• Journal of Electrochemical Science and Technology
• /
• 제12권2호
• /
• pp.237-245
• /
• 2021

Atomic layer deposition (ALD) enhances the stability of cathode materials via surface modification. Previous studies have demonstrated that an Ni-rich cathode, such as LiNi_0.8Co_0.1Mn_0.1O₂, is a promising candidate owing to its high capacity, but is limited by poor cycle stability. In this study, to enhance the stability of the Ni-rich cathode, synthesized LiNi_0.8Co_0.1Mn_0.1O₂ was coated with Al₂O₃ using ALD. Thus, the surface-modified cathode exhibited enhanced stability by protecting the interface from Ni-O formation during the cycling process. The coated LiNi_0.8Co_0.1Mn_0.1O₂ exhibited a capacity of 176 mAh g^-1 at 1 C and retained up to 72% of the initial capacity after 100 cycles within a range of 2.8-4.3 V (vs Li/Li⁺. In contrast, pristine LiNi_0.8Co_0.1Mn_0.1O₂ presented only 58% of capacity retention after 100 cycles with an initial capacity of 173 mAh g^-1. Improved cyclability may be a result of the ALD coating, which physically protects the electrode by modifying the interface, and prevents degradation by resisting side reactions that result in capacity decay. The electrochemical impedance spectra and structural and morphological analysis performed using electron microscopy and X-ray techniques establish the surface enhancement resulting from the aforementioned strategy.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2003년도 추계학술발표강연 및 논문개요집
• /
• pp.226-226
• /
• 2003

The Commercial LiCoO$_2$ particles, which were 7.7${\mu}{\textrm}{m}$ in average diameter, were coated with $Al_2$O$_3$ by a gas suspension spray coating method. The coating amount of $Al_2$O$_3$ on the surface of LiCoO$_2$ was varied from 0.1 to 2 wt.% and compared their electrochemical characteristics with those of bare LiCoO$_2$. $Al_2$O$_3$ coating on the surface of LiCoO$_2$ increased surface area and electrical conductivity, and showed the better cycle and thermal stability even at the higher voltage. The observed optimum A1$_2$O$_3$ coating amount that exhibited the highest capacity retention was 0.2 wt.%.

• 한국전기화학회:학술대회논문집
• /
• 한국전기화학회 2004년도 수소연료전지공동심포지움 2004논문집
• /
• pp.293-296
• /
• 2004

고용량 $LiNi_{1-y}M_yO_2$(M=Al, Zn and Ti, y=0.000, 0.005, 0.010, 0.025, 0.050 and 0.100) 양극재료를 합성하기 위하여 연소법을 사용하였다. 합성한 시료들을 X-선회절 분석, 미세구조관찰, 전자침미세분석(EPMA)을 하였다. battery 충${\cdot}$방전기를 사용하여 리튬의 삽입${\cdot}$추출 반응으로 인하여 나타나는 충${\cdot}$방전 곡선의 변화를 조사하였고, 합성한 각 시편에 대해 충${\cdot}$방전 싸이클 수에 따른 방전용량의 변화를 조사하였다. XRD pattern 분석결과 모든 조성에서 $R\bar{3}m$ 구조를 보여주었다. Ni 자리에 Al, Zn, Ti를 치환한 결과 방전용량은 감소하였으나 M=Al 시료는 싸이클 특성이 증가하였다.

• Transactions on Electrical and Electronic Materials
• /
• 제8권6호
• /
• pp.260-264
• /
• 2007

We have studied stability in organic light-emitting diode depending on buffer layer and cathode. A transparent electrode of indium-tin-oxide(ITO) was used as an anode. An electron injection energy barrier into organic material is different depending on a work function of cathodes. Theoretically, the energy barriers for the electron injection are 1.2 eV, -0.1 eV, and 0.0 eV for Al, LiAl, and LiF/Al at 300 K, respectively. We considered the cases that holes are injected to organic light-emitting diode. The hole injection energy barrier is about 0.7 eV between ITO and TPD without buffer layer. For hole-injection buffer layers of CuPc and PEDOT:PSS, the hole injection energy barriers are 0.4 eV and 0.5 eV, respectively. When the buffer layer of CuPc and PEDOT:PSS is existed, we observed the effects of hole injection energy barrier, and a reduction of operating-voltage. However, in case of PVK buffer layer, the hole injection energy barrier becomes high(1.0 eV). Even though the operating voltage becomes high, the efficiency is improved. A device structure for optimal lifetime condition is ITO/PEDOT:PSS/TPD/$Alq_3$/LiAl at an initial luminance of $300cd/m^2$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.57-58
• /
• 2008

We have studied an organic layer and semitransparent Al electrode thickness dependent optical properties and microcavity effects for top-emission organic light-emitting diodes. Manufactured top-emission device structure is Al(100nm)/TPD(xnm)/Alq(ynm)/LiF(0.5nm)/Al(25nm). While a thickness of total organic layer was varied from 85nm to 165n, a ratio of those two layers was kept to be about 2:3. Semitransparent Al cathode was varied from 20nm to 30nm for the device with an organic layer total thickness of 140nm. As the thickness of total organic layer increases, the emission spectra show a shift of peak wavelength from 490nm to 580nm, and the full width at half maxima from 90nm to 35nm. The emission spectra show a blue shift as the view angle increases. Emission spectra depending on a transmittance of semitransparent cathode show a shift of peak wavelength from 515nm to 593nm. At this time, the full width at half maximum was about to be a constant of 50nm. With this kind of microcavity effect, we were able to control the emission spectra from the top-emission organic light-emitting diodes.

