• 소성∙가공
• /
• 제30권4호
• /
• pp.179-185
• /
• 2021

Lithium ion batteries are generally manufactured by laser and etching using aluminum thin sheet. These processes are relatively expensive and have low productivity. In this study, blanking process of aluminum thin sheet for lithium ion battery was employed to replace laser cutting and etching process, all to reduce the production cost and improve productivity. Mechanical properties for aluminum and coating were determined by experimental results and rule of mixture for FE analysis of blanking process. Normalized Cockcroft-Latham criteria was also applied to describe shear behavior and critical damage values were determined by comparison of analytical and experimental result. We performed FE analysis to investigate the effects of clearance and punch-die radius on sheared surface of aluminum thin sheet and to determine optimal process condition. We manufactured the die set using the determined optimal process and conducted an experiment to confirm the feasibility of blanking process. The sheared surface of manufactured product was observed by optical microscope. As a results, the proposed process conditions successfully achieved the dimensional requirement in production of lithium ion battery parts.

• International Journal of Automotive Technology
• /
• 제6권3호
• /
• pp.259-268
• /
• 2005

In order to analyze the sheet drawability, the measurement of the plastic strain ratio was carried out for the 5182 aluminum alloy sheets in which were cold rolled without lubrication and subsequent recrystallization annealing. The average plastic strain ratio of the 5182 aluminum sheets was 1.50. It was considered that the higher plastic strain ratio was resulted from the ND//<111> component evolved during rolling and maintained during annealing. The AA5182/polypropylene/AA5182 (AA/PP/AA) sandwich sheets of the 5182 aluminum alloy skin sheet and the polypropylene core sheet with high formability have been developed for application for automotive body panels in future light weight vehicles with significant weight reduction. The AA/PP/AA sandwich sheets were fabricated by the adhesion of the core sheet and the upper and lower skin sheets. The AA/PP/AA sandwich sheet had high plastic strain ratio (1.58), however, the planar anisotropy of the sandwich sheet was little changed after fabrication. The optimum combination of directionality of the upper and lower skin sheets having high plastic strain ratio and low planar anisotropy was calculated theoretically and an advanced process for producing the sandwich sheets with high plastic strain ratio was proposed. The developed sandwich sheets have a high average plastic strain ratio of 1.55 and a low planar anisotropy of 0.17, which was improved more by 3.2 times than that of 5182 aluminum single sheet.

• 소성∙가공
• /
• 제9권1호
• /
• pp.27-34
• /
• 2000

Sheet metal formabilities for aluminum 1050 and 5052 were experimentally investigated in this study. Deep drawability, bendability and stretch formability were measured at each process condition and correlated with tensile properties of sheet metal. To compare the formabilities of aluminum 1050 and 5052 sheets with those of steel sheets, deep drawing quality(DDQ) steel sheets are also tested at the same test conditions. Through the experimental studies, influential process variables for each forming process were obtained and correlated with the tensile properties. The comparisons of sheet metal formabilities with those of steed sheets showed that aluminum 1050 and 5052 is inherently deficient in formability than steel sheets but Al 5052 that has highter n and r value than al 1050 showed better formabilities.

• 소성∙가공
• /
• 제7권6호
• /
• pp.603-609
• /
• 1998

An aluminium sandwich sheet is the material fabricated by adhering two aluminum panels to one plastic core. When it has the same bending stiffness as an steel panel it is 65% lighter than steel panel and 30% lighter than aluminum panel. Therefore it is notified exclusively as good substitutive materials for steel body to improve fuel efficiency. An aluminium sandwich sheet, however, has a problem of the lower formability than steel in automotive application. In this paper we intend to develop application technologies of an aluminum sandwich sheet for auto body panels from selecting composed materials of aluminium sandwich sheets to fabricating prototype. We selected aluminium sandwich panels fabricated by Hoogovens company. Through formability tests we have designed the hood part on auto body panels and fabricated a mould and a prototype.

• 대한기계학회논문집A
• /
• 제36권4호
• /
• pp.413-420
• /
• 2012

알루미늄 포일 접착강판은 접착제를 이용하여 알루미늄 포일을 드로잉용 GI 강판 위에 접착시킨 강판이다. 알루미늄 포일의 박리현상은 알루미늄 포일 강판의 주된 성형불량 중의 하나이다. 본 연구에서는 가전제품의 외관에 활용되는 알루미늄 포일 접착강판의 박리한계를 규명하였다. 알루미늄 포일 접착강판의 박리는 알루미늄 포일과 강판의 접착강도에 의해 결정된다. 알루미늄 접착강판의 박리와 접착강도와의 관계를 분석하기 위해 CZM 을 활용하여 알루미늄 포일 접착강판의 계면접착력에 따른 알루미늄 포일 박리변형률의 변화를 분석하였다. 해석결과, 박리발생의 주원인은 강판의 변형 중 접착계면에서 발생하는 전단응력에 의해 박리가 발생함을 확인하였다. 또한 알루미늄 포일 접착강판의 계면접착력을 측정하여 강판의 등이축인장모드인 스트레치 변형에 따른 박리가 발생하는 한계변형률을 도출하였다. 도출된 알루미늄 포일 접착강판의 박리 한계는 에릭슨 시험을 통해 검증하였다.

