• Journal of Korean Society for Atmospheric Environment
• /
• v.21 no.5
• /
• pp.507-513
• /
• 2005

Increasing amounts of anthropogenic $CO_2$ emitted to the atmosphere are believed to be a significant factor in global climate change. Hence, the method of chemical absorption has been suggested to separate and recover acid gases such as $CO_2$. In this study, the characteristics of absorption and regeneration of $CO_2$ for the absorbent which adding HMDA (hexamethylenediamine) into AMP (2-amino-2-methyl-1-propanol), hindered amine, was investigated in lab-scale absorption/regeneration reactor. As a result of this study, the removal efficiency of $CO_2$ increased when adding $5.9\%,\;11.7\%\;and\;23.4\%$ HMDA into $30\%$ AMP respectively. Also, the removal efficiency of $CO_2$ increased $6.5\%,\;8.4\%,\;10.3\%$ respectively as compared to AMP alone when the gas flow rate was 7.5 SL/min. In addition, all absorbents used in the study revealed the high stripping efficiency, which was almost $99\%$, at the temperature of $110^{\circ}C$. Thus, the regeneration tower should be operated at $110^{\circ}C$. At this time, the concentration of exhausted $CO_2$ was higher than $99\%$.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.25 no.1
• /
• pp.14-20
• /
• 2016

This paper describes a green stripping process to effectively strip the remaining DFR layer on a non-alkali-based ITO glass surface after an etching process. A stripper, water-soluble amine compound, is used to investigate the characteristics of stripping ability and to suggest a valid method for the green process. Increasing the composition (5-30% concentration) of the ethanol amine-based stripper was found to greatly reduce the stripping time applied in the dipping method. The composition (30%) achieved an excellent stripping effect and free-residue impurities. Additionally, it was possible to obtain the effect of stripping in a way to sustain the release before generating DFR sludge from the ITO glass surface by using dipping condition (stripping time) in the composition. An Additional stripping process (buffering) out of dipping can realize productivity improvement and cost reduction because of the higher proportion of re-use of the stripping solution used in the DFR removal step.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.7
• /
• pp.457-463
• /
• 2013

The removal of sulfonamide antibiotics (SAs) by activated carbon was investigated by using granular activated carbon (GAC) tests and density functional theory (DFT) simulations. The GAC absorption tests show the removal efficiency of 68.4~90.7% and 99.0~99.9% in 1 and 24 hours, respectively. In both GAC tests, the removal efficiency of sulfamethazine (SMZ) was the highest followed by those of sulfathiazole (STZ) and sulfamethoxazole (SMTZ): SMZ > STZ > SMTZ. In DFT adsorption simulations, we found that the 4-aminobenzenesulfonamide parts of SMZ and STZ and the 3-methyl-1,2-oxazol-5-amine part of SMTZ are preferentially adsorbed on the edges of graphene model, provided that the adsorbates keep their structures without dissociation upon adsorption process. The adsorption energies of SMZ, STZ, and SMTZ are -4.91, -4.64, and -4.62 eV, respectively. This adsorption strength (SMZ > STZ > STMZ) agrees with the trend of the removal efficiency of SAs by GAC. In addition, dissociative adsorption configurations of SAs are discussed.

• Nuclear Engineering and Technology
• /
• v.52 no.11
• /
• pp.2652-2659
• /
• 2020

The methyl iodide (CH₃I) removal performance of tri-ethylene-di-amine impregnated activated carbon (TEDA-AC) used in the air cleaning unit of nuclear power plants (NPPs) should be maintained at least 99% between 24 month-performance test period. In order for evaluating the effectiveness of TEDA-AC on the removal performance of CH₃I in nuclear power plant during the operation of NPPs, the long-term test for up to 15 months was carried out under the simulated operating conditions (e.g., 25 ℃, RH 50%, ppb level poisoning gases injection) at nuclear power plants (NPPs). The TEDA-AC samples were analyzed with the Brunauer-Emmett-Teller (BET) specific surface area and TEDA content as well as CH₃I penetration test. It is clearly evident that more than 99% of CH₃I removal performance of TEDA-AC was observed in the TEDA-AC samples during 15 months of long-term operation under the simulated NPP operating conditions including the ppb level of organic and oxide form of poisoning gases. BET specific surface area and TEDA content that can affect the CH₃I removal performance of TEDA-AC were also maintained as those in new TEDA-AC during 15 months of long-term operation.

• Korean Chemical Engineering Research
• /
• v.44 no.2
• /
• pp.172-178
• /
• 2006

Mesoporous silicate materials have been used as adsorbents for the removal of heavy metals from water by introducing functional groups such as thiol and amine. In this research, it was investigated whether surfactants used as templating agents in synthetic processes can act as adsorption sites for heavy metals. Three mesoporous silicates-SBA-15, MCM-41, and HMS were synthesized using, respectively, block copolymer, hexadecyltrimethylammoniumbromide (HDTMA), and dodecyamine as surfactants. X-ray diffraction and $N_2$ gas adsorption analysis confirmed that the mesoporous silicates were well prepared and FT-IR spectra resulted in the existence of the surfactants in as-synthesized mesoporous silicates and the removal of surfactants after calcination. The interactions between $Pb^{2+}$ ions and the mesoporous silicate materials with/without surfactants were observed. In adsorption kinetic experiments, it revealed that the calcined mesoporous silicates and the surfactant-loaded SBA-15 almost had no adsorption capacity for $Pb^{2+}$ ions. In contrast, the surfactant-loaded MCM-41 and HMS showed, respectively, the adsorption capacities of 26.60 and 115.16 mg/g which were acquired through the fits of adsorption kinetic data to the pseudo second order kinetic model. The adsorption capacities were comparable to those of other mesoporous adsorbents for heavy metals.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.9
• /
• pp.913-917
• /
• 2008

