• 한국주조공학회지
• /
• 제23권2호
• /
• pp.77-85
• /
• 2003

Some alloying elements such as Cr, B, Ti and Si were added individually or as a mixture to Fe-30 at.%Al alloys. The alloys were melted using an arc furnace and then heat-treated for homogenization at 1000$^{\circ}C$ for 7 days and followed by rolling at 1000$^{\circ}C$. The alloying elements on rolling characteristics were investigated by the microstructures and fracture mode before and after rolling. The microstructures before rolling showed that all of the alloys had equiaxed grains. On the other hand, the microstructures of rolling plane as well as its perpendicular plane became elongated after rolling. The alloys such as Fe-30Al, Fe-30Al-3Ti, Fe-30Al-0.5B, Fe-30Al-5Cr and Fe-30Al-3Ti-0.5B revealed better rolling behaviour from the point that intergranular and cleavage fractures were not fundamentally occurred. But the addition of 5Ti or 3Si to Fe-Al alloys had detrimental effects. The Ti-added alloy system such as Fe-30Al-5Ti, Fe-30Al-5Ti-5Cr, Fe-30Al-3Ti-5Cr and Fe-30Al-5Ti-0.5B were cracked through grain and showed cleavage fracture. The Si-added alloy system such as Fe-30Al-5Si, Fe-27Al-3Si and Fe-27Al-5Cr-3Si were cracked along the grain boundary and showed intergranular fracture. $DO_3{\leftrightarrow}B_2$ transition temperature of Fe-30at.%Al alloy was 520$^{\circ}C$, whereas the addition of 3Ti and 3Ti+0.5B comparably increased the temperature to 797 and 773$^{\circ}C$, respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.108-110
• /
• 2000

The aim of this paper is to investigate the effect of Al and Ti on microstructure of Fe-Cr-Al alloy systems for applying electrical resistance wires of electrical furnace. From the preliminary study, the amount of recovered addition elements increased in the case of both vacuum and Ar-atmosphere melting than that in the case of air-atmosphere melting. Also, optimum Cr content for good performance at high temperature was approximately 24wt% from the observation of microstucture. The precipitates of Fe-Cr, Al-Cr and Al phases were observed, adding Al and Ti. Especially, Sharp rectangular shapes of precipitates were observed with increasing amount of Ti.

• 한국표면공학회지
• /
• 제34권1호
• /
• pp.39-48
• /
• 2001

Fe-Cr-Al alloy has been studied for application in automobile muffler materials due to good corrosion and oxidation resistance. In order to develop the automobile muffler materials, corrosion behaviors of electron beam physical vapor deposition (EB-PVD) coated surface of muffler matericls of muffler materials were investigated using potentiostat. For 0.1M NaCl solution, corrosion potential and pitting potential of Fe-20Cr-10Al was higher than that of Fe-5Cr- 10Al samples. Especially, in the case of Ti and Nb coated samples, pitting potential increased remarkably compared with non-coated samples. For 0.1M $CaCl_2$ solution, Ti-coated Fe-20Cr-10Al showed remarkably improved pitting corrosion resistance in comparison with non-coated Fe-20Cr-10Al and Fe-5Cr-10Al. The number and size of pits were decreased in the case of Ti coated samples in the 0.1M NaCl and 0.1M $CaCl_2$ solution.

• Metals and materials international
• /
• 제24권6호
• /
• pp.1213-1220
• /
• 2018

The effects of Cr and Fe addition on the mechanical properties of Ti-6Al-4V alloys prepared by direct energy deposition were investigated. As the Cr and Fe concentrations were increased from 0 to 2 mass%, the tensile strength increased because of the fine-grained equiaxed prior ${\beta}$ phase and martensite. An excellent combination of strength and ductility was obtained in these alloys. When the Cr and Fe concentrations were increased to 4 mass%, extremely fine-grained martensitic structures with poor ductility were obtained. In addition, Fe-added Ti-6Al-4V resulted in a partially melted Ti-6Al-4V powder because of the large difference between the melting temperatures of the Fe eutectic phase (Ti-33Fe) and the Ti-6Al-4V powder, which induced the formation of a thick liquid layer surrounding Ti-6Al-4V. The ductility of Fe-added Ti-6Al-4V was thus poorer than that of Cr-added Ti-6Al-4V.

