• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.227-230
• /
• 1999

In this paper, the machining characteristics of high speed ball end milling affected by the rotational error of high speed spindle using air bearing are investigated. The error motions of a spindle have generally influenced on the surface roughness, the form accuracy, the tool life, etc. in end milling. Experiments are carried out over a wide range of rotational speeds(10,000-50,000rpm). The rotational errors of the spindle are measured by the gap sensor mounted on the spindle shaft at various cutting speeds. The relations between the surface roughness and the spindle error motion are presented. Results show that the rotational accuracy of the spindle directly affects the surface roughness of the machined surface.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 B
• /
• pp.992-994
• /
• 2004

In this paper, hybrid electromagnets using NdFeB permenant magnet are designed by 3-dimensional finite element analysis. Four hybrid magnets levitate the carrier of which total weight including control circuits and battery is 14[kg]. The nominal air gap length of the hybrid magnet is 3[mm]. The control circuit consists of DSP, 4-quadrant chopper, and gap sensor as feedback sensors. As a result, some experimental results for the magnetic levitation control by PI feedback control theory are shown.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2011년도 춘계학술대회
• /
• pp.777-778
• /
• 2011

본 논문에서는 높은 신뢰성과 긴 수명을 특징으로 하는 저가형 센서로 마그네틱 픽업코일 방식의 자기유도작용을 이용한 수동형 차륜 속도센서를 제작하여 그 특성을 분석하였다. 제작된 수동형 차륜 속도센서는 직접적인 유도 기전력을 감지하여 유도하는 Pole piece, 영구자석과 Bobbin역할을 하는 내피와 코일로 구성된 센서부, 세서를 보호하고 외부 노이즈를 제거하는 외피부, 그리고 센서를 보강 및 고정하기 위한 플랜지부로 구성된다. 제작된 센서를 기성품과 특성을 비교, 분석하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 B
• /
• pp.1029-1031
• /
• 2005

A magnetic position sensor is a apparatus that detect the rotating position by measuring the value of the flux density of the rotating position. In this paper, the magnetization system of the permanent magnet in the magnetic position sensor which detects the rotating position was designed. The permanent magnet was magnetized for the flux density into the hole element to be sinusoidal distribution according to the rotating position. To make the sinusoidal distribution of flux density, the magnetization values according to the position in permanent magnet were varied by adjusting the air gap between the pole of the magnetization fixture and the surface of the permanent magnet.

• 한국전기전자재료학회논문지
• /
• 제26권9호
• /
• pp.669-676
• /
• 2013

In this study, we introduce a polymer(polyimide) based pressure sensor to measure real-time heart beat and blood pressure. The sensor have been designed with consideration of skin compatibility of material, cost effectiveness, manufacturability and wireless detection. The designed sensor was composed of inductor coils and an air-gap capacitor which generate self-resonant frequency when electrical source is applied on the system. The sensor was obtained with metalization, etching, photolithography, polymer adhesive bonding and laser cutting. The fabricated sensor was shaped in circular type with 10mm diameter and 0.45 mm thickness to fit radial artery. Resonant frequencies of the fabricated sensors were in the range of 91~96 MHz on 760 mmHg pressurized environment. Also the sensor has good linearity without any pressure-frequency hysteresis. Sensitivity of the sensor was 145.5 kHz/mmHg and accuracy was less than 2 mmHg. Real-time heart beat measurement was executed with a developed hand-held measurement system. Possibility of real-time blood pressure measurement was showed with simulated artery system. After installation of the sensor on skin above radial artery, simple real blood pressure measurement was performed with 64 mmHg blood pressure variation.

• 한국전기전자재료학회논문지
• /
• 제19권5호
• /
• pp.405-410
• /
• 2006

We fabricated gas sensors using carbon nanotubes (CNTs) as electron emitters for the purpose of detecting inert gases. By using the silicon-glass anodic bonding and glass patterning technologies with the typical Si process, we improved the compactness of the sensors and the reliability in process. The proposed sensor, based on, an electrical discharge theory known as Paschen's law in principle, works by figuring the variation of the discharge current depending on gas concentration. In the experiment, the initial breakdown characteristics were measured for air and Ar as a function of gas pressure. As the result, even though it should be realized that there are many other factors which have an effect on the breakdown of a gap, the sensors led to similar result as predicted by Paschen's law, and they showed a possibility as gas sensors which enable to detect the gas density ranged to the vacuum pressure from 1 to $10^{-3}$ Torr.

