• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1661-1663
• /
• 2000

This study was to measure the dielectric characteristics of 0.05Pb($Al_{0.5}Nb_{0.5}$)-0.95Pb($Zr_{0.52}Ti_{0.48})O_3$[PAN-PZT] system ceramics according to the variation of $Cr_{2}O_3$, $Fe_{2}O_3$ addition amount. 0.0$\sim$1.2[wt%] and according to sintering temperature after creating the specimens with a general sintering way. The results of this study were summarized as follows : the dielectric constant at 20[$^{\circ}C$] reduced dy increasing additive on the whole. The dielectric loss was minimum value of 12.77[%], sintered at 1200[$^{\circ}C$], dopped with $Cr_{2}O_3$ 0.3[wt%] and minimum value of 10.89[%], sintered at 1200[$^{\circ}C$], dopped with $Fe_{2}O_3$ 0.6[wt%]. The variation rate of dielectric constant according to the change of frequency was decreased slowly by increasing frequency. The temperature coefficient of capacitance turned out increasing the stability of the temperature, decreased $Cr_{2}O_3$ 0.3wt% showed its minimum value 0.59[%/$^{\circ}C$], the maximum value 0.9[%/$^{\circ}C$] with $Cr_{2}O_3$ 3wt%.

• Korean Journal of Materials Research
• /
• v.5 no.5
• /
• pp.598-605
• /
• 1995

Thin films of $YB_{2}Cu_{3}O_{7-d}$ were prepared on various substrated of MgO(100), $SrTiO_{3}$, and $LaAlO_{3}$ by using off-axis magentron sputtering methods and annealing in-situ. The prarameters of film fabrication processes had been optimized through a "follow the lcoal maxima" strategy to yield good quality films in therms of the critical temperature $T_{c}$ and the critical current density $J_{c}$. Optimizedproecsses employing a plane magndtron and an cylindrical magnetron yielded $T_{c}$>90K along with $J_{c}$$10^{6}$A/$\textrm{cm}^2$ at 77K and > 2${\times}$$10^{7}$A/$\textrm{cm}^2$ at 5K. The sampels, however, showed degradationinthe properties, after chemical etching for fabrication of microbridges with the line width of 2-10 mocrons. In particular, the value of $T_{c}$ for the microbridges of 2microns was as small as 80%. The degradation was strongly dependent on the line width through a formula : $T_{c}$(e)=$T_{c}$)b) [1-a exp(-1000 bL)} where $T_{c}$(e) and $T_{c}$ (b) are the values of $T_{c}$ in the absolute scale measured after and before chemical etching, respectively and L is the line width in mm. By utilizing a best fitting technique, the proper constant values of a and to b were found as exp(-1.2) and 0.22, respectively. This formula was very useful in estimatiing the upper limit of the device operationtemperature.

• Journal of Power System Engineering
• /
• v.2 no.3
• /
• pp.49-54
• /
• 1998

This paper is investigated of hardness and adhesiveness of plasma sprayed coating steels by AE(Acoustic Emission) testing when loading a tensile. AE Parameters used are Event, Count, Energy and Amplitude. Test specimens are carbon steel(S45C) with sprayed coating layers of Ni-4.5wt.%Al(bond coating) and $TiO_2$(top coating), and carry out heat treatment at $800^{\circ}C\;and\;1000^{\circ}C$, respectively. The micro-hardness of the heat treatment specimen have been improved more than that of non-heat treatment. On the tensile test, the process and occurence of the exfoliation of the sprayed coating layer can be estimated by AE Characteristics of AE parameters, such as event, count, amplitude and energy, on the layer exfoliation are shown the similar aspects. The exfoliation of bond coating occure at about 20% of strain and top coating is about 5% of strain.

• Journal of the Korean earth science society
• /
• v.21 no.5
• /
• pp.595-610
• /
• 2000

This study has been designed to elucidate the petrography and geochemical characteristics of the volcanic rocks and focused on petrogenesis and tectonic environment of the Bokyeongsa volcanics in the northeast Gyeongsang Basin. The Bokyeongsa volcanics consist of the Naeyeonsan tuff which include rock fragment plagioclase, quartz and hornblende and pumice showing welded structures, and felsite. According to the petrochemical data, the Naeyeonsan tuff and felsite are in the range of 68${\sim}$71wt% and 77wt% SiO$_2$ content respectively. The Naeyeonsan tuff belongs to dacite/rhyodacite, and felsite to rhyolite. These volcanics rocks belong to the calc-alkaline rock series on the TAS diagram and the AFM diagram. The variations of major elements of the volcanic rocks show that contene of TiO$_2$, Al$_2$ O$_3$, FeO$^T$, MnO, MgO, CaO are inversely proportional to those of SiO$_2$, but contents of K$_2$O are positively. They represent differentiation trend of calc-alkaline rocks series. In spider disgram of MORB-normalized trace element partterns, contents of K, Rb, Th and Ta are relatively high, but those of Nb, Zr, Hf, Ti, Y and Yb are nearly similar to MORB. In the chondrite-normalized REE patterns, light REEs are more enriched than heavy REEs. The trace element composition and REE patterns suggest that they are typical island-arc calc-akaline volcanic rocks formed in the tectonomagmatic environment of subduction zone under continental margin.