• Journal of Welding and Joining
• /
• 제15권4호
• /
• pp.42-62
• /
• 1997

Resistance spot welding has been widely used in the sheet metal joining processes because of its high productivity and convenience. Recently, automobile industries are trying to replace partly steel sheets with aluminum alloy sheets. Among currently produced aluminum alloys, Al alloy sheets of Al-Mg-Si(6000 series) are being tested. Especially, 6000 series are the most probable substitute in view of strength and weldability. In this paper, an attempt was made to apply resistance spot welding to joining of dissimilar sheet metals (KS6383+SCPZn or KS6383+SHCP). An effort was made to balance heating rate in the Al alloy with that in the steel sheets by increasing electrode tip diameter. Although resistance spot welding of Al alloy sheet and sheet metals does not produce desirable nugget, it proved to have reasonable strength if optimal weld condition is found by tensile-shear strength and fatigue life test. Since spot weld joints in automobile are always experiencing repeated load, spot welding methodology proposed in this paper is found to be not suitable to automobile body manufacturing.

• International Journal of Automotive Technology
• /
• 제6권6호
• /
• pp.657-663
• /
• 2005

Recently, weight reduction of vehicles has been of great interest, and consequently the use of composite materials in the automotive industry is increasing every year. Composite sandwich panels which consist of two skins and core materials are replacing steels in automotive floor and door. The substitution of one material for another is accompanied by change of joining method, so that adhesive bonding has been popularly used for joining method of composite materials. In the case of adhesive bonding of composite materials, there could be loss in the joint strength by delamination of two faceplates or cracking on faceplate. Thus, it is necessary to prevent loss in the joint strength by designing the joint geometry. In the present paper, adhesive bonding of aluminum sandwich sheet was tried. For understanding joint behavior, studies on stresses in the single lap joint were reviewed and failure modes of composite material were analyzed. Strength tests on the single lap joint consisting of aluminum sandwich sheet and steel were performed and variation of the joint strength with the joint configuration was shown. Based on these results, design guide of adhesive bonding in aluminum sandwich sheet was suggested.

• 한국수산과학회지
• /
• 제50권4호
• /
• pp.388-395
• /
• 2017

We investigated the toxicity of zinc and aluminum hot-dip galvanized sheet steel to abalone Haliotis discus hannai via changes in the gill and hepatopancreas using histological and transmission electron microscopy analysis. Experimental groups were composed of one control and four exposure conditions (direct or indirect exposure to zinc and aluminum hot-dip galvanized sheet steel). In the control group, aluminum exposure groups (direct and indirect), and indirect zinc exposure group, abalone mortality was not observed until the end of the experiment, and no histopathological changes were observed in the gill and hepatopancreas. However, the direct zinc exposure group exhibited 100% mortality. Ultrastructural analysis of the cytoplasm of ciliated and microvilli-bearing epithelial cells from gill filaments revealed electron-dense vesicles near the cell membrane and disruption of the nuclear membrane. We also observed swollen mitochondria and a loss of mitochondrial cristae. The hepatopancreas showed similar changes, and we detected highly electron-dense particles within the vesicles. These results suggest that abalone exposed directly to zinc hot-dip galvanized sheet steel experience acute toxicity, causing damage to cell organelles in the gill and hepatopancreas and, finally, inducing mortality.

• 한국해양공학회지
• /
• 제25권1호
• /
• pp.44-48
• /
• 2011

Researchers suggested painted coating characteristics of aluminum sheet by various sending condition. Painted coating is used to protect the surface of the blocks from the interior and exterior. It is also used to enhance the value of automobiles and ship materials. This process makes the materials surface for protection and elegance. Although analysis of the roughness and critical scratch load of painted coating is important, the effects of this material have not progressed much. In this study, the characteristics of painted coating in the other conditions of the polished aluminum sheet were investigated. The results of both various conditions and initial roughness values were almost similar to final values after painted coating.

• 소성∙가공
• /
• 제8권3호
• /
• pp.252-261
• /
• 1999

The 3-dimensional finite element program is developed to analyze the non-isothermal forming processes of aluminum-alloy sheet metals. Bishop's method is introduced to solve the heat balance and force equilibrium equations. Also, Barlat's non-quadratic anisotropic yield function depicts the planar anisotropy of the aluminum-alloy sheet. To find an appropriate constitutive equation, four different forms are reviewed. For the verification of the reliability of the developed program, the computational try-outs of the non-isothermal cylindrical cupping processes of AL5052-H32 and Al1050-H16 are carried out. As results, the constitutive equation relating to strain and strain-rate, in which the constants are represented by the 5th-degree polynomials of temperature, is in good agreement with measurement. The computational try-outs can predict optimal forming conditions in non-isothermal forming processes.