• Journal of Welding and Joining
• /
• 제26권5호
• /
• pp.60-65
• /
• 2008

Ferritic stainless steels of the 400 series have been available for automotive exhaust system, heat exchanger, radiater etc. in various industrial because heat resistance, corrosion resistance and strength are excellent. Especially, automotive exhaust system is required good heat resistance because typical temperature of exhaust system exposed during operation of engine is reach up to $800^{\circ}C$. However, research for effect of high temperature in ferritic stainless steels is not enough. In this study, high temperature tensile properties of lap weld of ferritic stainless steels(STS 429) were investigated. In accordance with heat input, lap welds had been produced and were evaluated at high temperature($800^{\circ}C$) to compare high temperature tensile properties. In addition, room temperature tensile tests were carried out for non-aging and aging specimens. As a result of R.T tensile test, non-aging specimens were fractured in base metal except for low heat input specimen and aging specimens were fractured in weld metal. Also high temperature tensile test were carried out by aging specimen. After high temperature tensile test, fracture of aged specimen was occurred in base metal except for low heat input specimen. Fracture surface of low heat input specimen in weld metal was confirmed as brittle fracture with observation using scanning electron microscope(SEM). Significant decrease in ultimate tensile strength (between 82 and 85%) was observed for aged ferritic stainless steels(STS 429) when tested at high temperature.

• 대한금속재료학회지
• /
• 제48권10호
• /
• pp.957-963
• /
• 2010

The aging behavior of aluminum borate whisker ($Al_{18}B_4O_{33}$) reinforced AS52+Sr magnesium matrix composites was investigated with Vickers hardness measurements, bending tests, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Experimental results showed that aging is accelerated in the $AS52+Sr/Al_{18}B_4O_{33}$ composite compared with an unreinforced AS52+Sr alloy. The hardness of the alloy and composite increases monotonically as a function of the aging time before reaching its peak hardness and then gradually decreases. The composite reaches its peak hardness in 10 h, whereas the matrix alloy requires 30h, indicating accelerated age-hardening in the $AS52+Sr/Al_{18}B_4O_{33}$ composite compared with the unreinforced AS52+Sr alloy at $170^{\circ}C$. The interfacial reaction of $AS52+Sr/Al_{18}B_4O_{33}$ magnesium matrix composite is considered to play a dominant role in the strengthening mechanism, ultimately affecting the mechanical properties of the composite.

• 한국전기전자재료학회논문지
• /
• 제32권1호
• /
• pp.6-12
• /
• 2019

Bonding properties of epoxy-containing solder joints were investigated by a high temperature aging test. Specimens were prepared by bonding an R3216 standard chip resistor to an OSP-finished PCB by a reflow process with two basic types of solder (SAC305 & Sn58Bi) pastes and two epoxy-solder (SAC305+epoxy & Sn58Bi+epoxy) pastes. In all epoxy solder joints, an epoxy fillet was formed in the hardened epoxy, lying around the outer edge of the solder joint, between the chip and the Cu pad. In order to analyze the bonding characteristics of solder joints at high temperatures, a high-temperature aging test at $150^{\circ}C$ was carried out for 14 days (336 h). After aging, the intermetallic compound $Cu_6Sn_5$ was found to have formed in the solder joint on the Cu pad, and the shear stress on the conventional solder joint was reduced by a significant amount. The reason that the shear force did not decrease much, even though in epoxy solder, was thatbecause epoxy hardened at the outer edge of the supported solder joints. Using epoxy solder, strong bonding behavior can be ensured due to this resistance to shear force, even in metallurgical changes such as those where intermetallic compounds form at solder joints.

• 대한금속재료학회지
• /
• 제47권3호
• /
• pp.175-181
• /
• 2009

Mechanical properties and precipitation behavior of backward extruded 6061 Al alloy for pressure vessel were investigated using tensile test, transmission electron microscopy (TEM) and differential scanning calorimeter (DSC). In this study, solution heat treatment (SHT) was performed at $535^{\circ}C$ for 30~90 min and aging treatment was conducted at 177 and $190^{\circ}C$ for 1~7 h. Maximum tensile strength of $36.6kgf/mm^2$ and yield strength of $33.29kgf/mm^2$ were achieved at the aging time of 5 h at $190^{\circ}C$. TEM observation showed that fine needle-like ${\beta}^{{\prime}{\prime}}$ phase which has 35~45 nm of length was uniformly distributed in the aged 6061 Al alloy specimen. From tensile test, TEM and DSC analysis, it is expected that aging time of 2~5 h at $190^{\circ}C$ is suitable for the extruded A6061 used as pressure vessels.

• Preventive Nutrition and Food Science
• /
• 제18권1호
• /
• pp.50-59
• /
• 2013

Black jujube was made by aging dried jujube and its physiochemical characteristics, antioxidant activities and ${\alpha}$-glucosidase inhibitory activities were evaluated. The moisture and sugar contents were increased depending on the period of aging times and the pH was reduced thereby increasing acidity. The color of black jujube extract was changed from red to black resulting in decreases of Hunter color values L, a and b. As the aging progressed, sucrose was decomposed by increasing glucose and fructose, indicating higher contents of the total reducing sugars. Among the six different types of organic acids extracted from dried jujube, the levels of oxalic acid and citric acid were increased as the aging progressed. The total polyphenol contents in ethanol and water extracts of dried jujube were 7.74 and 8.12 mg/g, respectively. The water extract of black jujube aged for 48 hr contained the highest polyphenol contents at 16.82 mg/g. The 5'-hydroxymethylfurfural (5'-HMF) contents of black jujube extract significantly increased by longer aging times, and contained higher contents in the ethanol extract than water extract. The ethanol extract of black jujube showed the highest 5'-HMF content with 338.89 mg% after aging for 3 days. Also, $IC_{50}$ values of black jujube aged for 72 hr evaluated by DPPH and ABTS radical assays were 0.54 and 0.59 mg/mL, respectively. ${\alpha}$-Glucosidase inhibitory activities of black jujube at the concentration of 3.33 mg/mL (ethanol extract) increased from 65 to 80 % after aging for 72 hr.