• 한국표면공학회지
• /
• 제36권6호
• /
• pp.480-490
• /
• 2003

Effects of plasma-nitriding on the pitting corrosion of Fe-30at%Al-5at%Cr alloy containing Ti, Hf, and Zr were investigated using potentiostat in 0.1M HCl. The specimen was casted by the vacuum arc melting. The subsequent homogenization was carried out in Ar gas atmosphere at $1000^{\circ}C$ for 7days and phase stabilizing heat treatment was carried out in Ar gas atmosphere at $500^{\circ}C$ for 5 days. The specimen was nitrided in the $N_2$, and $H_2$, (1:1) mixed gas of $10^{-4}$ torr at $480^{\circ}C$ for 10 hrs. After the corrosion tests, the surface of the tested specimens were observed by the optical microscopy and scanning electron microscopy(SEM). For Fe-30at%Al-5Cr alloy, the addition of Hf has equi-axied structure and addition of Zr showed dendritic structure. For Fe-30at%Al-5Cr alloy containing Ti, plasma nitriding proved beneficial to decrease the pitting corrosion attack by increasing pitting potential due to formation of TiN film. Addition of Hf and Zr resulted in a higher activation current density and also a lower pitting potential. These results indicated the role of dendritic structure in decreasing the pitting corrosion resistance of Fe-30Al-5Cr alloy. Ti addition to Fe-30Al-5Cr decreased the number and size of pits. In the case of Zr and Hf addition, the pits nucleated remarkably at dendritic branches.

• 한국주조공학회지
• /
• 제21권1호
• /
• pp.24-32
• /
• 2001

Recently, iron aluminides based on Fe3Al and FeAl are ordered intermetallic alloys that offer good oxidation resistance, excellent sulfidation resistance, and potentially lower cost than many high-temperature structural materials. They have better strength, elasticity to weight ratio and high temperature strength, therefore, they can be cosidered as candidate heat resistance structural materials for automobiles, ships, airplanes and spaceships applications. The changes in the mechanical properties and fracture behavior were investigated for Fe-30at.%Al-5at.%Cr alloys when Ti, Hf and Zr were added respectively. For mechanical properties such as Rockwell hardness and yield strength at room temperature, those were decreased in the case of Fe-30at.%Al-5at.%Cr alloy then increased in the case of 5at.% and 10at.% addition of Ti alone. However, Rockwell hardness and yield strength decreased again at 15%Ti then increased dramatically due to the precipitation hardening of the second phase on the specimen at 20%Ti. For fracture modes, cleavage fracture showed in the case of Fe-30at.%Al and Fe-30at.%Al-5at.%Cr alloys. As the amount of Ti addition changed cleavage to transgranular fracture and to quasi-cleavage fracture at 20%Ti. When Hf, Zr and Hf+Zr were added respectively, transgranular, cleavage and quasi-cleavage fracture were coexisted.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.528-530
• /
• 2008

The effect of consolidation temperature on the microstructure, density and mechanical properties (especially, wear property) of $Al_{92.5}-Fe_{2.5}-Cr_{2.5}-Ti_{2.5}$ alloy fabricated by gas atomization and magnetic pulsed compaction was investigated. All consolidated alloys consisted of homogeneously distributed fine-grained fcc-Al matrix and intermetallic compounds. Relative higher mechanical properties in the MPCed specimen were attributed to the retention of the nanostructure in consolidated bulk without cracks. The as consolidated bulk by magnetic pulsed compaction showed the enhanced wear properties than that of a general consolidation process. In addition, the wear mechanism and fracture mode of MPCed bulk was discussed.

