• 한국결정성장학회지
• /
• 제9권3호
• /
• pp.320-326
• /
• 1999

금속 Al과 산화물{{{{{Al}_{2}{O}_{3}}}}}를 사용하여 Al의 직접질화법에 의한 ALON 합성실험을 행하여 Al의 첨가량의 변화에 따른 질화반응 거동과 ALON 반응소결체의 특성을 조사하였다. Al과{{{{{Al}_{2}{O}_{3}}}}}의 직접질화법에 의한 ALON 합성이 가능함을 확인하였다. 소결온도가 증가함에 따라 ALON의 생성량이 증가하였으며, Al 첨가량 10wt%까지는 $1750^{\circ}C$ 이상의 소결온도에서 ALON상만이 존재하였다. Al 첨가량 13wt% 이상의 조성에서는 약간의 AlN상이 ALON상과 공존하였다. 반응소결체의 밀도는 소결온도가 증가함에 따라 증가하였으나, AlN이 잔존하는 시편의 소결밀도는 $1750^{\circ}C$를 넘으면 약간 감소하였다. Al 첨가량이 증가할수록 입내파괴현상이 현저히 증가하였다.

• The Korean Journal of Ceramics
• /
• 제4권4호
• /
• pp.323-330
• /
• 1998

Mixed oxide compounds of potential usefulness for fibre coatings (hexagonal celsian, $BaAl_2Si_2O_8$ and lanthanum hexaluminate, $LaAl_{11}O_{18}$) or for matrix materials (yttrium aluminium garnet, $Y_3Al_5O_{12}$) were prepared by hybrid sol-gel synthesis and their thermal crystallisation was monitored by thermal analysis, X-ray diffraction and multinuclear solid state MAS NMR. All the gels convert to the crystalline phase below about $12200^{\circ}C$, via amorphous intermediates in which the Al shows and NMR resonance at 36-38 ppm sometimes ascribed to Al in 5-fold coordination. Additional information about the structural changes during thermal treatment was provided by $^{29}Si$, $^{137}Ba$ and $^{89}Y$ MAS NMR spectroscopy, showing that the feldspar framework of celsian begins to be established by about $500^{\circ}C$ but the Ba is still moving into its polyhedral lattice sites about $400^{\circ}C$ after the sluggish onset of crystallization. Lanthanum hexaluminate and YAG crystallise sharply at 1230 and $930^{\circ}C$ respectively, the former via $\gamma-Al_2O_3$, the latter via $YAlO_3$. Yttrium moves into the garnet lattice sites less than $100^{\circ}C$ after crystallisation.

• E2M - 전기 전자와 첨단 소재
• /
• 제16권9호
• /
• pp.63.1-63
• /
• 2003

Catalytic chemical vapor deposition (Cat-CVD) has been developed to deposit alumina(Al$_2$O$_3$) thin films on silicon (Si) crystal using N$_2$ bubbled tir-methyl aluminium [Al(CH$_3$)$_3$, TMA] and molecular oxygen (O$_2$) as source species and tungsten wires as a catalyzer. The catalyzer dissociated TMA at approximately 600$^{\circ}C$ The maximum deposition rate was 18 nm/min at a catalyzer temperature of 1000 and substrate temperature of 800$^{\circ}C$. Metal oxide semiconductor (MOS) diodes were fabricated using gates composed of 32.5-nm-thick alumina film deposited as a substrate temperature of 400oC. The capacitance measurements resulted in a relatively dielectric constant of 7, 4, fixed charge density of 1.74*10e12/$\textrm{cm}^2$, small hysteresis voltage of 0.12V, and very few interface trapping charge. The leakage current was 5.01*10e-7 A/$\textrm{cm}^2$ at a gate bias of 1V.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1281-1282
• /
• 2008

Low cost TCO(Transparent Conductive oxide) thin films were prepared by 3" DC/RF magnetron sputtering systems. For the AZO preparation processes a 99.99% AZO target (Zn: 98 wt.%, $Al_2O_3$: 2 wt.%) was used. In order to verify feasibility of the AZO thin films to organic light emitting device (OLED) application, test organic light emitting device was fabricated based on AZO as TCO, TPD as hole transporting layer (HTL), Alq3 as both emitting layer (EML) and electron transporting layer (ETL), and aluminium as cathode, where the both ITO and AZO surfaces were treated using $O_2$ RF plasma. The I-V characteristics of the AZO/TPD/Alq3/Al OLEDs were evaluated. As the results, the performance of the OLEDs with AZO as transparent conducting anode could be useable.