• 전기화학회지
• /
• 제22권2호
• /
• pp.60-68
• /
• 2019

이차 전지의 고전압 구동은 기존 셀 구조의 변화 없이도 고용량을 구현할 수 있는 유용한 접근 방법 중에 하나이나, 전극 표면에서의 극심한 부반응과 전극 활물질의 구조 붕괴 등과 같은 문제를 야기하게 된다. 본 연구에서는 니켈-망간-코발트 삼성분계(NCM) 활물질을 도입한 양극의 고전압 구동을 위해 원자층 증착법 (Atomic Layer Deposition, ALD)을 통해 전극판 표면에 $Al_2O_3$와 ZnO층으로 구성된 코팅 층을 형성하였다. 기존 ALD법으로 제조되는 박막에 비해 유사한 조건에서도 두꺼운 Al-doped ZnO (AZO)층을 최초로 형성하였고, 코팅된 AZO층의 두께를 달리한 NCM 기반의 양극판을 제조하였다. ALD 코팅된 양극이 도입된 코인셀을 제조하여 두껍게 형성된 코팅 층의 두께에 따른 고전압에서 충방전 거동을 확인하였다.

• 한국세라믹학회지
• /
• 제47권1호
• /
• pp.61-65
• /
• 2010

Ultrathin atomic layer deposition (ALD) coatings were found to enhance the performance of lithium-ion batteries (LIBs). Previous studies have demonstrated that $LiCoO_2$ cathode powders coated with metal oxides with thicknesses of $\sim100-1000{\AA}$ grown using wet chemical techniques improved LIB performance. In this study, $LiCoO_2$ powders were coated with conformal $Al_2O_3$ ALD films with thicknesses of only $\sim3-4{\AA}$ established using 2 ALD cycles. The coated $LiCoO_2$ powders exhibited a capacity retention of 89% after 120 charge-discharge cycles in the 3.3~4.5 V (vs. $Li/Li^+$) range. In contrast, the bare $LiCoO_2$ powders displayed only a 45% capacity retention. This dramatic improvement may result from the ultrathin $Al_2O_3$ ALD film acting to minimize Co dissolution or to reduce surface electrolyte reactions.

• 반도체디스플레이기술학회지
• /
• 제5권3호
• /
• pp.23-27
• /
• 2006

Recently, Top emission organic light-emitting diode (TEOLED) has been attracted by their potential application for the development of flat panel display (FPD). We have fabricated the high luminance top emission organic-emitting diode (TEOLED) using dual cathode layer and three top emitting structure. These devices were characterized by electroluminescence (EL) and current density-voltage (J-V) measurements. After compared it with Au anode structure, luminance of the device using dual anode was better than using without Al device. Consequently, Al layers are very good candidates for a promising electron-injecting buffer layer for top emission light-emitting diode (TEOLED).

• Bulletin of the Korean Chemical Society
• /
• 제30권8호
• /
• pp.1733-1737
• /
• 2009

A new cathode material based on Li$Ni_{0.8}Co_{0.15}Al_{0.05}O_2$ (LNCA)/polyaniline (Pani) composite was prepared by in situ self-stabilized dispersion polymerization in the presence of LNCA. The materials were characterized by fourier transform infrared spectroscopy (FT-IR), ultraviolet-visible spectroscopy (UV-Vis), X-ray diffraction (XRD), and scanning electron microscopy (SEM). Electrochemical properties including galvanostatic charge-discharge ability, cyclic voltammetry (CV), capacity, cycling performance, and AC impedance were measured. The synthesized LNCA/Pani had a similar particle size to LNCA and exhibited good electrochemical properties at a high C rate. Pani (the emeraldine salt form) interacts with metal-oxide particles to generate good connectivity. This material shows good reversibility for Li insertion in discharge cycles when used as the electrode of lithium ion batteries. Therefore, the Pani coating is beneficial for stabilizing the structure and reducing the resistance of the LNCA. In particular, the LNCA/Pani material has advantageous electrochemical properties.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 춘계학술대회 논문집
• /
• pp.20-21
• /
• 2008

Photovoltaic effects in organic solar cell were studied in a cell configuration of ITO/PEDOT:PSS/CuPd(20nm)/$C_{60}$(40nm)/BCP/Al(150nm) at room temperature. Here, the BCP layer works as an exciton blocking layer. The exciton blocking layer must transport electrons from the acceptor layer to the metal cathode with minimal increase in the total cell series resistance and should absorb damage during cathode deposition. Therefore, a proper thickness of the exciton blocking layer is required for an optimized photovoltaic cell. Several thicknesses of BCP were made between $C_{60}$ and Al. And we obtained characteristic parameters such as short-circuit current, open-circuit voltage, and power conversion efficiency of the device under the illumination of AM 1.5.