• Journal of Advanced Marine Engineering and Technology
• /
• 제25권5호
• /
• pp.1148-1160
• /
• 2001

An electronic control system of the automobile engine for optimal start and idle speed control has been developed. This system employs the microcoputer-based electronic control unit and crank angle sensor for precise control on fuel injection, ignition timing, and idle speed more quickly and accurately at the start and idling. Consequently, the number of misfire can be reduced during been affected by air flow rate, idle quality(roughness), spark timing, fuel injection, water temperature, and load, Thus, this electronic control system strivers to reach the optimal idle operating point, defined the lowest idle speed(fuel economy) and idle quality(roughness), under any engine operating conditions.

• 한국동물번식학회:학술대회논문집
• /
• 한국동물번식학회 2002년도 춘계학술발표대회 발표논문초록집
• /
• pp.52-52
• /
• 2002

The objective of this study was to determine the developmental competence of in vitro matured bovine oocytes after intracytoplasmic sperm injection(ICSI) with frozen-thawed epididymal spermatozoa. The ovaries were obtained from slaughtered Korean native cows. Oocytes matured in vitro for 24 hrs were fertilized by ICSI with frozen-thawed epididymal spermatozoa. After ICSI, one group of oocytes was activated with 7% ethanol for 5 min, and second group was not activated. The follicular oocytes were cultured in TCM-199 medium containing hormones and 10% FCS for 24-30 hrs in a incubator with 5% CO₂ in air at 38.5℃. (omitted)

• 한국연소학회지
• /
• 제16권1호
• /
• pp.52-57
• /
• 2011

The present study describes the characteristics of combustion and exhaust emissions in compression ignition engines using diesel-gasoline dual fuel. For investigating combustion characteristics, diesel fuel was injected directly in a single-cylinder compression ignition engine with a common-rail injection system and gasoline fuel was injected into a premixed chamber installed in an intake port. In order to investigate exhaust emission characteristics, exhaust gas was measured by emission analyzer and smoke meter. The experimental results showed that cases of diesel-gasoline dual fuel combustion exhibited extended ignition delay and reduced peak combustion pressure compared to those of directly injected diesel fuel cases. Furthermore, premixed gasoline-air mixture reduced NOx emissions due to low peak of rate of heat release(ROHR).

• 한국연소학회지
• /
• 제22권3호
• /
• pp.23-28
• /
• 2017

The fuel and oxidizer mixing process in the shock tube driven section is simulated numerically. The boundary condition is set based on an shock tube experimental condition. The objective is to predict the gas mixing time for experiments. In the experiment, the amount of fuel to be injected is determined in advance. Then, according to duration of fuel injection, 5 cases with the same fuel mass but different fuel mass flow rate are simulated. After fuel is injected into the driven section, the fuel and air will be mixed with each other through convection and diffusion processes. The mixing time is predicted numerically for experiments.

• 한국자동차공학회논문집
• /
• 제4권1호
• /
• pp.86-95
• /
• 1996

This study was on the pollution emissions of the Ultrasonic fuel feeding system in gasoline injection vehicle. This work measured th SMD of the fuel, and compared the characteristics through chassis dynamometer and highway road test by the conventional vehicle. And this work measured vacuum degree, turbulence intensity and the rate of fuel consumption according to intake air velocity with swirler. The results are as followed; The effects of the vehicle installed the ultrasonic fuel feeding system are better than those of the conventional vehicle.

• 한국자동차공학회논문집
• /
• 제12권2호
• /
• pp.17-23
• /
• 2004

A cylindrical constant volume combustion bomb is used to investigate the combustion characteristics and to analyze the heat quantity of homogeneous charge methane-air mixture under various initial pressures, excess air ratios and ignition times. As the overall pressure increase, the values of maximum combustion pressure, maximum heat release rate and cumulative heat release have been increased. But it is not very meaningful to compare with some values such as maximum combustion pressure, maximum heat release rate and cumulative heat release for different overall pressure due to the different heat energy of supplied fuel. So the each value is needed to be compared with normalized value, which is divided by the entered fuel energy. To analyze the heat quantity, some definitions including the CHR ratio, the UHC ratio and the HL ratio are needed and are calculated. As the overall pressure increase, the CHR ratios and the UHC ratios have been decreased, while the HL ratios have been increased. The CHR ratio of 300 ms has the higher value than that of 10000ms, and the HL ratios of 300 ms have a lower value.

