• Journal of Korea Society of Industrial Information Systems
• /
• v.22 no.5
• /
• pp.31-37
• /
• 2017

In this Paper, we have Improved the Manufacturing Process of Liquid Aluminum Sulfate using the Design of Automated Measurement Systems. The Manufacturing Process of Liquid Aluminum Sulfate uses a Large Weight. The Quality of a Product Depends Highly on the Proportion of the Raw Material Input in the Production Process. Therefore, it is Very Important to Accurately Measure the Amount of Raw Material. For Automation Design, Load Cell Sensor which can Measure Large Weight Accurately and PLC Technology which is most used in Automation Process are Applied. The Content of Aluminum Oxide in the Aluminum Sulfate Produced before the Automation Design Varies from 8.023% to 8.250%. However, after Automation Design, the Amount of Change from 8.09% to 8.19% was Greatly Reduced. As a Result, we could Reduce the Quality Defect rate Due to Weighing Errors and Reduce Safety Accidents by Applying Automation System.

• Journal of the Korean institute of surface engineering
• /
• v.37 no.1
• /
• pp.13-21
• /
• 2004

The deposition rate, the current efficiency and surface morphology of trivalent Cr deposits were investigated according to additives in sulfate bath and current density. The deposition rate of the Cr deposits plated from the formic acid complexed bath was noticeably higher than that of the glycine complexed bath. The current efficiency of the deposition from formic acid bath was higher than that of the glycine bath and increased with current density in the range of 20-50 A/d$\m^2$. The current efficiency of the deposition from the formic acid bath with boric acid buffer was higher than that of the bath with aluminum sulfate or boric acid-aluminum sulfate buffers. The nodular crystallite size of the Cr deposits increased with current density and the uniform and crack-free growth of the deposits for the aluminum sulfate was observed compared to the other buffers.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.04a
• /
• pp.215.1-215
• /
• 2003

• Horticultural Science & Technology
• /
• v.17 no.6
• /
• pp.758-760
• /
• 1999

This experiment was carried out to investigate the effect of pretreatments and holding solutions on quality and vase life of cut 'Saphir' rose (Rosa hybrida L.). Pulsing with aluminum sulfate or NaOCl prolonged vase life held in HQS+sucrose+ethionine. Solution absorption held in distilled water were more increased than held in HQS+sucrose+ethionine. Holding solution with 8-hydroxyquinoline sulfate (HQS)+sucrose+ethionine increased fresh weight compared with distilled water except pulsing with STS+sucrose. Pulsing with aluminium sulfate delayed bent-neck held in HQS+sucrose+ethionine. Flower diameter and dry weight of petal held in HQS+sucrose+ethionine were more increased than held in distilled water except pulsing with STS+sucrose. There were no significance in Hunter color value 'L' and value 'a', but value 'b' was decreased held in distilled water.

• Journal of Environmental Science International
• /
• v.31 no.1
• /
• pp.1-8
• /
• 2022

In this study, solid-liquid separation conditions for coagulation and sedimentation experiments using inorganic coagulant (aluminum sulfate and Poly-Aluminum Chloride (PAC)) were optimized with brine wastewater discharged by the epoxy-resin process. When the turbidity and suspended solid (SS) concentration in raw wastewater were 74 NTU and 4.1 mg/L, respectively, their values decreased the lowest in a coagulant dosage of 135.0 - 270.0 mg Al³⁺/L. The epoxy resin was re-dispersed in the upper part of wastewater treated above 405.0 mg Al³⁺/L. The removal efficiencies of turbidity and SS via dosing with aluminum sulfate and PAC were evaluated at initial turbidity and SS of 74 - 630 NTU and 4.1 - 38.5 mg/L, respectively. They increased most in the range from 135.0 - 270.0 mg Al³⁺/L. The solid-liquid separation condition was quantitatively compared to the correlation of SS removal efficiency between the coagulant dosage and SS concentration based on the concentration of aluminum ions. The empirical formula, R = be^aD, shows the relationship between SS removal efficiency (R) and coagulant dosage (D) at 38.5 mg/L; it produced high correlation coefficients (r²) of 0.9871 for aluminum sulfate and 0.9751 for PAC.

• Journal of the Korean Wood Science and Technology
• /
• v.16 no.1
• /
• pp.3-8
• /
• 1988

This study was carried out to examine the effect of pretreatment of veneer with aluminum sulfate solution for the manufacture of the kapur plywood on the reduction of urea resin spread. The results were as follows: 1. Specific gravities of plywoods made of the kapur veneers ranged from 0.83 to 0.84 and their moisture contents based on air dry weight showed from 10.6% to 11.4%. These met the Korean Industrial Standards. 2. In the case of dry shear strength for the 3rd class plywood, 40% reduction- spread met K S as well as normal urea resin spread. pH of the aluminum sulfate solution gave better result at pH 4.5 and pH 6 than at pH 3. For the manufacture of the 2nd class plywood, hot and cold water-wet shear strength show the best results at the following conditions; such as 20% reduction spread, pH 4.5 of aluminum sulfate solution and all veneer treatment.

