• Journal of Korean Society of Water and Wastewater
• /
• v.24 no.4
• /
• pp.463-474
• /
• 2010

In this study, chemical coagulation conditions for treating combined sewer overflow(CSO) occurred during rainy season were evaluated by jar tests with aluminum sulfate[$Al_2(SO_4)_3{\cdot}17H_2O$] and ferric chloride[$FeCl_3{\cdot}6H_2O$]. The raw domestic sewage sampled from the primary sedimentation tank at a local sewage treatment plant was filtered through $150{\mu}m$ sieve before using. Point of zero charge(PZC) for various dose of aluminum sulfate occurred at pH 5.8-6.5, while for ferric chloride occurred at pH 5.3-6.0 in term of streaming current(SC) values. Charge neutralization ability of aluminum sulfate was bigger than that of ferric chloride. Optimum pH and dose of aluminum sulfate and ferric chloride were 6.2, 0.438mM and 5.8, 0.925mM, respectively. Removal efficiencies of TCOD, turbidity, SS and TP were 75, 97, 95, 96% with aluminum sulfate and 74, 96, 98, 99% with ferric chloride at their optimum coagulation conditions. More efficient removal of SS, TP and small particles was possible with ferric chloride at optimum coagulation conditions. Both SC values and COD removal started to increase where soluble phosphorus was completely removed.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.50 no.4
• /
• pp.388-395
• /
• 2017

We investigated the toxicity of zinc and aluminum hot-dip galvanized sheet steel to abalone Haliotis discus hannai via changes in the gill and hepatopancreas using histological and transmission electron microscopy analysis. Experimental groups were composed of one control and four exposure conditions (direct or indirect exposure to zinc and aluminum hot-dip galvanized sheet steel). In the control group, aluminum exposure groups (direct and indirect), and indirect zinc exposure group, abalone mortality was not observed until the end of the experiment, and no histopathological changes were observed in the gill and hepatopancreas. However, the direct zinc exposure group exhibited 100% mortality. Ultrastructural analysis of the cytoplasm of ciliated and microvilli-bearing epithelial cells from gill filaments revealed electron-dense vesicles near the cell membrane and disruption of the nuclear membrane. We also observed swollen mitochondria and a loss of mitochondrial cristae. The hepatopancreas showed similar changes, and we detected highly electron-dense particles within the vesicles. These results suggest that abalone exposed directly to zinc hot-dip galvanized sheet steel experience acute toxicity, causing damage to cell organelles in the gill and hepatopancreas and, finally, inducing mortality.

• Journal of Powder Materials
• /
• v.26 no.5
• /
• pp.383-388
• /
• 2019

To improve the mechanical properties of aluminum, graphene has been used as a reinforcing material, yielding graphene-reinforced aluminum matrix composites (GRAMCs). Dispersion of graphene materials is an important factor that affects the properties of GRAMCs, which are mainly manufactured by mechanical mixing methods such as ball milling. However, the use of only mechanical mixing process is limited to achieve homogeneous dispersion of graphene. To overcome this problem, in this study, we have prepared composite materials by coating aluminum particles with graphene by a self-assembly reaction using poly vinylalcohol and ethylene diamine as coupling agents. The scanning electron microscopy and Fourier-transform infrared spectroscopy results confirm the coating of graphene on the Al surface. Bulk density of the sintered composites by spark plasma sintering achieved a relative density of over 99% up to 0.5 wt.% graphene oxide content.

• Applied Chemistry for Engineering
• /
• v.18 no.6
• /
• pp.636-642
• /
• 2007

Software program to predict the packing density of multi-sized and multi-component particulate system was developed. For this purpose, the experiment to measure the packing density of AP (ammonium perchlorate) and Al (aluminum) particles with different sizes and their mixtures was carried out. The packing densities obtained from various experiments were compared with the predicted data from the developed software program. In the case of the packing density of the binary system, which is comprised of two different size particles and/or two different components, the relative errors were ranged 0.25~13.13%, and in the same venue the relative errors of the ternary system were 0.25~13.13%. Agreement between experimental data and the predicted results is reasonably accurate. In order to achieve the targeted packing density, the software program calculated the contour of the component particles and this will contribute the formulation of optimal packing systems.

• Journal of Welding and Joining
• /
• v.22 no.5
• /
• pp.46-52
• /
• 2004

AlSi-Al$_2$O$_3$ composite layer was prepared by plasma spray on steel substrate. The composite powder for plasma spray was prepared by simple mechanical blending. The wear resistance of the composite layers and matrix aluminum alloy were performed in terms of size distribution of ceramic particles. Friction coefficients of AlSi were decreased with incorporation of $Al_2$O$_3$. The tribological properties of coated layers were affected by the size of incorporated $Al_2$O$_3$ particle. The reinforcement of $Al_2$O$_3$ particle into aluminum alloy matrix decreased the friction coefficient as well as wear loss.