• Progress in Superconductivity and Cryogenics
• /
• v.13 no.4
• /
• pp.22-25
• /
• 2011

A single-coat $YBa_2Cu_3O_{7-{\delta}}$ (YBCO) film of high critical currents ($I_c$) could be successfully fabricated by optimizing the viscosity of the coating solution in the metal-organic deposition (MOD) process. From a Ba-deficient coating solution (Y: Ba: Cu = 1: 1.5: 3) having the viscosity of 212 $mPa{\cdot}sec$, 0.9 ${\mu}m$-thick single coat YBCO film with the $I_c$ value of 289 A/cm-width ($J_c$ = 3.2 MA/$cm^2$) at 77 K was achievable on the $SrTiO_3$ (STO) substrate, which was superior to that of our previous report for 0.8 ${\mu}m$-thick single coat YBCO film from a stoichiometric coating solution (Y: Ba: Cu = 1: 2: 3) on the $LaAlO_3$ (LAO) substrate. This result might be attributed to denser and more homogeneous microstrcuture in the case of the YBCO film from the Ba-deficient coating solution.

• Economic and Environmental Geology
• /
• v.56 no.3
• /
• pp.239-257
• /
• 2023

Sangdong deposit, a W-Mo skarn deposit, is located in Taebaeksan mineralized district, hosting vertically developed scheelite-quartz veins that formed at the late ore-forming stage. In this study, we tried to examine the geochemical signatures of ore-forming fluids and vein-forming mechanisms by analyzing the micro-texture of quartz veins and trace element concentrations of quartz. As a result of texture analyses, quartz veins in the hanging wall orebody and the foot wall orebody commonly exhibit the blocky and the elongate blocky texture, respectively, whereas quartz veins in the main orebody show both textures. These textural differences indicate that quartz veins from the hanging wall orebody were precipitated by the primary hydrofracturing due to H₂O saturation in the igneous body with relatively high temperature and pressure at a vein-skarn stage, and after that, repeated hydrofracturing caused the formation of quartz veins from the main orebody and foot wall orebody. The results of trace element concentrations show that Li⁺+Al³⁺↔Si⁴⁺ is a main substitution mechanism. However, those of the foot wall orebody were clearly divided into a Li⁺-dominated substitution and a Na⁺-, K⁺-dominated substitution. Considering that quartz veins from the foot wall orebody commonly show the elongate blocky texture, such a distinction means that it is a result of repeated injections of fluid with the different composition. Ti concentrations of quartz from the hanging wall, main, and the foot wall orebody are 28.6, 8.2, and 15.7 ppm in average, respectively. Given a proportional relationship between the precipitation temperature and Ti concentrations, it seems that quartz veins from the hanging wall orebody were precipitated at the highest temperature. Al concentrations of the hanging wall, main, and the foot wall orebody having an inverse relationship with fluid pH are 162.3, 114.2, and 182.5 ppm in average, respectively. These results show that Al concentrations in vein-forming fluids were not changed dramatically. Moreover, these concentrations are extremely low in comparison with the other hydrothermal deposits. This indicates that quartz in overall ore veins at Sangdong deposit was precipitated from the constant condition with slightly acidic to near neutral pH.

• Journal of the Speleological Society of Korea
• /
• v.34 no.35
• /
• pp.32-42
• /
• 1993