• Journal of the Korean Ceramic Society
• /
• v.26 no.1
• /
• pp.81-90
• /
• 1989

High purity alumina and amorphous silica were prepared from Ha-dong kaolin by means of appliance of sulfuric acid. The effect of sulfuric acid concentration, reaction temperature and reaction time on the formation of aluminum sulfate was investigated. The precipitation conditions ofaluminum sulfate from the sulfuric acid solution with ethanol and ammonium hydroxide were deteremined. In the optimum condition, the conversion of aluminum oxide in kaolin to aluminum oxide powder was 85.0 percent. Alumina powder was prepared by calcination of the precipitates, and its purity was 99.0 percent.

• Journal of Korean Society of Water and Wastewater
• /
• v.18 no.3
• /
• pp.331-336
• /
• 2004

The correlation between polymeric aluminum species of coagulant and its coagulation efficiency was investigated using several commercial polymeric Al(III) inorganic coagulants (Poly Aluminum Hydroxy Chloro Sulfate 2020 (PAHCS2020), Poly Aluminum Hydroxy Chloro Sulfate 2500 (PAHCS2500) which was introduced in Korean water treatment plants. The poly aluminum chloride (PAC), Poly Aluminum Hydroxide Chloride Silicate (PACS)) and the aluminum salts ($AlCl_3$, Alum ($Al_2(SO_4)_3$)) were used for the purpose of comparison. The comparison of the coagulation efficiency of each coagulant was made by turbidity removal through the standard jar testing procedure and the determination of the hydrolytic Al(III) species was made by the ferron method which can differentiate the monomeric aluminum species from the polymeric aluminum species. Overall, PAHCS2020 and PAHCS2500 showed the better performance in turbidity removal than the aluminum salts. The performance of coagulation was even better without adjustment of pH during the coagulation experiment. The positive correlation between polymeric aluminum species of coagulant and coagulation efficiency was found.

• Journal of the Korean Ceramic Society
• /
• v.27 no.6
• /
• pp.747-754
• /
• 1990

Aluminum hydrate gels were prepared from the mixtures of bauxite and ammonium sulfate by wet acid process. Optimum conditions for obtaining the maximum yield( 99%) of aluminum hydrates from the same amount of bauxite were confirmed as follows ; 1. Mixing ratio ; addition of 25mole% of ammonium sulfate to 1mole of bauxite. 2. Calcination ; heated at 350℃ for 1hr. 3. Extraction ; leached at 95℃ in 1% H2SO4 for 90min. 4. pH of precipitating solution; slight below 7.0. Amorphous aluminum hydrates were precipitated at the pH lower than 8.5, but the precipitates crystallized to bayerite at the pH was 10. Mean diameter of α-Al2O3 powders which were obtained by calcining the aluminum hydrates was below 0.2㎛, and EDS analysis revealed than SiO2 was it's primary impurity.

• Journal of Environmental Science International
• /
• v.8 no.6
• /
• pp.711-716
• /
• 1999

This research explored the feasibility of preparing and utilizing a prefonned polymeric solution of Al(III) for coagulation in water treatment. Slow base(NaOH) injection into supersaturated aluminum chloride and aluminum sulfate solutions did produce high yields of Al polymers useful to water treatment applications. The method of characterization analysis was based on timed spectrophotometer with ferron as a color developing reagent. The hydrolytic Al species were divided into $monomeric(Al_a),\;polymeric(Al_b),\;and\;precipitate(Al_c)$ from the difference in reaction kinetics. The analysis of PACl's characteristics showed that the quantity of polymeric Al produced at value of$ r(OH_{added}/AI)=2.2$ was $83\%$ of the total aluminum in solution, as showing maximum contents and precipitated Al was dramatically increased when r was increased above 2.35. In addition, the characteristics of polyaluminum sulfate (PAS) showed that polymeric Al contained at r = 0.75 was $18\%$ of the total aluminum in solution. The synthesized PACI and PAS were stable during storing period, as indicating negligible aging effect. The effect of sulfate ion on PACI was dependent on the concentration of sulfate ion. That is, polymeric species decrease and precipitate species increase as sulfate ion concentration increased. It can be concluded that the sulfate cause the formation of $Al(OH)_{3(S)}$ at low pH. However, The effect of calcium ion was negligible for distribution of Al species.