• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1994년도 특별강연 및 춘계학술발표 개요집
• /
• pp.222-225
• /
• 1994

The weldability of aluminum is excel lent but weld metal is subject to include weld defects such as porosities, crack, incomplete penetration and incomplete fusion because of improper welding parameters. Especially, the porosities are main weld defects because the difference of hydrogen solubility change in melt ins and solidification state with temperature changing. Deformation of aluminum is larger than mi Id steel due to higher thermal conductivity. It is reported that porosities in deposited metal affect tensile strength and elongation. Therefore, the effect of groove angle on porosities and mechanical properties of weld metal were researched in this report where Al-5083 plate was used with 5356 filler metal that are excellent anti corrosion and strength.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 춘계학술발표대회 개요집
• /
• pp.174-176
• /
• 2005

On the basis of successful experiences and data from author's past experimental results of friction stir welding on thin aluminum plates, thick aluminum plate of high strength 2000 series has been carried out in this study. For various combination of rotating speed, welding speed and tool (RIWRC38-C) shape, the butt welded specimens has been prepared to check the metallurgical characteristics, hardness distributions and defects. From the results, feasible welding conditions have been obtained as 450 rpm rotating speed and 5 mm/min welding speed. Using these optimum welding parameters, 38.1mm-thickness A2519-T87 plates have been FSWelded in single pass. A good weld surface appearance and defects free weld zone has been observed in X-ray inspection. Softened region has been generated by dissolution of precipitates and coarsened microstructure in the stir zone after FSWeld.

• 한국표면공학회지
• /
• 제13권2호
• /
• pp.81-86
• /
• 1980

The mechanical properties of aluminized steel were investigated after the JIS SB 41 plates were dipped in molten aluminum bath. (1) The growth rate of iron-aluminum alloy layer was fast in early stage of alumizing, and then gradually decreased with increasing time. However, over the time period above 10 minutes the growth of alloy layer did not occur. (2) The constituent of alloy layer formed on the steel surface was identified to be intermetallic compound of $Fe_2\;Al_5$. (3) The ultimate tensile strength and elongation of aluminized steel showed a nearly constant value over all thickness below about 0.15 mm. However, both properties decreased rapidly in showed a nearly constant value over all thickness above about 0.20 mm. (4) In case of aluminized steel with greater thickness, crack was formed below yield point of base metal, which is considered to be attributed to the alloy layer failure.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 추계학술발표대회 논문집
• /
• pp.63-66
• /
• 2000

This research addresses study on thermal residual stress of a composite patch repair of the edge cracked aluminium panel of aging aircraft. Composite patch repair is an efficient and economical technique to improve the damage tolerance of cracked metallic structures. These are thermal residual stresses due to the mismatch of coefficient of thermal expansion, and these are affected by the curing cycle of patch specimen. In this study, three curing cycles were selected for F.E. analysis. This study features the effect on composite patch and aluminum by thermal residual stress during crack propagation in aluminum plate.

• Nuclear Engineering and Technology
• /
• 제45권7호
• /
• pp.979-986
• /
• 2013

Uranium metal particle dispersion plates have been proposed as targets for Molybdenum-99 (Mo-99) production to improve the radioisotope production efficiency of conventional low enriched uranium targets. In this study, uranium powder was produced by centrifugal atomization, and miniature target plates containing uranium particles in an aluminum matrix with uranium densities up to 9 $g-U/cm^3$ were fabricated. Additional heat treatment was applied to convert the uranium particles into UAlx compounds by a chemical reaction of the uranium particles and aluminum matrix. Thus, these target plates can be treated with the same alkaline dissolution process that is used for conventional $UAl_x$ dispersion targets, while increasing the uranium density in the target plates.

• 한국주조공학회지
• /
• 제7권2호
• /
• pp.122-132
• /
• 1987

Full mold casting process is a new technique offering numerous advantages and promising possibilities. The present study is aimed to bring out the results of experiments carried out to study the effect of pattern coatings on the solidification of 99.5% pure aluminum plate-shaped castings in the various sand molds and the thermal behavior of the molds. The results of the investigation indicate that (i) with increase in pattern coating thickness, the relative chilling power decreases gradually for silica and increases for zircon coating, and (ii) the application of a pattern coating significantly reduces the maximum interface temperature by the mold which is more pronounced in the case of thinner mold wall. The investigation also indicates that Chvorinov's rule is not found to be valid for the casting in the full mold, with or without pattern coating. Therefore in full mold process, the pattern coating thickness will be a very important parameter in the study of thermal behavior.

