively extracted by the method of homogenizing pear pulp with 0.7 volume of 0.1M-sodium phosphate buffer, pH 6.5 containing 5mM-cysteine, 40mM-2-mercaptoethanol and 2mM-EDTA at 10,000 rpm for 5 min. 2. The protease was purified by ammonium sulfate fractionation, Sephadex G-100 filtration and DEAE-Sephadex A-50 column chromatography, and the purified enzyme gave a single protein band on polyacrylamide gel electrophoresis. 3. The specific activity of purified enzyme was 29.65 unit/mg protein and the yield was 7.22%. 4. The moecular weight of the protease was estimated to be about 51,000 by SDS-polyacrylamide gel electrophoresis, and the enzyme had Km value of 54.5 mg/ml for casein. 5. The purified enzyme had a maximum activity at pH 6.0 and $50^{\circ}C$, and was stable from pH 5.5-6.5 and at temperatures below $50^{\circ}C$ 6. Casein was a better substrate for this protease compared to hemoglobin. 7. The enzyme activity was markedly inhibited by p-chloromercuribenzoic acid and heavy metal salts such as $HgCl_2$ and $MnSO_4$ also considerably inhibited the enzyme activity.