• 한국자동차공학회논문집
• /
• 제21권1호
• /
• pp.43-50
• /
• 2013

The stringent emission regulation and future shortage of fossil fuel motivate the research of alternative powertrain. In this study, a system of proton exchange membrane fuel cell has been modeled to analyze the performance of the fuel cell system for automotive application. The model is composed of the fuel cell stack, air compressor, humidifier, and intercooler, and hydrogen supply which are implemented by using the Matlab/Simulink(R). Fuel cell stack model is empirical model but the water transport model is included so that the system performance can be predicted over various humidity conditions. On the other hand, the model of air compressor is composed of motor, static air compressor, and some manifolds so that the motor dynamics and manifold dynamics can be investigated. Since the model is concentrated on the strategic operation of compressor to reduce the power consumption, other balance of components (BOP) are modeled to be static components. Since the air compressor model is empirical model which is based on curve fitting of experiments, the stack model is validated with the commercial software and the experiments. The dynamics of air compressor is investigated over unit change of system load. The results shows that the power consumption of air compressor is about 12% to 25% of stack gross power and dynamic response should be reduced to optimize the system operation.

• 한국자동차공학회논문집
• /
• 제10권1호
• /
• pp.115-124
• /
• 2002

The optimum design of auto-catalyst needs a good compromise between the pressure drop and flow distribution in the monolith. One of the effective methods to achieve this goal is to use the concept of radially variable cell density. However, there has been no study of evaluating the usefulness of this method on light-off catalyst. We have computationally investigated the effectiveness of variable cell density technique applied to the light-off catalyst using a three-dimensional integrated CFD model. in which transient chemical reacting calculations are involved. Computed results show that variable cell density technique can reduce the accumulated emissions of CO and HC during the early 100sec of FTP cycle by 86.78 and 80.87%, respectively, The effect of air-gap between the monoliths has been also examined. It is found that air-gap has a beneficial effect on reducing pressure drop and cold-start emissions.

• 한국소음진동공학회논문집
• /
• 제19권7호
• /
• pp.736-745
• /
• 2009

Fuel cells convert a fuel together with oxygen in a highly efficient electrochemical reaction to electricity and water. Since the electrochemical reaction in the fuel cell stack dose not generate any noise, Fuel cell systems are expected to operated much quieter than combustion engines. However, the tonal noise and the broad band noise caused by a centrifugal compressor and an electric motor cause which is required to feed the ambient air to the cathode of the fuel cell stack with high pressure. In this study, the multi-camber perforated muffler is used to reduce noise. We propose optimized muffler model using an axiomatic design method that optimizes the parameters of perforated muffler while keeping the volume of muffler minimized.

• 전력전자학회논문지
• /
• 제15권2호
• /
• pp.134-141
• /
• 2010

소형 PEM (Proton Exchange Membrane) 연료전지 시스템은 가습이 필요치 않아 상용화의 가능성이 크지만 그 제어 방법은 뚜렷하게 정립되어 있지 않다. 따라서 본 논문에서는 소형 PEM 연료전지 시스템의 제어를 위해 이중 루프 구조의 제어방식을 정립하고 DSP (Digital Signal Processor)를 이용하여 구현한다. 일반적으로 연료전지 시스템에서 제어의 핵심 요소는 크게 공기와 수소의 공급, 스택 내부의 수분 관리, 스택의 온도 관리로 나뉜다. 별도의 가습이 없이 공랭식으로 구동되는 소형 PEM 연료전지 스택의 제어에 있어서 팬은 스택의 공기 공급과 열관리 및 수분관리를 위한 핵심적인 역할을 하며, 퍼지밸브는 스택 내부의 잉여수분을 배출한다. 제안된 방식은 이중 제어루프를 이용한 팬의 제어를 통해 팬의 과도응답을 빠르게 하여 공기의 공급 속도를 개선시키며, 연료전지 스택의 전압변화를 피드백 하여 보상해줌으로써 연료전지가 부하변동에 대해 신속한 응답 특성을 갖도록 하였다. 제안된 방법의 유용함은 60W급 소형 PEM 연료전지 시스템의 실험과 이를 이용한 노트북 컴퓨터의 구동을 통해 검증된다.

• 한국전기전자재료학회논문지
• /
• 제23권12호
• /
• pp.1002-1006
• /
• 2010

In this study, magnesium (Mg), zinc (Zn) and aluminium (Al) as anode electrode and the solution of NaCl dissolved with 2~20 wt% as electrolytes were used for the metal-air cell. The open circuit voltage, short circuit current and I-V characteristics upon different kinds of anode electrode and electrolyte concentration were investigated. The open circuit voltage, initially about 1.45 V, rises to 1.6 V during the first 10 minutes indicating the necessity of an induction time to activate the catalyst on the air cathode. The short circuit current increases with an increased concentration of NaCl, causes an increase in the conductivity of the electrolyte solution, but the open circuit voltage did not under undergo influence of electrolyte. From NaCl 20 wt% electrolyte, the maximum output power of the magnesium electrode materials was measured with 177mW. It is found that the power characteristics of metal-air cell could be improved by using magnesium electrode materials in the NaCl electrolyte.

