• Journal of Environmental Health Sciences
• /
• v.26 no.4
• /
• pp.134-140
• /
• 2000

The increase in traffic is a worldwide phenomenon. In Korea, it has been increased by 20% per annual in recent 1990’s and approximately 10 millions cars had been registered until 1997. This traffic could easily affect and contribute the local outdoor air quality(QAQ) concerned. The QAQ in highway in one of the examples and the subject in this study. The seoul tollgate located at the north-end of Keypngbu Highway was selected for the study. In case of highway tollgate, the local air pollution could be directly affected by the traffic to approach, wait and start the tollgate. Nitrogen dioxide (NO$_2$) concentration exceeded the EAQS(Environmental Air Quality Standards), but overall indoor air quality was a little better than the outdoor air quality. The measured TSP concentration was much higher than that of the EAQS. To apply a management to a air quality problem of Seoul tollgate, it was predicted air quality with traffic volume and weather condition. It was calculated NO$_2$ emission with traffic volume and predicted in and out of booth by CALINE3 at the Seoul tollgate. To make a comparison between measured and predicted concentration, the prediction was good. It was shown that NO$_2$ concentration was high in the morning at the from Seoul direction and in the evening at the to Seoul direction. it was thought that NO$_2$ concentration variation was reflected according to the traffic volume.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.29 no.6
• /
• pp.27-36
• /
• 2002

The objective of this study is to improve the quality of the atmospheric environment by incorporating the factors of meteorology and urban climate into the field of urban and environmental planning. To this end, we have conducted a study on CLIMATOP and the mapping of urban climate, which are basic data used to analyze changes in climatic factors and the stagnation and accumulation of air pollutants. In particular, we focused on understanding the formation and movement of cold fresh air and its influx into urban areas by measuring and analyzing climatic factors. As a study result, classification criteria far CLIMATOP and a urban climatic map were made. In addition, we analyzed a digital elevation model, climatic data, and isothermal curves. As a result, we identified the corridor through which cold fresh air moves. We also observed that the temperature of the fluxed cold fresh air increased as land use changed. When the results of this study are applied to urban re-development and re-building projects, which require preliminary environmental assessment and environmental impact assessment, the practice proposed by this study is expected to contribute to the natural purification of air pollution activating the movement of cold fresh air and its influx into urban areas.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.27 no.3
• /
• pp.128-136
• /
• 2015

Reducing the building energy consumption has become one of the most important issues. However, the current engineering and technological involvement in energy analysis has been relatively low in the existing buildings. In the existing buildings, end-use analysis must be accompanied to calculate the exact amount in energy savings and such analysis should be conducted based on the energy billing data or measurement data by calibration process. Mostly, detailed energy simulation programs have been proposed for the analysis but, it is difficult to utilize them due to realistic problems. In this paper, we developed an end-use analysis tool that have input function for energy audit data and two case studies were conducted in the real-life office buildings located in Seoul, Korea. Mean Bias Error (MBE) and Coefficient of Variation of Root-Mean- Squreaed-Error (CV(RMSE)) are used for the criteria of comparison. Each index was calculated by using monthly utility bills of electricity and gas consumption. Results showed that MBE and CV (RMSE) represented with acceptable values of -0.1% and 5.7% respectively.

• Journal of Advanced Navigation Technology
• /
• v.11 no.2
• /
• pp.163-169
• /
• 2007

In this paper, we propose a method of trigger pulse generation to capture the image on time by making a synchronization between the x-ray generator and digital x-ray image acquisition system. we designed a wireless trigger pulse generation circuit to make a synchronization between x-ray generator and digital image acquisition system and analysis its performance. When it starts to detect a certain level of x-ray radiation or above from the air, this method starts to generate a ACQ_START signal to indicate the timing for image acquisition starting from digital image acquisition system. Hence, when it starts to detect under certain level of x-ray signal from the air, this method starts to generate a ACC_END signal to indicate the timing for image acquisition stop from digital image acquisition system. Image acquisition is activated only this time between ACQ_START and ACQ_END signal. By doing this wireless detecting of x-ray signal from remote, we can get more accurate timing for capturing the x-ray image and any type of x-ray generator can be connected to digital image acquisition system, regards of wired protocol. This makes easy installation. We could get 3.5 line pair / mm resolution at 20 mAs of x-ray level with resolution chart. This is same or better image comparing to conventional wired result.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.34 no.7
• /
• pp.43-52
• /
• 2018

