• 마이크로전자및패키징학회지
• /
• 제13권3호
• /
• pp.33-38
• /
• 2006

유리 조성이 섞인 유전체 파우더와 증류수 그리고 해교제의 혼합으로 만들어진 슬러리를 에어로졸 형태로 고압 스프레이 건으로 기판에 스프레이 코팅 하였다. 기판으로는 알루미나 기판과 전극 패턴이 프린트 된 그린쉬트를 사용하였다. 슬러리 점도와 스프레이 건에 의한 분사모양 그리고 슬러리의 분사량은 코팅 층의 코팅 속도에 영향을 끼쳤으나 밀도에는 거의 영향을 주지 않았다. 고압 스프레이 코팅 방법은 기판에 직접적인 가압 과정이 없으므로 내부 전극은 인쇄된 형태가 유지되었다. 최적 조건에서는 균일하고 조밀한 코팅 층을 얻을 수 있었다. 또한 그린쉬트에 적층 공정을 사용한 기존의 방법과는 달리 고압 스프레이 코팅 방법은 $20{\sim}50{\mu}m$의 얇은 유전체 층을 얻을 수 있었다.

• 한국표면공학회지
• /
• 제46권5호
• /
• pp.208-215
• /
• 2013

The aim of the present study was to improve the radiative heat dissipation of aluminum alloy, Al 1050. Resin/CuO coating and Cu/CuO composite plating were applied on aluminum alloy to improve the radiative heat dissipation. Resin/CuO coating was made using thermosetting silicon resin and Cu/CuO composite plating was made in pyrophosphate copper plating bath. Radiant heat flux($W/m^2$) was measured by self-produced radiant heat measurement device to compare each specimen. The cross section of specimen and chemical bonding of surface were analyzed by FE-SEM, XPS and FT-IR. As a result, radiant heat of Resin/CuO coating was higher than Cu/CuO composite plating due to the adhesion with aluminum plate and the difference in chemical bonding. But, Both of them were higher than aluminum alloy. In order to confirm the result of experiment, aluminum plate, Resin/CuO coating and Cu/CuO composite plating sample were applied LED and measured the LED temperature. As a result, LED temperature of samples were matched previous results and confirmed coated samples were lower about 10 degrees than the aluminum alloy.

• 한국환경보건학회지
• /
• 제42권1호
• /
• pp.27-33
• /
• 2016

Objectives: Alumina nanoparticles ($Al_2O_3$, Al-NPs) are used for various purposes, including as coating agents and paint additives. Their potential toxicity has raised concern for human health. This study focuses on exploring the toxic effects on the brain and kidneys caused by Al-NPs exposure in rats. Methods: The animals were orally administered Al-NPs at 10, 50 and 100 mg/kg body weight for 28 days following OECD TG 407. To determine the targeted toxicity of Al-NPs, histopathological examination and gene expression analysis were conducted on the rats. Results: The Al-NPs treatment induced kidney tubular dilatation. In the rat cerebrums, the expression levels of 126 genes experienced two-fold or greater increases in response to Al-NPs, including other genes encoding proteins involved in cell differentiation, transcription and signal transduction. In the rat kidneys, the expression levels of 152 genes also showed two-fold or greater increases in response to Al-NPs, including other genes encoding proteins involved in apoptosis, transcription and signal transduction. Conclusion: These results suggest that exposure to Al-NPs influences cellular signal pathways of kidney and cerebrum, and it can be a toxic indicators of nanometrials.

• 한국표면공학회지
• /
• 제49권3호
• /
• pp.307-315
• /
• 2016

The properties of AlTiN films by a cathodic arc deposition process have been studied. Oblique angle deposition has been applied to deposit AlTiN films. AlTiN films have been deposited on stainless steel (SUS304) and cemented carbide (WC) at a substrate temperature of $500^{\circ}C$. AlTiN films were analyzed by scanning electron microscopy, glow-discharge light spectroscopy, micro-vickers hardness, and nanoindenter. When applying a current of 50 A to the cathodic arc source, it showed that the density of macroparticle of AlTiN films was 5 lower than other deposition conditions. With the increase of the bias voltage applied to the substrate up to -150 V, the density of macroparticle was decreased. The change of the $N_2$ flow rate during coating process made no influence on the film properties. For the multi-layered films, the film prepared at oblique angle of $60^{\circ}$ showed the highest hardness of 28 GPa and $H^3/E^2$ index of 0.18. AlTiN films have been shown a good oxidation resistance up to $800^{\circ}C$.

• 한국표면공학회지
• /
• 제42권6호
• /
• pp.272-275
• /
• 2009

The purpose of this study is to show the friction and wear characteristic behaviors of TiN and CrN coated SKD61 which is applied to Al 6xxx extrusion mold material. The friction and wear characteristic behaviors of both coating layers were investigated by the reciprocating friction wear tester under atmospheric pressure and un-lubricated state. The processing parameters in this study were temperature (50 and $120^{\circ}C$) and load (3, 5, and 11 kgf). This study was carried out while comparing the coefficient of friction and microstructure of TiN and CrN coating layers on SKD61. The coefficient of friction of CrN became lower than that of TiN at all conditions. Therefore, CrN was suggested to be more advantageous than TiN for extrusion mold.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2016년도 추계학술대회 논문집
• /
• pp.173.2-173.2
• /
• 2016