• 한국수소및신에너지학회논문집
• /
• 제20권2호
• /
• pp.125-132
• /
• 2009

Cylinder shaped air-breathing PEMFC has been developed to have small volume, low contact resistance and better air accessibility to the open cathode. This cylinder shaped design consists of an anode cylinder with helical flow channel and a cathode current collector with slits. The pressure distribution measurement according to the shapes was performed. The test result indicated that cylinder shaped fuel cell has better pressure distribution compared with the planar shaped fuel cell. The better pressure distribution was connected to the higher performance. The maximum power density of cylinder shaped fuel cell was about 20% higher than the planar shaped fuel cell. The maximum power density of the developed cylinder shaped air-breathing PEMFC with dry hydrogen was $220\;mW/cm^2$ and with humidified hydrogen was $293\;mW/cm^2$.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.45-48
• /
• 2008

This paper presents a passive air-breathing direct methanol fuel cell (DMFC) which has been designed and tested. The single cell is fuelled by methanol vapor that is supplied through flow channel from a methanol reservoir at the anode, and the oxygen is supplied via natural air-breathing at the cathode. The methods for supplying the methanol vapor to the single cell were parallel channel and chamber. This research investigates various methods to identify the effects of using flow channels for providing the methanol vapor at the anode, and the opening ratio between the inlet and outlet ports for the methanol flow at the anode. The best flow channel condition for passive DMFC was a chamber, and the opening ratio was 0.8. Under these conditions, the peak power was 10.2mW/$cm^2$ at room temperature and ambient pressure. The key issues for the Passive DMFCs for using methanol vapor are that sufficient methanol needs to be supplied using a large as possible opening ratio. However, it is shown that the performance of the passive DMFC, which has a channel at the anode,is low due to the low differential pressure and insufficient methanol supply rate.

• 한국수소및신에너지학회논문집
• /
• 제19권4호
• /
• pp.283-290
• /
• 2008

In this paper, experiments with an air-breathing proton exchange membrane fuel cell (PEMFC) for mobile devices were carried out according to cathode conditions. These conditions are defined by the cathode flow field plate type (the channel type, the open type) and the cathode surface direction. Single-cell and 6-cell stack were used in the experiments. The experimental results showed that the open-type cathode flow field plate gave a better performance than the small channel type. In the experiments related to the direction of the slits on the cathode flow field plate, the horizontal slit cell was better than the vertical one. With respect to the cathode surface direction, when the cathode surface is placed in the direction normal to the ground, the PEMFC generated more stable power in the mass transport loss region. Since stable power in the mass transport region is closely related to the air supply, computational fluid dynamics (CFD) analysis for air-breathing PEMFC of different cathode surface directions was performed.

• Environmental Engineering Research
• /
• 제23권3호
• /
• pp.258-264
• /
• 2018

The objectives of this research were to 1) isolate and identify thermophilic bacteria for food waste treatment; 2) investigate the capability of food waste treatment using Bacillus species; and 3) develop air-dried Bacillus starters for food waste treatment. Five Bacillus species were isolated from food wastes and identified as Bacillus licheniformis (B. licheniformis) G1, Bacillus circulans C2, Bacillus subtilis (B. subtilis) E1, Bacillus vanillea F1, and Bacillus atrophaeus G2 based on 16S rDNA sequencing. Each identified Bacillus and the mixture of Bacillus species were cultivated in the standard food waste at $45^{\circ}C$ for 8 d. Changes in cell count, solid contents, and pH of the food waste were monitored during cultivation. Air-dried Bacillus cell powders were prepared using wheat flour and lactomil as excipients, and the cell count and survival rate were determined. The cell count of B. licheniformis G1 exhibited the highest number among the tested Bacillus (${\sim}10^8CFU/mL$). The greatest reduction in solid contents of food waste was achieved by B. subtilis E1 (22.6%). The mixture of B. licheniformis G1 and B. subtilis E1 exhibited a synergistic effect on the reduction of solid contents. Lactomil was determined as better excipient than wheat flour based on the greatest survival rate of 95%.

• 한국자동차공학회논문집
• /
• 제16권3호
• /
• pp.87-93
• /
• 2008

The $CO_2$ air conditioning system installed in fuel cell vehicles could be used either for stack cooling or for cabin cooling, and thus was used for the stack cooling when additional stack heat release was required over a fixed radiator capacity for high power generation. This study investigated the performance of the stack cooling system using $CO_2$ air conditioner at various operating conditions. Also, the heat releasing effectiveness and mutual interference were analyzed for the stack cooling system using an air conditioner and compared with the conventional radiator cooling system with/without cabin cooling. The heat release of the stack cooling system with the aid of $CO_2$ air conditioner increased up to 36% more than that of the conventional radiator cooling system with cabin cooling. Furthermore, the heat release of the stack cooling system using $CO_2$ air conditioner increased more by 7% than that of the conventional radiator cooling system without cabin cooling.