In this study, annual site and primary energy use intensities (EUIs) and CO2 emission intensities (CEIs) per area by end use were estimated based on the measurement data from June 2016 to May 2017 of 50 sample apartment units in Seoul. In addition, estimated site EUIs by end use were compared to the U.S. Residential Energy Consumption Survey (RECS) 2009 data. Site EUIs by end use were found to be in the order of heating > electric appliance > domestic hot water > cooking > lighting > cooling > air movement. In the case of primary EUIs and CEIs by end use, electric appliance was found to be the largest. As results of comparison with the RECS 2009 data, it was found that site EUIs were very similar for heating, domestic hot water and electric appliance, etc., but slightly different for cooling. The number of sample apartment units will continue to increase until 2020 (total number of samples 200) and intensities data by end use will be continuously updated through continuous collection of measurement data.

• Journal of the Korean Society of Tobacco Science
• /
• v.27 no.2
• /
• pp.201-206
• /
• 2005

In this work, we studied the effects of the moisture contents of cut tobacco on loose end of cigarettes. The loose end of the cigarette groups decreased with the increase of moisture contents of the cut tobacco and especially the loose end of A and C groups decreased to $31\%\;and\;52\%$ with the increase of $1\%$ moisture contents. $A-13.5\%\;and\;B-14.0\%\;and\; C-14.0\%$ moisture samples showed the increase of the weight ratio of cut tobacco over 1.4mm cut length but the decrease under 1.4mm cut length. We concluded that the main reasons were regarded to reduction of small fragment tobaccos caused by increase of moisture contents and exception of air-suction transport of tobaccos to cigarette making machine. In spite of the moisture increase of cut tobaccos under fixed EPD(encapsulated pressure drop), the hardness of Band C sample groups were maintained constantly except A group. This result means that under fixed EPD, the weight of cut tobacco in cigarette rods increases to compensate the reduction of pressure drop by moisture increase of cut tobaccos.

• 대한공업교육학회지
• /
• v.31 no.2
• /
• pp.350-363
• /
• 2006

Recently, the micro end-milling processing is demanded the high-precise technique with good surface roughness and rapid time in milli-structure parts, micro machine parts and molding industry. The cutting conditions of micro end-milling has an effect on surface roughness of cutting surface. Therefore this study was carried out to cut stainless steel using high revolution air bearing spindle and micro end-mill and analyze the cutting condition to get the optimum surface roughness by design of experiment. From this study, surface roughness have an much effect according to priority on depth of cut, revolution of spindle and feed.

• The Journal of the Korea Contents Association
• /
• v.15 no.1
• /
• pp.1-8
• /
• 2015

The purpose of this research is to identify the start and end point of TV program on Web TV. Until now, to replace realtime TV advertisement with Web TV advertisement, human work was the only way. To automatize the process, knowing the start and end point of TV program is the core technology. In this study, I extract 'Black level' between TV program and regard it as start & end point of program. The result of this study is showing that extracting 'Black level' can be a useful tool to define start & end point of TV program. And it will be also use an automatize replacement system for Web TV advertisement.

• IE interfaces
• /
• v.20 no.3
• /
• pp.298-308
• /
• 2007

Radio Frequency Identification (RFID) is one of Identification Technologies today. Many of the large retailers in the United States and Europe have established requirements for their suppliers to use RFID technology in 2004. Recently Airbus and Boeing have announced plans to develop a single RFID specification to be used by both companies to use RFID tags to identify commercial aircraft parts. However, it does not mean the end of barcode and it may take several years before the wide adoption of the RFID. This is because a precise business process reengineering is required with technology itself to get the potential benefits of RFID. In this paper, we introduce an RFID enabled air baggage handling process which has been developed and tested recently. We believe our study would give a good guideline for further researches on RFID application in the aviation industry.

• Fashion & Textile Research Journal
• /
• v.7 no.1
• /
• pp.101-105
• /
• 2005

This study surveys the warp and weft tension differences between projectile and air-jet looms and analyses the mechanical properties of worsted fabrics for garment with relation of these loom characteristics using KES-FB system. The paper is divided by two parts. In the 1st paper, the worsted fabric is woven as 5 harness satin weave using 1/40 Nm sirofil worsted warp yarn and 1/30 Nm worsted weft yarn by projectile(Sulzer) and air-jet looms(Picanol PAT and OMNI), respectively. The weavability is also analysed by measuring warp tension variation according to the warp position and weft tension of 3 kinds of looms. The relationship between shed amount and the warp tension is surveyed, and the relationship between end breaks and warp and weft tensions is also discussed.