• 대한환경공학회지
• /
• 제38권6호
• /
• pp.323-328
• /
• 2016

공기주입형 가압식 MBR 공정은 일반적인 침지식 MBR 공정과 마찬가지로 정상 운전조건에서 막 오염에 대한 제어 및 관리 기술뿐만 아니라 저유량, 저부하 조건과 같은 비정상 운전조건에서도 시설의 운영에 지장이 없도록 막 오염에 대한 제어 대책이 필요하다. $85m^3$/일 규모의 공기주입형 가압식 MBR 실증시설 운영을 통해 공기주입에 의한 분리막 오염 저감효과와 비상 시 운전조건에서 미생물에 의해 나타날 수 있는 막 오염 문제를 고찰하였다. 가압식 분리막에서 공기의 주입은 분리막 표면에서 공기방울에 의한 scouring 효과에 의해 TMP 상승 기간을 연장시키고 처리의 안정성과 높은 효율의 플럭스($40L/m^2{\cdot}h$ 이상)를 장시간 유지할 수 있는 것으로 분석되었다. 비정상 운전조건에서는 생물반응조에 PACl (53 mg/L as Al)을 주입한 경우 19%의 TMP 상승 감소효과가 있었으나 MBR 공정의 비정상 운전조건 지속에 따른 반복적인 PACl의 주입은 질산화 미생물의 활성도에 영향을 미치게 되어 궁극적으로 질소 처리효율이 악화될 수 있음을 회분식 배양 실험을 통해 확인하였다. 생물반응조에 PAC (0.6 g/L)을 주입한 경우에서는 연속운전 5일 동안 TMP 상승 없이 운전 초기 TMP인 $0.2kg/cm^2$을 유지하여 안정적으로 운전이 가능하였다. 이것은 미생물의 성장 저해조건에서 막 오염 원인물질을 유발하는 EPS와 같은 고분자 물질의 흡착에 따른 것으로 판단된다.

• 대한기계학회논문집B
• /
• 제34권5호
• /
• pp.491-498
• /
• 2010

연료전지 자동차는 성능과 수명 측면에서, 전해질막의 가습이 필요하며, 이를 위해 반응기체인 공기, 수소의 높은 가습이 요구된다. 본 연구에서는 내경 75 mm공기공급관 내에 직접 삽입된 인젝터(노즐)과 액적제거를 위한 사이클론을 통한 가습장치를 고안하여 실험을 수행하였다. 충돌형 노즐 3 종류를 이용하여 분사압력, 공기 유량, 분사방향각도를 달리하여 실험을 수행하였다. 가습 성능을 분석하기 위해, 가습효율이라는 개념을 정의하였다. 별도의 외부 열공급원 없이 분사되는 물과 공기의 엔탈피가 자체 기화열 공급원으로, 분사되는 물의 양이 가습에 가장 중요한 변수임을 볼 수 있었다. 사이클론은 높은 공기유량에서 재비산이 발생되는 것을 볼 수 있었다. 노즐타입 PJ24, 분사방향 각도 90도, 분사압력 1200 kPa, 공기 유량 6000 nlpm에서 절대습도 $21.29\;kJ/kg_{da}$, 가습 효율 86.57%를 얻을 수 있었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2006년도 제26회 춘계학술대회논문집
• /
• pp.367-370
• /
• 2006

This paper deals with the modeling and simulation of the internal flowfield in a valveless airbreathing pulse detonation engine (PDE) currently under experimental development at the U.S. Naval Postgraduate School. The system involves no valves in the airflow path, and the isolation between the inlet and combustor is achieved through the gasdynamics in an isolator. The analysis accommodates the full conservation equations in axisymmetric coordinates, and takes into account variable properties for ethylene/oxygen/air system. Chemical reaction schemes with a single progress variable are implemented to minimize the computational burden. Detailed flow evolution during a full cycle is explored and propulsive performance is calculated. Effect of initiator mass injection rate is examined and results indicate that the mass injection rate should be carefully selected to avoid the formation of recirculation zones in the initial cold flowfield. Flow evolution results demonstrate a successful detonation transmission from the initiator to the combustor. However, strong pressure disturbance may propagate upstream to the inlet nozzle, suggesting the current configuration could be further refined to provide more efficient isolation between the inlet and combustor.

• 한국분무공학회지
• /
• 제15권3호
• /
• pp.131-139
• /
• 2010

Gas motion within the engine cylinder is one of the major factors controlling the fuel-air mixing and combustion processes in diesel engines. In this paper, a special swirl-chamber is designed and applied to a DI (direct injection) diesel engine to generate a strong swirl motion thus enhancing gas motion. Compression, combustion and expansion strokes of this DI diesel engine with the swirl-chamber have been simulated by CFD software. The simulation model was first validated through comparisons with experimental data and then applied to do the simulation of the spray and combustion process. The velocity and temperature field inside the cylinder showed the influences of the strong swirl motion to spray and combustion process in detail. Cylinder pressure, average temperature, heat release rate, total amount of heat release, indicated thermal efficiency, indicated fuel consumption rate and emissions of this DI diesel engine with swirl-chamber have been compared with that of the DI diesel engine with $\omega$-chamber. The conclusions show that the engine with swirlchamber has the characteristics of fast mixture formulation and quick diffusive combustion; its soot emission is 3 times less than that of a $\omega$-chamber engine; its NO emission is 3 times more than that of $\omega$-chamber engine. The results show that the DI diesel engine with the swirl-chamber has the potential to reduce emissions.