• Journal of Powder Materials
• /
• v.11 no.3
• /
• pp.247-252
• /
• 2004

Recently, it has been found that mechanical alloying (MA) facilitates the nanocomposites formation of metal-metal oxide systems through solid-state reduction during ball milling. In this work, we studied the MA effect of Fe$_{3}$O$_{4}$-M (M = Al, Ti) systems, where pure metals are used as reducing agents. It is found that composite powders in which $Al_{2}$O$_{3}$ and TiO$_{2}$ are dispersed in $\alpha$-Fe matrix with nano-sized grains are obtained by mechanical alloying of Fe$_{3}$O$_{4}$ with Al and Ti for 25 and 75 hours, respectively. It is suggested that the large negative heat associated with the chemical reduction of magnetite by aluminum is responsible for the shorter MA time for composite powder formation in Fe$_{3}$O$_{4}$-Al system. X-ray diffraction results show that the reduction of magnetite by Al and Ti if a relatively simple reaction, involving one intermediate phase of FeAl$_{2}$O$_{4}$ or Fe$_{3}$Ti$_{3}$O$_{10}$. The average grain size of $\alpha$-Fe in Fe-TiO$_{2}$ composite powders is in the range of 30 nm. From magnetic measurement, we can also obtain indirect information about the details of the solid-state reduction process during MA.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.5
• /
• pp.1579-1582
• /
• 2011

Alumina particles wrapped in few-layer graphene sheets were prepared by calcining aluminum nitride powders under a mixed gas flow of carbon monoxide and argon. The graphene sheets were characterized by powder X-ray diffraction (XRD), Raman spectroscopy, electron energy loss spectroscopy, and high-resolution transmission electron microscopy. The few-layer graphene sheets, which wrapped around the alumina particles, did not exhibit any diffraction peaks in the XRD patterns but did show three characteristic bands (D, G, and 2D bands) in the Raman spectra. The dye-sensitized solar cell (DSSC) with the alumina particles wrapped in few-layer graphene sheets exhibited significantly improved overall energy-conversion efficiency, compared to conventional DSSC, due to longer electron lifetime.

• Journal of the Korean Ceramic Society
• /
• v.29 no.12
• /
• pp.956-962
• /
• 1992

The predominant sintering mechanisms of low firing temperature ceramic substrate which consists of borosilicate glass containing alumina as a filler are the rearrangement of alumina particles and the viscous flow of glass powders. In this system, sintering condition depends on the volume ratio of alumina to glass and on the particle size. When the substrate contains about 35 vol% alumina filler and the average alumina particle size is 4 $\mu\textrm{m}$, the best firing condition is obtained at the temperature range of 900∼1000$^{\circ}C$. The extensive rearrangement behavior occurs at these conditions, and the optimum sintering condition is attained by smaller size of glass particles, too. The formation of cristobalite during sintering causes the difference of thermal expansion coefficient between the substrate and Si chip. This phenomenon degradates the capacity of Si chip. Therefore, the crystallization should be prevented. In the alumina filled borosilicate glass system, the crystallization does not occur. This effect may have some relation with aluminum ions in alumina. For aluminum ions diffuse into glass matrix during sintering, functiong as network former.

• Journal of Pharmaceutical Investigation
• /
• v.3 no.1_2
• /
• pp.34-50
• /
• 1973

There are many reports on the stability of drugs in powders and tablets. The stabilities of ascorbic acid in the antacid preparations, such as calcium carbonate, magnesium carbonate, magnesium trisilicate, magnesium alumino silicate, and dried aluminum hydroxide gel under various humidities were examined. From the result of the experiment, it was assumed that the concentration of ascorbic acid, the amount of water-vapor sorption, and the physical character of the antacid ingredients were the main factors, influencing the degradation of ascorbic acid. The ascorbic acid, mixed with carbonates, such as calcium carbonate, was degradaded rapidly, while the preparation with dried aluminum hydroxide gel was slightly degraded after 10 days. A 2% ascorbic acid in the prepation was rapidly degraded than 10% ascorbic acid in the preparation.

• Journal of the Korean institute of surface engineering
• /
• v.25 no.3
• /
• pp.150-157
• /
• 1992

A recovery process of pure alumina powder from the wasted aluminum etching solution of electrolytic condenser works was studied. The possibility of this process was considered in the basis of thermodynamic data nad physico-chemical properties for the recovered materials were tested. In order to obtain pure alumina, Fe3+ and Cu2+ in the solution as impurities were solvent-extracted, respectively, and then, Al3+ was precipitated by changing the pH of the solution. As the results, more than 99.9% of Al3+ in the solution was recovered by the precipitation method. The weight of the precipitate was reduced to about 65 wt.% of the original one by calcination and the sizes of the recovered powders were in order of 3-5$\mu\textrm{m}$. The precipitates were transformed to $\alpha$-Al2O3 at the calcination temperature about 120$0^{\circ}C$.

