• 공업화학
• /
• 제23권6호
• /
• pp.534-538
• /
• 2012

$ Na^+$-beta-alumina 고체전해질을 고상반응법을 통해 합성하였으며, 두 종류의 안정화제 $Li_2O$와 MgO가 상 형성 및 소결밀도에 미치는 영향을 비교 분석하였다. 합성온도에 따른 ${\beta}/{\beta}^{{\prime}{\prime}}$-alumina 상 분율 분석을 위해, [$Na_2O$] : [$Al_2O_3$] = 1 : 5의 고정된 몰 비에서 하소온도를 $1200{\sim}1500^{\circ}C$로 변화하여, 각각 2 h동안 하소하였다. $Li_2O$를 안정화제로 사용한 경우에는 $1500^{\circ}C$에서 2차 상 전이가 발생해 ${\beta}^{{\prime}{\prime}}$-alumina 상 분율의 증가가 나타났지만, MgO를 첨가했을 때는 하소온도에 관계없이 상 분율이 유지되었다. 또한 disc 형태의 $Na^+$-beta-alumina 샘플을 $1550{\sim}1650^{\circ}C$의 온도에서 각각 30 min 소결한 후 상대 소결밀도, 상 변화 및 미세구조를 분석하였다. $Li_2O$를 안정화제로 사용하였을 때, 소결온도 $1600^{\circ}C$에서 ${\beta}^{{\prime}{\prime}}$-상 분율과 상대밀도가 각각 94.7%와 98%로 가장 높은 값을 나타냈으며, MgO를 안정화제로 사용하였을 경우, 소결온도의 증가에 따라 상대밀도가 크게 증가하는 결과를 보였다.

• 한국세라믹학회지
• /
• 제20권1호
• /
• pp.49-54
• /
• 1983

The main object of this study is to investigate the effect of Al powder as an additive on the sintering of calcined alumina comparing with that of calcined alumina alone. The degree of Al oxidation is calculated by measuring the weight increase during the firing Water absorption bulk density and compressive strength of the $Al_2O_3+Al$ system at each temperature are compared with those of $Al_2O_4$ alone. The $Al_2O_3+Al$ system shows better physical propeties than Al2O3 alone and it seems by the SEM observation that the fine oxidized Al particles(fine $Al_2O_3$ particles submicron unit) fill the interstices of the original $Al_2O_3$ par-ticles and thus result in the well-close-packed arrangement of the particles.

• 한국세라믹학회지
• /
• 제46권3호
• /
• pp.295-300
• /
• 2009

The crystal structure of surface coatings on Al1050 alloy by PEO (Plasma Electrolytic Oxidation), were investigated. The electrolyte for PEO was Na-Si-P system solution. The main crystalline phase were $\gamma$-alumina and $\alpha$-alumina. Crystallinity was increased with applied voltage and applied time. The dominant crystalline phase were affected not only chemical composition of Al alloy substrate and electrolyte, but also the +/- ratio of applied voltage.

• 한국세라믹학회지
• /
• 제30권7호
• /
• pp.571-577
• /
• 1993

The effect of $\alpha$-Al2O3 seeding on preparation of zirconia/alumina gel fragment prepared by sol-gel processing was characterized through XRD, SEM, TG/DTA and IR analysis. Aluminum isopropoxide and zirconium butoxide were used as starting materials. $\alpha$-Al2O3 seeding restrained grain growth of alumina and zirconia, and decreased tetragonal to monoclinic phase transformation of zirconia on cooling. Therefore, fine zirconia-toughened alumina composite having the relative sintered density of about 98% of theoretical at 140$0^{\circ}C$ for 2h could be obtained.

• 한국지구과학회지
• /
• 제25권1호
• /
• pp.39-47
• /
• 2004

In the FMAS system the effect of iron on alumina solubility in orthopyroxene has been determined by experiments with crystalline starting mixtures of garnet and orthopyroxene of known initial compositions at 20 kb, 975$^{\circ}C$ and 25 kb, 1,200$^{\circ}C$. These data have been modeled to develop a thermodynamic method for the calculation of Al$_{2}$O$_{3}$ in orthopyroxene as a function of P, T and composition. The direct application of the alumina solubility data in the MAS system to natural assemblages could lead to significant overestimation of pressure, probably by about 5kb for the relatively common garnet-lherzolites with abot 25 mol per cent Ca + Fe$^{2+}$ in garnet and about 1 wt. per cent Al$_{2}$O$_{3}$ in orthopyroxene since the effect of Fe is similar to that of Ca and Cr$^{3+}$in reducing the alumina solubility in orthopyroxene in equilibrum with garnet relative to that in the MAS system.