• 한국철도학회논문집
• /
• 제19권4호
• /
• pp.468-479
• /
• 2016

고압 전선 등에 장착된 시스템에 전원을 공급하기 위해서는 절연 이격 거리 이상의 거리에 무선으로 수십 Watt 급의 전력을 보낼 수 있는 시스템이 필요하다. 이러한 무선 전력 전송 시스템은 대개 코일의 크기가 10cm 이상의 대형이다. 본 연구에서는 이처럼 대형 코일을 Printed circuit board를 이용해 제작할 경우 발생하는 손실 발생원 들을 분석하고 그 중 가장 주요한 손실원인이 Dielectric loss 라는 것을 밝혔다. 또한 이 dielectric loss를 최소화 하기 위해서 PCB의 재질 선정 방법 및 Distributed tuning capacitor method를 제시해 $40cm{\times}40cm$ 크기의 4턴 및 5턴 코일의 설계 방법을 제시했고, 실험을 통해 Quality factor를 300 이상으로 만들 수 있음을 보였다.

• 한국공작기계학회논문집
• /
• 제17권4호
• /
• pp.51-58
• /
• 2008

This paper presents a new design of the precision stage for the reticle in lithography process and a low hunting control method for the stage. The stage has three axes for X, Y, ${\theta}_z$ those actuated by three voice coil motors individually. The designed reticle stage system has three gap sensors and voice coil motors, and supported by four air bearings and the forward/inverse kinematics of the stage were solved to get an accurate reference position. When a stage is in regulating control mode, there always exist small fluctuations(stage hunting) in the stage movement. Because the low stage hunting characteristic is very important in recent lithography and nano-level applications, a special regulating controller for ultra low hunting is proposed in this paper. Also this research proposed the 2-step transmission system for preventing the noise infection from environmental devices. The experimental results showed the proposed regulating control system reduced hunting noise as 35nm(rms) when a conventional PID generates 77nm(rms) in the same mechanical system. Besides the reticle stage has 100nm linear accuracy and $1{\mu}rad$ rotation accuracy at the control frequency of 8kHz.

• Agricultural and Biosystems Engineering
• /
• 제1권1호
• /
• pp.49-53
• /
• 2000

A magnet assembly is a critical element of a nuclear magnetic resonance(NMR) based sensor. Magnetic flux density and homogeneity are essential to its optimum performance. Geometry and magnet material properties determine the magnetic flux density and homogeneity of the assembly. This study was carried out to develop the design for a magnet assembly. A 2-D finite element model for the magnetic assembly was developed using ANSYS and evaluated the effects of adding shimming frames and steel bars in the corners of the rectangular steel cover which surrounded the magnet. The assembly was manufactured and evaluated. According to the ANSYS model, modified pole frames increased magnetic flux density by 8.3% and increased homogeneity by 83%. Addition of steel bars in the corners increased the magnetic flux density by 1%, and improved homogeneity up to three times. The difference between simulated and measured magnetic flux densities at the center point of the air gap was within 2.4%.

• 한국정밀공학회지
• /
• 제21권12호
• /
• pp.119-126
• /
• 2004

Permanent magnetic gears are magneto-mechanical devices that are widely used to replace the ordinary mechanical gear and to transmit torque without the mechanical contact. This study investigates the characteristics of touch free permanent magnetic gear according to the employing systems. The effect of the magnetic torque is analyzed by using 3 dimensional Finite Element Method (FEM). To estimate the transmission torque of FEM model, the numerical results are compared with the experimental results. The influences of geometry size, magnet number on transmission torque are obtained. As results of this paper, it is confirmed that the transmission torque behavior is associated with the configuration of the magnet numbers and the air gap between the two permanent magnetic gears.