• 전기학회논문지
• /
• 제56권10호
• /
• pp.1782-1785
• /
• 2007

In this paper, the effect of substrate temperature on structural, electrical and optical properties of aluminium-doped zinc oxide (AZO) films were investigated. AZO thin films were prepared on glass substrate by pulsed DC magnetron sputtering technique. The properties of AZO were measured by using XRD, AFM, UV spectrophotometer, and hall effect measurement system. The resistivity of AZO films was improved under the condition of high substrate temperature. The resistivity decreased from $9.95{\times}10^{-2}\;{\Omega}-cm\;to\;1.1{\times}10^{-3}\;{\Omega}-cm$ as a result of high substrate temperature and the average transmittances in visible range were above 80%.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.167-167
• /
• 2012

Aluminium-zinc-tin oxide (AZTO) 박막 트랜지스터는 Spin-coating 방법으로 제작되었다. AZTO용액의 용매는 2-Methoxyethanol, 용질은 각각 Aluminium nitride, Zinc acetate dihydrate, Tin chloride가 사용되어 제작되었다. 용액의 안정성을 위해서 미량의 Mono ethyl amine이 첨가되었다. 용액의 Zn:Sn의 몰 비율은 1 : 1로 고정 되었으며 Al의 mole비를 다양하게 늘리면서 실험을 진행하였다. 이렇게 만들어진 AZTO용액은 3,000 rpm으로 30초간 Spin-coating하였으며 이후 Furnace system을 통하여 $500^{\circ}C$의 온도로 1시간 동안 후열처리 공정을 진행하였다. AZTO박막을 활성층으로 제작된 박막 트랜지스터는 Al의 비율이 늘어남에 따라 처음엔 이동도가 증가하였으나 이후 이동도가 낮아지며 소자특성이 나빠지는 것을 보였다. 이러한 현상의 원인을 알아보고자 물리적, 전기적, 광학적 분석을 통해서 Al양의 변화가 박막트랜지스터 구동에 미치는 영향을 해석하였다. 먼저 AZTO용액은 열중량측정/시차열분석법(Thermo Gravimetry/Differential Thermal Analysis)을 이용하여 spin-coating 이후 후 열처리 온도 결정 및 박막의 변화를 관찰하였으며, X-선 분광(X-ray photoelectron spectroscopy)을 이용하여 박막의 조성 및 전자구조의 변화를, 타원분광해석법(Spectroscopic Ellipsometry)분석을 통하여 밴드 갭과 전도대 이하 밴드 갭 내에 존재하는 결함상태변화를 관찰하였다. AZTO 박막 내의 Al양을 조절하는 것은 박막내의 에너지 준위의 변화를 야기하고 그로인해 박막트랜지스터의 특성을 변화킨다는 결과를 도출하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권10호
• /
• pp.1200-1205
• /
• 2014

The effect of nanofluids on the heat transfer performance of a pulsating heat pipe has been experimentally investigated. Water-based diamond nanofluid and aluminium oxide ($Al_2O_3$) nanofluid were tested in the concentration range of 0.5-5%. The pulsating heat pipe was constructed using clear Pyrex tubes of 1.85 mm in inner diameter in order to visualize the pulsating action. The total number of turns was eight each for heated and cooled parts. The supply temperatures of heating water and cooling water were fixed at $80^{\circ}C$ and $25^{\circ}C$ respectively. The liquid charging ratio of the nanofluid was 50-70%. The test results showed that the case of 5% concentration of diamond nanofluid showed 18% increase in heat transfer rate compared to pure water. The case of 0.5% concentration of $Al_2O_3$ nanofluid showed 24% increase in heat transfer rate compared to pure water. But the increase of $Al_2O_3$ nanofluid concentration up to 3% did not show further enhancement in heat transfer. It is also observed that the deposited nanoparticles on the tube wall played a major role in enhanced evaporation of working fluid and this could be the reason for the enhancement of heat transfer by a nanofluid, not the enhanced thermal conductivity of the nanofluid.

• 한국재료학회지
• /
• 제31권3호
• /
• pp.150-155
• /
• 2021

Zinc oxide (ZnO) based transparent conducting oxides (TCO) thin films, are used in many applications such as solar cells, flat panel displays, and LEDs due to their wide bandgap nature and excellent electrical properties. In the present work, fluorine and aluminium-doped ZnO targets are prepared and thin films are deposited on soda-lime glass substrate using a RF magnetron sputtering unit. The aluminium concentration is fixed at 2 wt%, and the fluorine concentration is adjusted between 0 to 2.0 wt% with five different concentrations, namely, Al2ZnO98(AZO), F0.5AZO97.5(FAZO1), F1AZO97(FAZO2), F1.5AZO96.5(FAZO3), and F2AZO96(FAZO4). Thin films are deposited with an RF power of 40 W and working pressure of 5 m Torr at 270 ℃. The morphological analysis performed for the thin film reveals that surface roughness decreases in FAZO1 and FAZO2 samples when doped with a small amount of fluorine. Further, optical and electrical properties measured for FAZO1 sample show average optical transmissions of over 89 % in the visible region and 82.5 % in the infrared region, followed by low resistivity and sheet resistance of 3.59 × 10-4 Ωcm and 5.52 Ω/sq, respectively. In future, these thin films with excellent optoelectronic properties can be used for thin-film solar cell and other optoelectronics applications.