• Geomechanics and Engineering
• /
• v.10 no.1
• /
• pp.109-124
• /
• 2016

In this paper, process of dynamic powder compaction is investigated experimentally using impact of drop hammer and die tube. A series of test is performed using aluminum powder with different grain size. The energy of compaction of powder is determined by measuring height of hammer and the results presented in term of compact density and rupture stress. This paper also presents a mathematical modeling using experimental data and neural network. The purpose of this modeling is to display how the variations of the significant parameters changes with the compact density and rupture stress. The closed-form obtained model shows very good agreement with experimental results and it provides a way of studying and understanding the mechanics of dynamic powder compaction process. In the considered energy level (from 733 to 3580 J), the relative density is varied from 63.89% to 87.41%, 63.93% to 91.52%, 64.15% to 95.11% for powder A, B and C respectively. Also, the maximum rupture stress are obtained for different types of powder and the results shown that the rupture stress increases with increasing energy level and grain size.

• Journal of Powder Materials
• /
• v.23 no.3
• /
• pp.195-201
• /
• 2016

Composite materials consisting of pure aluminum matrix reinforced with different amounts of graphite particles are successfully fabricated by mechanical ball milling and spark plasma sintering (SPS) processes. The shrinkage rates of the composite powders vary with the amount of graphite particles and the lowest shrinkage value is observed for the composite with the highest amount of graphite particles. The current slopes of time increase with increase in the amount of graphite particles whereas the current slopes of temperature show the opposite trend. The highest thermal conductivity is achieved for the composite with the least amount of graphite particles. Therefore, the thermal properties of the composite materials can be controlled by controlling the amount of the graphite particles during the SPS process.

• Nuclear Engineering and Technology
• /
• v.39 no.5
• /
• pp.617-626
• /
• 2007

A centrifugal atomization process for uranium fuel was developed in order to fabricate high uranium density dispersion fuel for advanced research reactors. Spherical powders of $U_3Si$ and U-Mo were successfully fabricated and dispersed in aluminum matrices. Thermal and mechanical properties of dispersion fuel meat were characterized. Irradiation tests at the research reactor HANARO confirm the excellent performance of high uranium density dispersion fuel.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.4
• /
• pp.167-172
• /
• 2013

Titanium dioxides nanoparticles coated aluminum oxide powders were fabricated by pulsed laser deposition (PLD) with Nd : YAG laser at 266 nm. The Pulse laser energy is 100 mJ/pulse. During the irradiation of the focused laser on the $TiO_2$ target, Ar gas is supplied into the chamber. The gas pressure is varied in a range of $1{\times}10^{-2}$ to 100 Pa. Titanium dioxides nanoparticles deposited aluminum oxide powders were characterized by using energy dispersive X-ray spectroscopy (EDX), high resolution transmission electron microscopy (HR-TEM), in order to understand the effect of Ar background gas on surface morphology and properties of the powders. The coated $TiO_2$ nanoparticles had nanosized spherical shape and the crystallite sizes of 10~30 nm. The morphology of coated $TiO_2$ nanoparticles is not affected by gas pressure. However, the particle size and crystallinity slightly increased with the increase of gas pressure. According to this technique, the size and crystallinity of nanoparticles can be easily controlled by controlling pressure during the laser irradiation.

• Resources Recycling
• /
• v.10 no.4
• /
• pp.42-47
• /
• 2001

Recycling of aluminum dross is a significant issue in domestic aluminum industry. In this study, formed ceramic materials were prepared using aluminum dross mixed with feldspar powders to investigate its application as industrial materials and utilization of aluminum dross. In the prepared sample, feldspar was melted at the sintered temperature, and its phase was trans-formed into amorphous, and spinel ($MgA1_2$$O_4$) phase in the dross was remained clearly. Density of the test specimen Increased from 0.91 to 0.65 gr/㎤ and water absorbance decreased from 2.5 to 1.7f% with increasing of sintered time at the sintered temperature $1220^{\circ}C$ with composition of feldspar 55 wt%, dross 40wt% and bentonite 5 wt%. At the same experimental conditions, bending strength of the test specimen was 10.8 MPa, and heat conductivity was 0.34 W/m.K with sintered time 30 minutes.