• Korean Journal of Materials Research
• /
• v.5 no.4
• /
• pp.420-425
• /
• 1995

AlGaN/GaInN 이중이종접합구조(double heterostructure :DH)를 대기압 유기금속기상에 피텍셜(MOVPE)법으로 AIN 와충층을 이용하여 사파이어 기판위에 성장하고, 실온에서의 광여기법에 의한 청색영역의 단면모드 유도방출특성과 편광특성을 조사하였다. 여기광원의 광밀도가 증가함에 따라 청색 영역에서의 유도방출 피크는 낮은 에너지 쪽으로 이동하였고, 유도방출 피크파장은 여기광밀도가 200kW/$cm^{2}$일때 402nm 이었으며, 스펙트럼의 반치폭은 18meV 이었다. 또한 유도방출에 필요한 여기광밀도의 임계치는 130 kW/$cm^{2}$ 이었다. AlGaN/GaInN로부터 방출되는 유도방출 광은 임계치 이상에서 TE-mode로 편광 되었다.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.28A no.1
• /
• pp.30-39
• /
• 1991

The influence of physical parameters (Al mole fraction, thickness, doping concentration) in the window and emitter on the efficiency characteristics of heteroface p-$Al_{x}Ga_{1-x}As/p-GaAs/n-GaAs/n^{+}$-GaAs solar cell is investigated. The maximum efficiency theoretically calculated in this device is obtained when a thickness of the window is in a range of (400-1000))$\AA$and a thickness/doping concentration of the emitter is in a range of (0.5-0.8)$\mu$m/(1-7)${\times}10^{17}cm^{-3}$, respectively. Also is the efficiency improved according to the increase of Al mole fraction in the indirect gap window(0.41${\le}x{\le}1.0$). The optimum designed heteroface cell with an area of 0.165cm$^2$fabricated using MOCVD exhibits an active area conversion efficiency of 17%, having a short circuit current density of 21.2mA/cm\ulcorner an open circuit voltage of 0.94V, and a fill factor of 0.75 under ELH-100mW/cm$^2$illumination.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.2
• /
• pp.49-53
• /
• 2010

Microstructural origins of leakage current and physical degradation during operation in product-quality AlGaN/GaN high electron mobility transistor (HEMT) devices were investigated using photon emission microscopy (PEM) and transmission electron microscopy (TEM). AlGaN/GaN HEMTs were fabricated with metal organic chemical vapor deposition on semi-insulating SiC substrates. Photon emission irregularity, which is indicative of gate leakage current, was measured by PEM. Site specific TEM analysis assisted by a focused ion beam revealed the presence of threading dislocations in the channel below the gate at the position showing strong photon emissions. Observation of electrically degraded devices after life tests revealed crack/pit shaped defects next to the drain in the top AlGaN layer. The morphology of the defects was three-dimensionally investigated via electron tomography.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.1
• /
• pp.18-22
• /
• 2005

We have proposed and fabricated a dual gate AlGaN/GaN high electron mobility transistor (HEMT), which exhibits the low leakage current and the high breakdown voltage for the high voltage switching applications. The additional gate between the main gate and the drain is specially designed in order to decrease the electric field concentration at the drain-side of the main gate. The leakage current of the proposed HEMT is decreased considerably and the breakdown voltage increases without sacrificing any other electric characteristics such as the transconductance and the drain current. The experimental results show that the breakdown voltage and the leakage current of proposed HEMT are 362 V and 75 nA while those of the conventional HEMT are 196 V and 428 nA, respectively.

• Journal of the Korean Vacuum Society
• /
• v.17 no.4
• /
• pp.353-358
• /
• 2008

In order to increase extraction efficiency of AlGaInP-based vertical RED LEDs, chemical wet etching technique was produced by using a roughened surface with triangle-like morphology. A commonly used $H_3PO_4$-based solution was applied for chemical wet etching. The light extraction of AlGaInP LED was related to the n-side roughed surface morphology. The morphology of roughed surface is analyzed by the atomic force microscope (AFM). As a result, the roughed surface AlGaInP LED has a root-mean-square (RMS) roughness of 44 nm. The brightness shows 41% increase after roughening n-side surface, as compared to the ordinary flat surface LED.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.4
• /
• pp.266-270
• /
• 2011