Since the difficulty of analysis at low concentration and the uncertainty of the removal mechanism for Nitrosodimethylamine (NDMA) have been reported, this study has detected extremely low concentration $^{14}$C-NDMA using the LSC(Liquid Scintillation Counter) and tested NDMA removal by Powdered Activated Carbon(PAC). The results showed the highest correlation over 99% when samples were measured with the mixture ratio of sample to scintillation liquid of 10 : 10 and at the detection time of 10 min. For $^{14}$C-NDMA removal by the PACs(S-A(Sigma-Aldrich co.) and Dj(Daejung co.)) raging from 50$\sim$10,000 mg/L, $^{14}$C-NDMA was removed over 90% by adsorption treatment. In addition, S-A showed twice greater adsorption capacity than that of Dj. However, the required PAC amount for $^{14}$C-NDMA removal was higher than that of other amine compounds.

• Korean Chemical Engineering Research
• /
• v.50 no.1
• /
• pp.128-134
• /
• 2012

The pilot scale experiments can handle the flue gas up to 1,000 $Nm^3/hr$ for separation of carbon dioxide included in real flue gas at coal-fired power plant. The operational characteristics was analyzed with the main experimental variables such as flue gas flow rate, absorbent circulation rate using chemical absorbents mono-ethanolamine( MEA) and 2-amino-2-methyl-1-propanol(AMP). The more flue gas flow rate decreased in 100 $m^3/hr$ in the MEA 20 wt% experiments, the more carbon dioxide removal efficiency was increased 6.7% on average. Carbon dioxide removal efficiency was increased approximately 2.8% according to raise of the 1,000 kg/hr absorbent circulation rate. It also was more than 90% at $110^{\circ}C$ of re-boiler temperature. Carbon dioxide removal efficiency of the MEA was higher than that of the AMP. In the MEA(20 wt%) experiment, carbon dioxide removal efficiency(85.5%) was 10% higher than result(75.5%) of ASPEN plus simulation.

• KSBB Journal
• /
• v.25 no.5
• /
• pp.421-428
• /
• 2010

This paper reports on the experimental investigation carried out to evaluate the physical optimal conditions in the absorption column to remove odorous hydrogen sulfide gas. Hydrogen sulfide gas, as a highly undesirable contaminant, is most widely emitted from environmental treatment facilities. The absorbent mixed with natural second metabolites extracted from conifer trees and chemical absorbent of 2-aminoethanol was applied to remove it via chemical neutralization. The absorbent of natural second metabolites was achieved by a removal efficiency of 20-40% by itself depending on the treatment conditions, but the complex absorbent mixed with 0.1% amine chemical provides the removal efficiency of 98%. The optimal removal efficiencies have been examined against the two major parameters of temperature and pH. This study shows that the aqueous solution by natural second metabolites can be used as an appropriate absorbent in the column absorbed for the removal of hydrogen sulfide gas.

• Journal of Environmental Science International
• /
• v.12 no.4
• /
• pp.497-501
• /
• 2003

The new tridentate ligands of nitrogen donor atoms N,N-Bis(2-amino-ethyI)-benzyl-amine 2HCI(BABEA. 2HCI) and 2,6-Bis(amino-methyl)-pyridien. 2HCI(BAMP. 2HCI) were synthesized as their dihydrochloride salts and characterized by TA, IR. Mass and NMR spectroscopy. The protonation constants of the ligands and stability constants for Cd$^{2+}$, Pb$^{2+}$, Zn$^{2+}$and Cu$^{2+}$ ions were determined by potentiometric titration in aqueous solutions and compared with those of analogous ligands. The effect stability constants of ligands and metal ions for removal of heavy metals in aqueous solution were described.

• Textile Coloration and Finishing
• /
• v.1 no.1
• /
• pp.26-34
• /
• 1989

The selective chemical degradation or etching of PET based on an organic amine attack on the ester group. The techniques involves the chemical removal of loss ordered amorphous regions or crystalline regions, which are essentially unaffected by the degradative etchant. Thus, most of previous studies have limited to consideration which has been given to structural changes taking place. Therefore, this study was carried out to investigate surface characterization, dyeing properties of PET film hydrazinolyzed with hydrazine hydrate in methanol. PET film was treated with 30% hydrazine hydrate in methanol at $30^\circ{C}$ for various time intervals. The total surface tension of treated PET increased, the dispersion force decreased and the hydrogen bonding force increased. The equilibrium dye adsorption, dyeing rate and apparent diffusion coefficient of acid dyes increased, and the apparent activation energies of diffusion decreased.