• Journal of Welding and Joining
• /
• v.17 no.6
• /
• pp.62-69
• /
• 1999

The advantages of Thermal sprayed coatings as a replacement for cast iron liners are reduced weight, better heat transfer and reduced cost. One of the most important performance attributes of a cylinder bore coating is its wear resistance, since it must survive the abrasive sliding of both the piston rings and the piston skirt. In this study, composite powders were prepared by ball milling of Al-13Si-3Mg(wt%) alloy with SiC particles. The concentrations of SiC were 40 and 60wt%. The composite powders were sprayed using Metco-9MB plasma torch. Plasma sprayed coatings were heat-treated at 500℃ for 3 hours. The wear resistances of the plasma sprayed coatings were found to improve with heat treatment and superior to the commercially available G.C.I.(gray cast iron). AlSiMg-40SiC heat-treated coatings showed the best wear resistance in this study.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1303-1304
• /
• 2006

The type, volume fraction, size, shape and arrangement of embedded particles influence the mechanical properties of the particle reinforced metal matrix composites. This presents the investigation of the SiC particle and porosity distributions in various aluminum matrix composites produced by cold- and hot-pressing. The microstructures were characterized by optical microscopy and stereological parameters. SiC and porosity volume fractions, and the anisotropy distribution function were measured to establish the influence of the consolidation method.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.1164-1167
• /
• 2003

Recently CRT is getting flatted, As change of CRT trend from normal type to Flat type, the material of Shadow Mask was also changed from AK(Aluminum Killed) to Invar(Fe-Ni alloy) materials Until now we have used just AK(Aluminum Killed) for normal type TV(not flat type), but main raw material of shadow mask component was changed. . However recently Invar(Fe-Ni alloy) materials, which has advantage of Low Thermal Expansion and High Strength, has been developed as well as applying in mass production as CRT's trend has become more flat and fine pitch. As main raw material of shadow mask component was changed, conditions of process were changed. One of them, the importance of pre-etching process (assistant process for developing & etching) is improved because there are so many particles in the pre-etching bath because of Ni compounds. Since the solubility of Ni in pre-etching solvent is very low related to Fe's, so the compounds of Ni happen to make particles.(the solubility of Fe is twenty times Ni's) that particles happen to make process troubles and NG productions so to clear the particles we had to established high cost filtering system, but it is useless. As time goes by the quantity of particles (Ni compounds) was increased because of the capability of filtering system was not enough, the particles was produced continuous in bath, and it make quality problems. Hence we tried to develop the new pre-etching solution to remove the particles (Ni compounds) and to cost down the filtering system's running cost. But in improving the solution we discovered the new pre-etching solution made the PR developing better. In former solution there were three kinds of chemistry (COOH)2 , H2O2 , H2S04 .first the function of (COOH)2 is drilling the surface of Invar, during this mechanism Ni compounds occurred. Second the function of H202 is removing the PR fringe (half UV exposure zone on PR(PVA)), Third the function of H2S04 is the catalysis of (COOH)2 In those, (COOH)2 was the main reason to make the Ni compounds. So to improve the solutions we had to change (COOH)2 to the other material. the chemistry we improved was a complex chemistry based on H2S04 . after using this chemistry the particles problem was disappeared and there was another advantage cut down the PR fringe. The New solution made the function of H202 better so the PR developing improved. To be direct the catalyst of the new solution helped the H202. anyway First thing after change the solution the quality of shadow Mask for flat color TV was improved & the yield also improved. But the more important thing is how to control the new solution. So we accepted the new concept which was the degree of freshness. The degree of freshness is based on non-reacted solution which was 100% ( the degree of freshness) and calculated the melted Ni quantity as time goes by. So we made the gauging liner plot. In conclusion, many companies tried to make fine pitched Shadow Mask ,generally to make quality jump up it needed a lot of cost & persons .in this case the shift of core material made it possible.

• Korean Journal of Materials Research
• /
• v.22 no.9
• /
• pp.445-449
• /
• 2012

We investigate the effects of redox reaction on preparation of high purity ${\alpha}$-alumina from selectively ground aluminum dross. Preparation procedure of the ${\alpha}$-alumina from the aluminum dross has four steps: i) selective crushing and grinding, ii) leaching process, iii) redox reaction, and iv) precipitation reaction under controlled pH. Aluminum dross supplied from a smelter was ground to separate metallic aluminum. After the separation, the recovered particles were treated with hydrochloric acid(HCl) to leach aluminum as aluminum chloride solution. Then, the aluminum chloride solution was applied to a redox reaction with hydrogen peroxide($H_2O_2$). The pH value of the solution was controlled by addition of ammonia to obtain aluminum hydroxide and to remove other impurities. Then, the obtained aluminum hydroxide was dried at $60^{\circ}C$ and heat-treated at $1300^{\circ}C$ to form ${\alpha}$-alumina. Aluminum dross was found to contain a complex mixture of aluminum metal, aluminum oxide, aluminum nitride, and spinel compounds. Regardless of introduction of the redox reaction, both of the sintered products are composed mainly of ${\alpha}$-alumina. There were fewer impurities in the solution subject to the redox reaction than there were in the solution that was not subject to the redox reaction. The impurities were precipitated by pH control with ammonia solution, and then removed. We can obtain aluminum hydroxide with high purity through control of pH after the redox reaction. Thus, pH control brings a synthesis of ${\alpha}$-alumina with fewer impurities after the redox reaction. Consequently, high purity ${\alpha}$-alumina from aluminum dross can be fabricated through the process by redox reaction.

• Journal of Environmental Health Sciences
• /
• v.17 no.1
• /
• pp.67-73
• /
• 1991

In this study are investigated to the optimal coagulation conditions and magnetite which was used as coagulation-aids. To accomplish this study, analysis of water quality, removing tubidity and SS from wastewater were measured with jar-tester. The results were obtained that waste water requires 10g magnetite, 100mg aluminum sulfate, and pH valuse was 6~9.