• 열처리공학회지
• /
• 제4권2호
• /
• pp.47-53
• /
• 1991

Recrystallization behaviors of ordered and disordered structures in $Ll_2$ type $Ni_3Fe$ alloy were studied through hardness measurement and differential thermal analysis. When the disordered structure was isothermally aged at $480^{\circ}C$ below order-disorder transition temperature, the hardness of the structure was increased due to progressive ordering with increasing aging time. The hardness of the disordered structure was increased rapidly with increasing deformation degree up to 10%, and then gradually increased with further deformation degree. while the hardness of the ordered structure was increased rapidly with increasing deformation degree up to 10%, showing a constant hardness value up to 50% and gradually decreased with further deformation degree. The hardness of the ordered structure was higher than that of the disordered structure at all same deformation degrees. The recrystallization temperature of the ordered and disordered structures were decreased with increasing deformation degree. At the same deformation degrees, the recrystallization temperature of the ordered structure was lower than that of the desordered structure.

• 열처리공학회지
• /
• 제34권6호
• /
• pp.302-308
• /
• 2021

The aim of this study was to investigate the dependence of the hardness and thermal conductivity on the volume fraction of discontinuous precipitates (DPs) in the Mg-9.3%Al alloy with (α-(Mg)+DPs) dual phase structure. In order to obtain various DPs volume fractions, the alloy was solution-treated at 688 K for 24 h and then aged at 418 K for up to 144 h. The volume fraction of DPs increased from 0% to 63% with an increase in the aging time up to 72 h, over which, continuous precipitation was observed within the α-(Mg) grains. It is noticeable that the hardness and thermal conductivity of the alloy increased linearly with the volume fraction of DPs. The improved hardness and thermal conductivity with respect to volume fraction of DPs are closely associated with the higher hardness of the DPs with fine (α+β) lamellar structure and the lower Al concentration in the α phase layer of the DPs, respectively.

• 한국재료학회지
• /
• 제26권7호
• /
• pp.388-392
• /
• 2016

A cold roll-bonding process was applied to fabricate an AA1050/AA6061/AA1050 laminate complex sheet. Two AA1050 and one AA6061 sheets of 2 mm thickness, 40 mm width and 300 mm length were stacked up after surface treatment that included degreasing and wire brushing; material was then reduced to a thickness of 3 mm by one-pass cold rolling. The laminate sheet bonded by the rolling was further reduced to 1.2 mm in thickness by conventional rolling. The rolling was performed at ambient temperature without lubricant using a 2-high mill with a roll diameter of 210 mm. The rolling speed was 5.0 m/sec. The AA1050/AA6061/AA1050 laminate complex sheet fabricated by roll bonding was then hardened by natural aging T4) and artificial aging (T6) treatments. The microstructures of the as-roll bonded and the age hardened Al complex sheets were revealed by optical microscope observation; the mechanical properties were investigated by tensile testing and hardness testing. The strength of the as-roll bonded complex sheet was found to increase by 2.9 times compared to that value of the starting material. In addition, the hardness of the complex sheets increased with cold rolling for AA1050 and age-hardening treatment for AA6061, respectively. After heat treatment, both AA1050 and AA6061 showed typical recrystallization structures in which the grains were equiaxed; however, the grain size was smaller in AA6061 than in AA1050.

• Journal of Welding and Joining
• /
• 제5권2호
• /
• pp.53-59
• /
• 1987

The effect of applied stress, current density and heat-treatment after welding on the time to fracture, fracture behavior was investigated by the method of constant load tensile testing under catholic charging with hydrogen in E.B. welded 250,300 Grade 18% Ni Maraging steel sheet. The main results obtained are as follows: 1. All specimen showed the characteristic delayed failure and the time to fracture showed decreasing tendency with the increase in current density and applied stress. 2. Hydrogen embitterment susceptibility of notched specimen after solution-treatment and aging after welding was more increased than that of aged smooth specimen and as welded specimen. 3. Fracture surface showed a typical intergranular fracture on the border, a dimple pattern in the center of specimen and some quasi-cleavage fracture between the intergranular and the dimple.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.295-298
• /
• 2003