• 한국표면공학회지
• /
• 제27권1호
• /
• pp.29-35
• /
• 1994

The effects of coating of 3$\mu\textrm{m}$ thickness on the mechanical property of alumina after heat treatment at 100$0^{\circ}C$ for 30minutes under $10^{-6}$torr vacuum was quantified in terms of modulus of rupture(MOR) using Weibull plot. While the copper coating did not change MOR of alumina due to the nonwetting behavior of Cu on $Al_2O_3$, the reactive titanium metal coating caused a noticeable 29% reduction in averaged MOr strength. This was related with the combined effects of microcracks in coating formed during heat treatment and good bonding character between Ti and $Al_2O_3$. The effect of cosputtering of Ti and Cu, bilayer coatings of Cu/Ti and Ti/Cu were also investigated. It was found that Ti, cosputtered, Cu/ti and Ti/Cu coatings reduced MOR strength of alumina in the order listed. This was correlated with the amount of Ti at coating/alumina inter-face associated with a coated layer or segregation of Ti during heat treatment.

• 센서학회지
• /
• 제14권3호
• /
• pp.206-210
• /
• 2005

The SOI structure with buried alumina was fabricated by ALD followed by bonding and etchback process. The interface of alumina and silicon was analyzed by CV measurements and cross section was investigated by SEM analysis. The density of interface state of alumina and silicon was 2.5E11/$cm^{2}$-eV after high temperature annealing for wafer bonding. It was confirmed that the surface silicon layer was completely isolated from substrate by cross section SEM and AES depth profile. The device on this alumina SOI structure would have better thermal properties than that on conventional SOI due to higher thermal conductivity of alumina than that of silicon dioxide.

• 공학논문집
• /
• 제3권1호
• /
• pp.215-222
• /
• 1998

촉매 연소용 촉매 담체인 $\gamma-Al_2O_3$ 분말의 열안정화에 미치는 La과 Si의 첨가 효과에 대하여 연구하였다. 첨가제의 첨가는 습식 impregnation방법으로 행하였고, 출발 물질은 $La(NO_3)_3{\cdot}6H_2O$와 $Si(OC_2H_5)_4$를 사용하였다. 열안정화 효과는 혼합분말을 고온에서 열처리 한 후 비표면적을 측정하여 고찰하였다. 첨가제로 첨가한 La과Si는 모두 순수한 $\gamma-Al_2O_3$분말에 비하여 소결을 억제함으로써 열 안정화 효과가 있음이 확인되었으며, 특히 Si 첨가한 경우에는 $\alpha-Al_2O_3$의 생성을 현저히 억제한다는 것을 확인하였다. 이들 첨가제에 의한 열안정화 효과는 첨가제에 의한 새로운 상의 생성과 표면 확산의 억제등이 주된 요인으로 판단되었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.81-81
• /
• 2009

Non-sintered Alumina films were fabricated via inkjet printing processes without a high temperature sintering process. The packing density of these inkjet-printed alumina films measured around 60%. Polymer resin was infiltrated thru these non-sintered films in order to fill out the 40% of voids constituting the rest of the inkjet-printed films. The concept of inkjet-printed Alumina-Resin hybrid materials was designed in order to be applicable to the ceramic package substrates for 3D-system module integration which may possibly substitute LTCC-based 3D module integration. So, the dielectric properties of these inkjet-printed $Al_2O_3$ hybridmaterialsareofourgreatinterest. We have measured dielectric constant and dissipation factor of the inkjet-printed $Al_2O_3$-resinhybridfilmsbyvaryingtheamountofresininfiltratedthruthe$Al_2O_3$films.

• 전기화학회지
• /
• 제25권4호
• /
• pp.191-200
• /
• 2022

Na-β"-Al₂O₃ has been widely employed as a solid electrolyte for high-temperature sodium (Na) beta-alumina batteries (NBBs) thanks to its superb thermal stability and high ionic conductivity. Recently, a vapor phase conversion (VPC) method has been newly introduced to fabricate thin Na-β"-Al₂O₃ electrolytes by converting α-Al₂O₃ into β"-Al₂O₃ in α-Al₂O₃/yttria-stabilized zirconia (YSZ) composites under Na⁺ and O^2- dual percolation environments. One of the main challenges that need to be figured out is lowered conductivity due to the large volume fraction of the non-Na⁺-conducting YSZ. In this study, the effect of lithia addition in the β"-Al₂O₃ phase on the grain size and ionic conductivity of Na-β"-Al₂O₃/YSZ solid electrolytes have been investigated in order to enhance the conductivity of the electrolyte. The amount of pre-added lithia (Li₂O) precursor as a phase stabilizer was varied at 0, 1, 2, 3, and 4 mol% against that of Al₂O₃. It turns out that ionic conductivity increases even with 1 mol% lithia addition and reaches 67 mS cm^-1 at 350 ℃ of its maximum with 3 mol%, which is two times higher than that of the undoped composite.