• 한국추진공학회지
• /
• 제23권3호
• /
• pp.51-57
• /
• 2019

HTPB 고체 추진제 기계적 물성의 후경화 효과에 대하여 시편 시험을 통하여 평가하였다. 후경화 반응 완료 후 시편 가속노화 시험을 실시하여 Arrhenius 식의 계수를 획득하였다. 확인을 위하여 원통형 모사 충전체를 설계, 제작하여 가속노화 시험을 수행하였으며, 시험 후 추진제 표면 부위, 중앙 부위, 접착 부위에 대하여 시편을 채취하여 노화 물성을 평가하였다. 측정된 결과에 대하여, 획득된 가속노화 식으로 예측하여 비교하였다. 그 결과 JANNAF 시편 시험을 통한 가속노화 식은 추진제 재료의 노화를 잘 예측하였으나 접착 부위에서는 실제 측정 결과와 차이를 나타내었다. 따라서 실기형 추진기관에서 노화 시료를 채취하는 경우 시험 목적에 부합하도록 시편 채취 부위를 선정해야 한다.

• 펄프종이기술
• /
• 제48권3호
• /
• pp.80-90
• /
• 2016

The purpose of this study was to investigate the functional properties of natural dyed Hanji for cultural properties conservation and storage. To estimate functional properties of Hanji, antimicrobial, insect repellent test, and Oddy test were executed. Hanji dyed with 10% Golden thread (Coptis chinensis), a natural dye and silver nitrate mordanting showed the most excellent antifungal activities against A. niger, P. chrysogenum, and Trichoderma sp. before and after aging. The insects repellent test followed didn't indicate significant effects on treated Hanji against Lasioderma serricorne, Sitophilus zeamais, and Tribolium castaneum. According to Oddy test result, Hanji dyed with Golden thread and silver nitrate caused no significant corrosions on copper, silver, and lead after aging 28 days.

• 한국전기전자재료학회논문지
• /
• 제26권9호
• /
• pp.662-668
• /
• 2013

Reported here are results of the mechanical and electrical properties of both of intact and thermally degraded epoxy-coated copper busducts that are made by fluidized bed process. To elucidate and compare the properties mentioned above, electrical breakdown by thermal and water aging, v-t characteristic, bending test, impact test and cross cut test are carried out. Although the performance of electrical and mechanical properties are gradually decreased in increasing the severe conditions such as temperature, aging time, and so forth, sample C has a better performance in both mechanical and electrical properties.

• Elastomers and Composites
• /
• 제52권2호
• /
• pp.105-113
• /
• 2017

The curing behavior, mechanical properties, hot-air aging resistance, abrasion properties,thermal properties, etc., of EVM/EPM/APP (ammonium polyphosphate)/DPER (dipentaerythritol)/EG (expandable graphite) and EVM/EPM/ATH (aluminium trihydroxide) flame retarding systems in ethylene vinyl acetate rubber (EVM) blends with EPM (ethylene propylene rubber) were sequentially examined. For both flame retarding systems, the torque values increased with the content of EPM rubber and with the vulcanization time. As the content of EPM rubber increased, the scorch time became shorter, whereas the optimum cure time followed an increasing trend. For the EVM/EPM/APP/DPER/EG flameretarding system, as the content of EPM rubber increased, the hardness did not change,whereas the tensile strength and elongation at break decreased. A hot-air aging resistance test at $150^{\circ}C$ showed that the heat resistance decreased with the EPM content regardless of the kinds and contents of flame retardants. As the EPM content increased, the abrasion rate became higher and the abrasion resistance of the EVM/EPM/APP/DPER/EG flame retarding systems exceeded that of the EVM/EPM/ATH flame retarding counterparts. In comparison with the EVM/EPM/ATH flame retarding systems, the thermal stability of the EVM/EPM/APP/DPER/EG flame retarding system showed an increasing tendency.

• Transactions on Electrical and Electronic Materials
• /
• 제8권6호
• /
• pp.234-240
• /
• 2007

The electrical properties and dc aging behavior for specified stress state of system, which is composed of quaternary Zn-Pr-Co-Cr, were investigated for different $Dy_2O_3$ addition doping level. As $Dy_2O_3$ doping level increased, the density decreased in the range of 5.51-4.90 $g/cm^3$, reaching maximum at 0.5 mol% and the average ZnO grain size decreased in the range of 17.7-6.0 ${\mu}m$. The incorporation of $Dy_2O_3$ significantly improved the non-ohmic properties, above 30 in non-ohmic coefficient, compared with that of undoped samples. The samples with the best performance of non-ohmic properties were obtained for $Dy_2O_3$ doping level of 1.0 mol%, with 49 in non-ohmic coefficient and 2.6 ${\mu}A/cm^2$ in leakage current. The samples with the highest stability were obtained for $Dy_2O_3$ doping level of 0.5 mol%.