The Paektu-san mountains are geographically situated in the Korea strait to the north of the main peninsula, coordinated between the longitudes of W(127$^{\circ}$15'~128$^{\circ}$00')and E(128$^{\circ}$15'~129$^{\circ}$00'), and between the latitudes of S(41$^{\circ}$15'~42$^{\circ}$00') and N(42$^{\circ}$10'~42$^{\circ}$40'). The volcanic group of the Paektu-san mountains can be devided into 2 main kinds of volcanos by the method investigation, The ashes are mainly made of tremolite, trachte, basalt and pumice, or, a little quartz, labradorite and volcanic glass. These sorts, ratios and forms of the rocks are respectively similar. The Haeven lake is surrounded by 19 peaks. The central volcanic cone is a secant cone in shape, with an altitude of the 1800m to 2749,2m (Chang-kun-bong), an average diameter of 10km, and a shape of an ellipse seen high from the plane. They say there were several eruptions in 1668, 1700 and 1702 A. D. The crystal structure of the rock sample collected at the cave of Mt. Paektu-san is monoclinic. The quantitative analysis of the rock samples in the cave is done by using XRF this time. The chemical compositions by XRF fundamamental parameter analysis is : SiO$_2$: 50.72Wt%, TiO = 2.422Wt%, $Al_2$O$_3$= 17.65Wt%, Fe$_2$O$_3$= 9.371Wt%, CaO = 8.711Wt%, MgO = 4.l19Wt%, MnO = 0.l15Wt%, $K_2$O = 1.369Wt%, Na$_2$O : 3.028Wt% and P$_2$O$_{5}$ = 0.365Wt%. The K-Ar age of the rock sample is also determined to be 0.16Ma. This paper describes some problems experienced in dating young volcanic rocks, and then discusses chemical compositions, X-ray fluorescence analyses and the age of the formation of a lava tunnel such as in Mt. Paektu-san.n.

• Structural Engineering and Mechanics
• /
• v.76 no.5
• /
• pp.561-578
• /
• 2020

The present work addresses the surface integrity and chip morphology in finish hard turning of AISI D3 steel under nanofluid assisted minimum quantity lubrication (NFMQL) condition. The surface integrity aspects include microhardness, residual stress, white layer formation, machined surface morphology, and surface roughness. This experimental investigation aims to explore the feasibility of low-cost multilayer (TiCN/Al2O3/TiN) coated carbide tool in hard machining applications and to assess the propitious role of minimum quantity lubrication using graphene nanoparticles enriched eco-friendly radiator coolant based nano-cutting fluid for machinability improvement of hardened steel. Combined approach of central composite design (CCD) - analysis of variance (ANOVA), desirability function analysis, and response surface methodology (RSM) have been subsequently employed for experimental investigation, predictive modelling and optimization of surface roughness. With a motivational philosophy of "Go Green-Think Green-Act Green", the work also deals with economic analysis, and sustainability assessment under environmental-friendly NFMQL condition. Results showed that machining with nanofluid-MQL provided an effective cooling-lubrication strategy, safer and cleaner production, environmental friendliness and assisted to improve sustainability.

• Korean Journal of Heritage: History & Science
• /
• v.46 no.4
• /
• pp.108-125
• /
• 2013

This study examined the actual reconstruction drawing, composite mineral, particle size and property test, fine organic matters, color differences and main ingredients of the earthen mold excavated in Dongcheon-dong, Gyungju. The cross-section of the inner mold and outer mold divides into inside (1st layer) and outside (2nd layer), with organic matters mixed outside. The cross-section has been altered due to heat and form removal agent. X-ray analysis revealed that the layer was made of minerals with high transmissivity and only quartz particles were observed through a polarizing microscope. The inside of cross-section in SEM observation identified enlarged air gap, with crack developed in the center, but no changes observed on the outside. The particle size of the composites is almost the same for the inner mold and outer mold and is silt clay loam. The ratio between silt clay and silt clay loam was about 2.7:1 and 2.9:1 respectively. In the property test, the density and absorption rate of inner mold and outer mold were similar, but porosity was different, with inner mold of 27.36% and outer mold of 31.09%. The color difference of cross-section seems to have been caused by the spread of soot on the 1st layer surface for removal of form or by the covering of ink to protect the 1st layer. Composite mineral analysis revealed the same composition for the inner mold and outer mold, except for the magnetite that was detected in the inner mold alone. As for the main ingredient analysis, the average content of $SiO_2$ was 71.64% and that of $Al_2O_3$ was 14.59%. As for the sub-ingredients, $Fe_2O_3$ was 4.51%, $K_2O$ 3.06%, $Na_2O$, MgO, CaO, $TiO_2$, $P_2O_5$ and MnO was less than 2%.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.5
• /
• pp.427-431
• /
• 2020

In this research, we evaluated the electrical properties of polycrystalline-gallium-oxIde (Ga₂O₃) thin films grown by mist-CVD. A 500~800 nm-thick Ga₂O₃ film was used as a channel in a fabricated bottom-gate MOSFET device. The phase stability of the β-phase Ga₂O₃ layer was enhanced by an annealing treatment. A Ti/Al metal stack served as source and drain electrodes. Maximum drain current (I_D) exceeded 1 mA at a drain voltage (V_D) of 20 V. Electron mobility of the β-Ga₂O₃ channel was determined from maximum transconductance (g_m), as approximately, 1.39 ㎠/Vs. Reasonable device characteristics were demonstrated, from measurement of drain current-gate voltage, for mist-CVD-grown Ga₂O₃ thin films.