We report on the formation mechanism of large Schottky barrier height (SBH) of nonalloyed Cr Schottky contacts on strained Al0.25Ga0.75N/GaN. Based on the current-voltage (I-V) and capacitance-voltage (C-V) data, the SBHs are determined to be 1.98 (${\pm}0.02$) and 2.07 (${\pm}0.02$) eV from the thermionic field emission and two-dimensional electron gas (2DEG) calculations, respectively. Possible formation mechanism of large SBH will be described in terms of the formation of Cr-O chemical bonding at the interface between Cr and AlGaN/GaN, low binding-energy shift to surface Fermi level, and the reduction of 2DEG electrons.

• Korean Journal of Materials Research
• /
• v.24 no.12
• /
• pp.645-651
• /
• 2014

GaN is most commonly used to make LED elements. But, due to differences of the thermal expansion coefficient and lattice mismatch with sapphire, dislocations have occurred at about $109{\sim}1010/cm^2$. Generally, a low temperature GaN buffer layer is used between the GaN layer and the sapphire substrate in order to reduce the dislocation density and improve the characteristics of the thin film, and thus to increase the efficiency of the LED. Further, patterned sapphire substrate (PSS) are applied to improve the light extraction efficiency. In this experiment, using an AlN buffer layer on PSS in place of the GaN buffer layer that is used mainly to improve the properties of the GaN film, light extraction efficiency and overall properties of the thin film are improved at the same time. The AlN buffer layer was deposited by using a sputter and the AlN buffer layer thickness was determined to be 25 nm through XRD analysis after growing the GaN film at $1070^{\circ}C$ on the AlN buffer CPSS (C-plane Patterned Sapphire Substrate, AlN buffer 25 nm, 100 nm, 200 nm, 300 nm). The GaN film layer formed by applying a 2 step epitaxial lateral overgrowth (ELOG) process, and by changing temperatures ($1020{\sim}1070^{\circ}C$) and pressures (85~300 Torr). To confirm the surface morphology, we used SEM, AFM, and optical microscopy. To analyze the properties (dislocation density and crystallinity) of a thin film, we used HR-XRD and Cathodoluminescence.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.292-292
• /
• 2014

Wide band gap semiconductors, such as III-nitrides (GaN, AlN, InN, and their alloys), SiC, and diamond are expected to play an important role in the next-generation electronic devices. Specifically, GaN-based high electron mobility transistors (HEMTs) have been targeted for high power, high frequency, and high temperature operation electronic devices for mobile communication systems, radars, and power electronics because of their high critical breakdown fields, high saturation velocities, and high thermal conductivities. For the stable operation, high power, high frequency and high breakdown voltage and high current density, the fabrication methods have to be optimized with considerable attention. In this study, low ohmic contact resistance and smooth surface morphology to AlGaN/GaN on 2 inch c-plane sapphire substrate has been obtained with stepwise annealing at three different temperatures. The metallization was performed under deposition of a composite metal layer of Ti/Al/Ni/Au with thickness. After multi-layer metal stacking, rapid thermal annealing (RTA) process was applied with stepwise annealing temperature program profile. As results, we obtained a minimum specific contact resistance of $1.6{\times}10^{-7}{\Omega}cm2$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.8
• /
• pp.654-658
• /
• 2009

For investigation of surface leakage currrent of AlGaN/GaN heterostructures through etched GaN buffer surface and mesa wall, three kind of surface-leakage-test-patterns were fabricated. and we measured the surface leakage current of each patterns. In result of our work, the surface leakage current of pattern of which Schottky contact is formed on etched mesa wall is the largest. the leakage current through schottky contact on etched mesa wall is predominant in AlGaN/GaN heterostructures.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.10
• /
• pp.1202-1208
• /
• 1988

The electron density and electronic states in n- AlGaAs/GaAs heterointerface are calculated by using classical- and quantum-mechanics, respectively. We examine the effects of spacer layer thickness and doping concentration in AlGaAs layer on 2DEG density. Also, the dependences of electronic states of 2DEG upon temperature and acceptor concentration in GaAs layer are investigated.