• Coupled systems mechanics
• /
• 제2권3호
• /
• pp.271-288
• /
• 2013

In the present study an elastic-plastic strain analysis is carried out for fibrous composites by using numerical modeling. Application of homogeneous transversely-isotropic model was chosen based on problem solution of a square plate with a circular hole under uniaxial tension. The results obtained in this study correspond to the solution of fiber model trial problem, as well as to analytical solution. Further, numerical algorithm and software has been developed, based on simplified theory of small elastic strains for transversely-isotropic bodies, and FEM. The influence of holes and cracks on stress state of complicated configuration transversely-isotropic bodies has been studied. Strain curves and plasticity zones that are formed in vicinity of the concentrators has been provided. Numerical values of effective mechanical parameters calculated for unidirectional composites at different ratios of fiber volume content and matrix. Content volume proportions of fibers and matrix defined for fibrous composite material that enables to behave as elastic-plastic body or as a brittle material. The influences of the fibrous structure on stress concentration in vicinity of holes on boron/aluminum D16, used as an example.

• 한국전기전자재료학회논문지
• /
• 제36권3호
• /
• pp.298-302
• /
• 2023

In this paper, we discussed the effect of field plate dielectric materials such as silicon dioxide (SiO₂), aluminum oxide (Al₂O₃), and hafnium oxide (HfO₂) on the breakdown characteristics of β-Ga₂O₃ Schottky barrier diodes (SBDs). The breakdown voltage (BV) of the SBDs with a field plate was higher than that of SBDs without a field plate. The higher dielectric constant of HfO₂ contributed to the superior reduction in electric field concentration at the Schottky junction edge from 5.4 to 2.4 MV/cm. The SBDs with HfO₂ field plate showed the highest BV of 720 V, and constant specific on-resistance (R_on,sp) of 5.6 mΩ·cm², resulting in the highest Baliga's figure-of-merit (BFOM) of 92.0 MW/cm². We also investigated the effect of dielectric thickness and field plate length on BV.

• 한국소음진동공학회논문집
• /
• 제13권10호
• /
• pp.777-784
• /
• 2003

본 논문에서는 압전소자를 이용한 코너 지지된 직사각형 박판의 음향 반응에 대한 제어에 관하여 이론과 실험적인 연구를 하였다. 3개의 각각 다른 종횡비의 알루미늄판을 사용하였고 고정은 4개의 코너에서 볼조인트를 이용하였다. 그 결과 종횡비가 가장 큰 박판에서 0∼200Hz 진동수와 80∼100dB의 음압의 가진에서 예측대로 가장 크고 선명한 응답을 보였다. 압전소자에 의한 판을 통한 음향전달 감소는 크지 않았지만, 압전소자를 이용한 음향반응 제어는 기대 이상으로 현저하였다. 본 실험은 항공기 승강문의 음장 가진에 대한 선행 연구를 확장시킨 독창적인 연구이다. 가장 중요한 차이점은 문의 조인트를 볼 조인트로 모사한 것이다.

• 수산해양교육연구
• /
• 제19권1호
• /
• pp.129-136
• /
• 2007

The component parts of the shell plate of a ship are steel. but the screw propeller or the bow thruster is a compound of bronze, nickel and aluminum. On account of the these different components between metals of the shell plate, the screw propeller and the bow thruster, which are underwater, the shell plate of a ship is corroded by the action of ionization. Authors investigated the corrosion loss of the zinc anodes which were attached to the bottom shell of the training ship Kaya for about two years. The obtained results were as follows:1. In case of the shell plate the difference of the corrosion loss according to port and starboard was almost nothing. But the corrosion loss of the forward part was more than that of the aftward part.2. There was little difference in the corrosion loss between the forward and the aftward part on the bilge keel.3. The corrosion loss of the fore, midship and aft part on the false keel were 24.7%, 22.4% and 23.9% respectively.4. The corrosion loss of the fore and the aft part on the false keel was more than that of the midship part.5. The corrosion loss of the bow thruster was greater than any other parts.6. The nearer the zinc anode to the screw propeller the more the corrosion loss on the stern frame, and the situation was also same as on the rudder.