• 광물과 암석
• /
• 제33권3호
• /
• pp.195-214
• /
• 2020

삼광 금-은 광상은 과거 한국에서 가장 큰 금-은 광상들 중의 하나였다. 이 광상은 선캠브리아기의 변성퇴적암류내에 발달된 열극대를 충진한 8개조의 석영맥으로 구성된 조산형 금-은 광상이다. 이 광상에서 함 티타늄 광물로는 설석, 티탄철석 및 금홍석이며 설석과 티탄철석은 모암에서만 산출되나 금홍석은 모암과 엽리상 석영맥에서 산출된다. 이들 광물들은 모암에선 흑운모, 백운모, 녹니석, 백색운모, 모나자이트, 저어콘 및 인회석과 엽리상 석영맥에선 백색운모, 녹니석 및 유비철석 등과 함께 산출된다. 설석은 최대 3.94 wt.% (Al₂O₃), 0.49 wt.% (FeO), 0.52 wt.% (Nb₂O₅), 0.46 wt.% (Y₂O₃) 및 0.43 wt.% (V₂O₅) 값을 갖는다. 이 설석은 0.06~0.14 (Fe/Al 비) 값으로 변성기원의 설석이고 X_Al (=Al/Al+Fe³⁺+Ti) 값이 0.06~0.15 값으로 저 함량 알루미늄 설석에 해당된다. 티탄철석은 최대 0.07 wt.% (ZrO₂), 0.12 wt.% (HfO₂), 0.26 wt.% (Nb₂O₅), 0.04 wt.% (Sb₂O₅), 0.13 wt.% (Ta₂O₅), 2.62 wt.% (As₂O₅), 0.29 wt.% (V₂O₅), 0.12 wt.% (Al₂O₃), 1.59 wt.% (ZnO)로써 As₂O₅ 함량이 높게 산출된다. 금홍석의 화학조성은 모암과 엽리상 석영맥에서 각각 최대 0.35 wt.%, 0.65 wt.% (HfO₂), 2.52 wt.%, 0.19 wt.% (WO₃), 1.28 wt.%, 1.71 wt.% (Nb₂O₃), 0.03 wt.%, 0.07 wt.% (Sb₂O₃), 0.28 wt.%, 0.21 wt.% (As₂O₅), 0.68 wt.%, 0.70 wt.% (V₂O₃), 0.48 wt.%, 0.59 wt.% (Cr₂O₃), 0.70 wt.%, 1.90 wt.% (Al₂O₃), 4.76 wt.%, 3.17 wt.% (FeO)로써 엽리상 석영맥의 금홍석에서 HfO₂, Nb₂O₃, As₂O₅, Cr₂O₃, Al₂O₃ 및 FeO 원소들의 함량이 모암의 금홍석보다 높지만 WO₃ 원소의 함량은 낮다. 이 미량원소들은 모암의 금홍석[(Fe³⁺, Al³⁺, Cr³⁺) + Hf⁴⁺+(W⁵⁺, As⁵⁺, Nb⁵⁺) ⟵⟶; 2Ti⁴⁺+ V⁴⁺, 2Fe²⁺+(Al³⁺, Cr³⁺) + Hf⁴⁺+(W⁵⁺, As⁵⁺, Nb⁵⁺) ⟵⟶ 2Ti⁴⁺+2V⁴⁺], 엽리상 석영맥의 금홍석 [(Fe³⁺, Al³⁺) + As⁵⁺ ⟵⟶ Ti⁴⁺+ V⁴⁺, (Fe³⁺, Al³⁺) + As⁵⁺ ⟵⟶ Ti⁴⁺+Hf⁴⁺, 4(Fe³⁺, Al³⁺) ⟵⟶ Ti⁴⁺+(W⁵⁺, Nb⁵⁺) + Cr³⁺]로써 치환관계가 있었다. 이들 자료를 근거로, 모암내 산출되는 설석, 티탄철석 및 금홍석은 광역변성작용 동안 모암광물들의 변질 시 광물내 존재했던 W⁵⁺, Nb⁵⁺, As⁵⁺, Hf⁴⁺, V⁴⁺, Cr³⁺, Al³⁺, Fe³⁺, Fe²⁺ 등과 같은 양이온들의 재 용해 및 농집에 의해 형성되었다. 그후 계속된 연성전단 시 엽리상 석영맥내 금홍석은 열수 용액의 유입에 따른 백색운모와 녹니석의 모암변질작용에 의한 양이온들의 재 용해 및 재 농집과 더불어 초기에 형성된 설석, 티탄철석 및 금홍석과의 반응에 의해 기존에 이들 광물내에 존재하였던 Nb⁵⁺, As⁵⁺, Hf⁴⁺, Cr³⁺, Al³⁺, Fe³⁺, Fe²⁺과 같은 양이온들의 재농집에 의해 형성된 것으로 생각된다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2015년도 춘계학술대회 논문집
• /
• pp.125-125
• /
• 2015

Ti-Al-Cr-N thin layer was prepared on Fe-Si thin sheet by arc ion plating to improve corrosion and mechanical properties. The compositions ratios of Fe : Cr : Al : Ti : Si : N of the thin layers at $500^{\circ}C$ was 1.24 : 0.56 : 36.82 : 32.72 : 0.59 : 28.07 [wt.%], respectively. The higher arc ion plating temperature was, the higher corrosion resistance and nano-hardness were observed due to chromium content. Corrosion potential and corrosion rate in artificial sea water of the coating layer were in the range of $-39mV_{SHE}$ and $2mA/cm^2$, respectively. Passivity was not observed in the artificial sea water. Nano-hardnesses of the thin layers was increased by adding Cr from 23.6 to 25.8 [GPa]. The friction coefficients and fatigue limits of the layers were 0.388, 0.031, respectively.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.708-709
• /
• 2006

New Al-based alloys with very high ultimate tensile strength were developed in high Al concentration range of 91-95 at.% for Al-Fe-Cr-Ti-M (M: Co and Mo) systems and Al-Fe-Cr-Mo-Ti-Co system by the dispersion of nanoscale quasicrystalline particles in Al phase. The effect of adding elements, M was discussed in the viewpoint of stability of super-cooled liquid state and formation ability of quasicrystalline phase. The P/M Al-Fe-Cr-Ti-M alloys with dispersed nanoscale quasicrystalline particles exhibited ultimate tensile strength of 350MPa at 573K and 200MPa at 673K.