• 대한금속재료학회지
• /
• 제48권6호
• /
• pp.523-532
• /
• 2010

Co-application of organic coating and cathodic protection has not provided enough durability to low-alloyed steels inseawater ballast tank (SBT) environments. An attempt has made to study the effect of alloy elements (Al, Cr, Cu, Mo, Ni, Si, W) on general and localized corrosion resistance of steels as basic research to develop new low-allowed steels resistive to corrosion in SBT environments. For this study, we measured the corrosion rate by the weigh loss method after periodic immersion in synthetic seawater at $60^{\circ}C$, evaluated the localized corrosion resistance by an immersion test in concentrated chloride solution with the critical pH depending on the alloy element (Fe, Cr, Al, Ni), determined the permeability of chloride ion across the rust layer by measuring the membrane potential, and finally, we analyzed the rust layer by EPMA mapping and compared the result with the E-pH diagram calculated in the study. The immersion test of up to 55 days in the synthetic seawater showed that chromium, aluminium, and nickel are beneficial but the other elements are detrimental to corrosion resistance. Among the beneficial elements, chromium and aluminium effectively decreased the corrosion rate of the steels during the initial immersion, while nickel effectively decreased the corrosion rate in a longer than 30-day immersion. The low corrosion rate of Cr- or Al-alloyed steel in the initial period was due to the formation of $Cr_2FeO_4$ or $Al_2FeO_4$, respectively -the predicted oxide in the E-pH diagram- which is known as a more protective oxide than $Fe_3O_4$. The increased corrosion rate of Cr-alloyed steels with alonger than 30-day exposure was due to low localized corrosion resistance, which is explained bythe effect of the alloying element on a critical pH. In the meantime, the low corrosion rate of Ni-alloyed steel with a longer than 30-day exposure wasdue to an Ni enriched layer containing $Fe_2NiO_4$, the predicted oxide in the E-pH diagram. Finally, the measurement of the membrane potential depending on the alloying element showed that a lower permeability of chloride ion does not always result in higher corrosion resistance in seawater.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제13권1호
• /
• pp.92-100
• /
• 2008

본 연구는 시멘트 구성성분 중 CaO, $Fe_2O_3$, $Al_2O_3$를 중심으로 하여 시멘트/Fe(II) 시스템에서 TCE의 환원성 탈염소화에 관여하는 유효반응성분을 규명하기 위하여 수행되었다. $Al_2O_3$를 함유하는 것으로 밝혀진 hematite($Fe_2O_3$)를 포함하는 hematite/CaO/Fe(II) 시스템에서 시멘트/Fe(II) 시스템과 유사한 TCE 분해능이 나타나는 것을 확인할 수 있었다. Hematite/CaO/$Al_2O_3$/Fe(II) 시스템에서 $Al_2O_3$의 첨가량의 영향을 알아보는 실험을 수행한 결과 $Al_2O_3$:CaO의 비율이 1:10을 유지한 시스템에서 최고의 분해능(k = 0.895 $day^{-1}$)을 보이는 것으로 보아 1 : 10이 최적의 반응비율인 것을 알 수 있었다. SEM 분석 결과 시멘트/Fe(II) 시스템에서 나타났던 막대결정을 hematite/CaO/$Al_2O_3$/Fe(II) 시스템에서도 관찰할 수 있었다. 이러한 막대결정을 TCE 분해의 유효성분으로 추정하고 막대나 침상 결정으로 알려진 goethite와 ettringite를 유효성분 후보군으로 판단하였다. EDS element map을 살펴본 결과, 막대 결정은 Ca를 주성분으로 하고 있었기 때문에 Fe 성분을 다량 함유하고 있는 goethite를 배제하였다. 추가적으로 시멘트 수화반응 중 ettringite가 생성되는 과정을 재연한 실험 결과, ettringite가 생성되는 반응 중 혹은 생성 후에도 TCE 분해능이 발현되지 않았다. 이러한 결과를 바탕으로 하여 시멘트/Fe(II) 시스템의 유효반응성분은 CaO와 $Al_2O_3$를 주성분으로 하는 막대모양의 결정일 것으로 판단된다.