High temperature deformation behavior of a Ti-Al intermetallic compound has been investigated. Specimens with a near gamma and a lamella structures were obtained by performing heat treatment at 1200 and 1330$^{\circ}C$, respectively, for 24 hr and stabilized at 900$^{\circ}C$ for 4 hr followed by air cooling. A series of load relaxation tests has been conducted on these samples at temperatures ranging from 850 to 950$^{\circ}C$ to construct flow curves in the strain rate range from 10$\^$-6//s to 10$\^$-3//s. Strain hardening was observed even at the temperature of 950$^{\circ}C$ in both the near gamma and the lamella structures. Further aging treatment for 12 hr at test temperatures has found to cause no softening in both microstructures.

• Journal of Welding and Joining
• /
• 제22권1호
• /
• pp.43-49
• /
• 2004

Contact tip is located so near to welding arc that it is heated to high temperature during long time welding. In such a situation, tip changes in its microstructure and in turn its mechanical properties. This study was intended to investigate those changes by using simulated heat treatment. As a result of this study, it was confirmed that tip of Cu-P alloy hardened with severe cold deformation lose its initial hardness to a large extent within 60 min due to the occurrence of rapid recrystallization while that of Cu-Cr composition hardened by proper aging treatment can preserve its intial hardness for about 1,000 min or longer. Based on these results, suggested was a guideline that can classify contact tips into two different grades: deformation-hardened type and precipitation-hardened type. Following a guideline, a tip with Cu-Cr composition can be classified into the deformation-hardened type if it is in the over-aged condition. Such a guideline is well described.

• Nutrition Research and Practice
• /
• 제8권5호
• /
• pp.526-532
• /
• 2014

BACKGROUND/OBJECTIVES: Acanthopanax sessiliflorus is a native Korean plant and used as a traditional medicine or an ingredient in many Korean foods. The free radical theory of aging suggests that cellular oxidative stress caused by free radicals is the main cause of aging. Free radicals can be removed by cellular anti-oxidants. MATERIALS/METHODS: Here, we examined the anti-oxidant activity of Acanthopanax sessiliflorus extract both in vitro and in vivo. Survival of nematode C. elegans under stress conditions was also compared between control and Acanthopanax sessiliflorus extract-treated groups. Then, anti-aging effect of Acanthopanax sessiliflorus extract was monitored in C. elegans. RESULTS: Stem extract significantly reduced oxidative DNA damage in lymphocyte, which was not observed by leaves or root extract. Survival of C. elegans under oxidative-stress conditions was significantly enhanced by Acanthopanax sessiliflorus stem extract. In addition, Acanthopanax sessiliflorus stem increased resistance to other environmental stresses, including heat shock and ultraviolet irradiation. Treatment with Acanthopanax sessiliflorus stem extract significantly extended both mean and maximum lifespan in C. elegans. However, fertility was not affected by Acanthopanax sessiliflorus stem. CONCLUSION: Different parts of Acanthopanax sessiliflorus have different bioactivities and stem extract have strong anti-oxidant activity in both rat lymphocytes and C. elegans, and conferred a longevity phenotype without reduced reproduction in C. elegans, which provides conclusive evidence to support the free radical theory of aging.