A two-step oxidation method was applied on Al6061 to debate the growth mechanism of plasma electrolytic oxidation (PEO) coating. The specimens were first oxidized in the primary electrolyte solution {$Na_3PO_4$ (8g/l), NaOH (2g/l), consequently, the specimens were transferred into a different electrolyte {$K_2ZrF_6$ (8g/l), NaOH (2g/l), $Na_2SiF_6$ (0.5g/l)} for further oxidation. The processes was conducted for various processing times. It was found the second step electrolyte component were reached to inner layers, in contrast to the primary step components which were thrustle to the outer layer. The presence of the secondary component in the inner layers were significantly varied with processing time which suggest the change in growth properties with processing time. further more the inside growth of the secondary component confirmed the increasing trend in the downward growth of the coating layer. The corrosion and hardness properties of the coatings were found highly improved with change in growth features with increasing the processing time.

• 한국해양공학회지
• /
• 제23권6호
• /
• pp.99-104
• /
• 2009

PTFE has good mechanical and chemical stability at a wide range of temperatures and demonstrates a low friction coefficient value. PTFE is being used for self-lubricating parts in industry. But it shows a high wear rate. Thus, PTFE and nano-diamond powder were mixed into a composite and the wear properties of a PTFE coating layer on Al6061 was investigated. A ball-on-disk type of wear tester was used under a dry condition and different temperatures of oil. After the wear test, the wear track wasexamined by optical microscope. The PTFE-diamond showed the lowest friction coefficient (0.02) of all the lubricants in the experiments. The friction coefficient was shown to be directly related to the diamond powder in the PTFE coating. Adhesion estimations were performed by a scratch test, which is mainly used for coatings. The critical load between the coating and substrate was defined through analyses of the friction load, normal load curve, and acoustic emissions, along with optical microscope observations. The scratch test results showed that an import item (SWISS) gave the highest critical load values.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.251-254
• /
• 2001

This paper describes an efficiency improvement of buried contact solar cell (BSCS) with a structure of MgF$_2$/CeO$_2$/Ag/Cu/Ni grid/n$^{+}$ emitter/p-type Si base/p$^{+}$/Al. Theoretical and experimental investigations were performed on a double layer antireflection (DLAR) coating of MgF$_2$/CeO$_2$. We investigated CeO$_2$ films as an AR layer because they have a proper refractive index of 2.46 and demonstrate the same lattice constant as Si substrate. An optimized DLAR coating shewed a reflectance as low as 2.04 % in the wavelengths ranged from 0.4 ${\mu}{\textrm}{m}$ to 1.1 ${\mu}{\textrm}{m}$. BCSC cell efficiency was improved from 16.2 % without any AR coating to 19.9 % by employing DLAR coatings. Further details on MgF$_2$/CeO$_2$ DLAR coatings on the BCSC cells are presented in this paper.per.

• Journal of Electrochemical Science and Technology
• /
• 제7권2호
• /
• pp.179-184
• /
• 2016

The interface between the surface of a cathode material and the electrolyte gives rise to surface reactions such as solid electrolyte interface (SEI) and chemical side reactions. These reactions lead to increased surface resistance and charge transfer resistance. It is consequently necessary to improve the electrochemical characteristics by suppressing these reactions. In order to suppress unnecessary surface reactions, we coated cathode material using polypropylene (PP). The PP coating layer effectively reduced the SEI film that is generated after a 4.3 V initial charging process. By mitigating the formation of the SEI film, the PP-coated Li[(Ni_0.6Co_0.1Mn_0.3)_0.36(Ni_0.80Co_0.15Al0.05)_0.64)]O₂(NCS) electrode provided enhanced transport of Li⁺ ions due to reduced SEI resistance (R_SEI) and charge transfer resistance (R_ct). The initial charge and discharge efficiency of the PP-coated NCS electrode was 96.2 % at a current density of 17 mA/g in a voltage range of 3.0 ~ 4.3 V, whereas the efficiency of the NCS electrode was only 94.7 %. The presence of the protective PP layer on the cathode improved the thermal stability by reducing the generated heat, and this was confirmed via DSC analysis by an increased exothermic peak.

• 한국분말재료학회지
• /
• 제24권2호
• /
• pp.102-107
• /
• 2017

Porous polytetrafluoroethylene (PTFE) thin films are fabricated by spin-coating using a dispersion solution containing PTFE powders, and their crystalline properties are investigated after thermal annealing at various temperatures ranging from 300 to $500^{\circ}C$. Before thermal annealing, the film is densely packed and consists of many granular particles 200-300 nm in diameter. However, after thermal annealing, the film contains many voids and fibrous grains on the surface. In addition, the film thickness decreases after thermal annealing owing to evaporation of the surfactant, binder, and solvent composing the PTFE dispersion solution. The film thickness is systematically controlled from 2 to $6.5{\mu}m$ by decreasing the spin speed from 1,500 to 500 rpm. A triboelectric nanogenerator is fabricated by spin-coating PTFE thin films onto polished Cu foils, where they act as an active layer to convert mechanical energy to electrical energy. A triboelectric nanogenerator consisting of a PTFE layer and Al metal foil pair shows typical output characteristics, exhibiting positive and negative peaks during applied strain and relief cycles due to charging and discharging of electrical charge carriers. Further, the voltage and current outputs increase with increasing strain cycle owing to accumulation of electrical charge carriers during charge-discharge.