• 비파괴검사학회지
• /
• 제22권2호
• /
• pp.149-154
• /
• 2002

실제 사용 온도 보다 높은 $630^{\circ}C$에서 열처리 시간을 변수로 하여 최대 1000 시간 동안 등온 열처리를 통해 2.25Cr-1Mo 강의 경년열화재를 제작하고 열화에 따른 미세조직과 기계적 특성 변화에 대한 초음파 비파괴평가 법으로 표면 특성평가에 우수한 표면 SH파를 적용하였다. 열화에 따른 초음파의 감쇠와 전파시간 및 웨이블렛을 이용한 음속과 감쇠계수의 주파수 의존성평가를 수행한 결과 열화가 진행됨에 따라서 탄화물은 점차 조대화되고 경도는 감소하였다. 감쇠계수는 열화시간이 증가함에 따라서 증가하였고 전파시간 역시 열화의 초기단계에 급격히 증가했다. 초음파의 감쇠와 경도와는 좋은 상관관계를 나타내어 감쇠계수는 경년열화 평가에 중요한 파라미터임을 알 수 있었다.

• 한국주조공학회지
• /
• 제38권4호
• /
• pp.75-81
• /
• 2018

This study examined the effect of the CaMgSn ternary phase on the aging response of the Mg-Sn-Zn alloy. The results revealed that the CaMgSn ternary phase formed in rod-like or needle-like shapes in Mg-3Zn-0.3Ca-xSn (x=1.5, 3, and 5 wt%) alloys and its size decreased as the Sn content increased from 1.5 wt% to 5 wt%. The Mg-3Zn-0.3Ca-5Sn alloy with a relatively fine CaMgSn phase was subjected to solution heat treatment and an aging process. Both the Mg-5Sn-3Zn-0.3Ca and Mg-5Sn-3Zn (base alloy) alloys had similar peak hardness values throughout all aging temperatures but the time-to-peak hardness in the Mg-5Sn-3Zn-0.3Ca alloy was 24-36 hours-earlier than that in the base alloy. Precipitates in the Mg-5Sn-3Zn-0.3Ca alloy were more refined than those in the Mg-5Sn-3Zn alloy and were mostly formed on basal planes. The $Mg_2Sn$ phase formed in either plate-like or rod-like shapes in the Mg-5Sn-3Zn alloy, whereas block-shaped $Mg_2Sn$ particles also formed in the Mg-5Sn-3Zn-0.3Ca alloy.

• 한국식품영양과학회지
• /
• 제35권5호
• /
• pp.594-599
• /
• 2006

이전의 연구에서, 우육중의 주된 알레르겐은 우육추출물 중의 BSA, BGG라고 보고하였다. 본 연구에서는 이들 단백질의 열처리와 초고압처리와 같은 물리적 처리에 따른 SDS-PAGE상의 변화와 우육알레르기 환자의 혈청을 이용한 알레르겐성의 변화를 Western blots로 관찰하였다. 우육추출물에 대한 열처리에 의한 알레르겐 단백질의 변화에서, $100^{\circ}C$ 가열처리군에서 BSA band는 큰 감소를 보였으나, BGG band는 완전히 제거되지 못하고 남아 있었고, 항원성 역시 대조군에 비하여 감소는 하였으나 여전히 유지되고 있었다. $120^{\circ}C$이상의 열처리는 추출물중의 BSA와 BGG band 의 소실과 이에 따른 항원성의 큰 감소를 가져왔다. 우육추출물중의 BSA단백질은 열처리에서와 달리 초고압처리에 의하여 전기영동상에 거의 변화를 보이지 않았다. 그러나 BGG 단백질은 400 MPa 가압처리군부터 전기 영동상 band가 감소하였고, 항원성 역시 유의적으로 감소하였다. 이는 초고압처리 정도에 따른 우육추출물중의 BSA와 BGG를 포함한 여러 분자의 SDS-PAGE상의 특이적 변화가 최초로 시사된 결과이다. 이러한 BGG 단백질의 고압처리에 의한 변화는 추출물중의 어떤 효소에 의한 것으로 추측되었고, 고압처리 후 $37^{\circ}C$숙성 실험으로 이러한 가설이 확인되었다. 우육추출물에 존재하고 초고압처리로 활성화되어 BGG분자에 특이적으로 관여하는 효소 및 이와 관련된 메커니즘에 대한 연구가 앞으로 필요할 것으로 보인다.