• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.295-298
• /
• 2003

High temperature deformation behavior of a Ti-Al intermetallic compound has been investigated. Specimens with a near gamma and a lamella structures were obtained by performing heat treatment at 1200 and 1330$^{\circ}C$, respectively, for 24 hr and stabilized at 900$^{\circ}C$ for 4 hr followed by air cooling. A series of load relaxation tests has been conducted on these samples at temperatures ranging from 850 to 950$^{\circ}C$ to construct flow curves in the strain rate range from 10$\^$-6//s to 10$\^$-3//s. Strain hardening was observed even at the temperature of 950$^{\circ}C$ in both the near gamma and the lamella structures. Further aging treatment for 12 hr at test temperatures has found to cause no softening in both microstructures.

• 한국전산구조공학회논문집
• /
• 제24권4호
• /
• pp.391-398
• /
• 2011

철근콘크리트 구조물은 타설 후 시간이 경과함에 따라 물리적인 요인과 화학적인 요인으로 인하여 열화가 진행된다. 열화된 구조물의 효율적인 구조해석을 수행하기 위하여 구조물의 거동과 밀접한 관련이 있는 중요열화변수를 정의하는 것은 필요하다. 본 연구에서는 경년열화된 철근콘크리트 전단벽의 중요변수를 분석하기 위하여 일계이차모멘트법을 이용하여 민감도해석을 수행하였다. 콘크리트의 경화현상을 고려하지 않을 경우 구조물의 열화성능이 과소평가될 수 있으므로 콘크리트의 경화에 따른 해석변수들의 민감도를 분석하였다. 열화된 전단벽에서 변수의 중요도는 토네이도 다이어그램으로 나타내었다.

• 콘크리트학회논문집
• /
• 제24권2호
• /
• pp.195-204
• /
• 2012

신구 콘크리트 접합부에서는 굽힌 후 편 철근을 이용한 이음이 발생한다. 철근의 굽힘과 펴는 과정에는 필연적으로 소성 변형이 발생하며, 이 과정에서 가공 경화, 바우싱거 효과, 시효 경화 현상이 발생된다. 이 연구에서는 강종, 지름, 굽힘 내면 반지름, 굽힌 후 펴기까지의 존치기간을 변수로 굽힌 후 편 철근의 인장에 대한 기계적 성질을 조사하였다. 연구 결과, 굽힌 후 편 철근은 비례한계점이 낮아지는 비선형성이 직선 철근에 비해 일찍 발생되었으며, 항복마루 없이 바로 변형경화가 발생하였다. 이것은 굽힘 가공에서 압축을 받은 부분의 바우싱거 효과에 의해 항복점이 낮아졌고, 굽힘 가공에서 인장을 받은 부분의 가공 경화에 의해 항복마루가 없어졌기 때문이다. 높은 강종일수록 항복강도의 저하가 크게 발생되었으며, SD400 철근의 항복강도는 설계기준강도보다 낮았다. 철근은 표면부의 강도가 내부보다 높기 때문에, 높은 강종일수록 굽힌 후 펴면 바우싱거 효과가 크게 발생된다. 굽힌 후 펴기까지의 존치기간이 길면 시효 경화에 의해 항복강도의 상승과 연성의 저하가 발생되었다. Ramberg-Osgood 모델을 기본 형태로 실험 자료를 회귀분석하여 항복강도와 존치기간을 고려한 굽힌 후 편 철근의 응력-변형률 관계를 구성하였다. 이 모델은 굽힌 후 편 철근이 사용된 접합부의 강성 평가에 활용될 수 있다.

• Journal of Magnetics
• /
• 제16권3호
• /
• pp.225-228
• /
• 2011

Magnetic properties and Rockwell hardness of 1Cr-0.5Mo steel have been investigated as a function of isothermal aging time. Our results showed that coercivity, hysteresis loss and Rockwell hardness in the aged samples decreased as aging time increased. This phenomenon was analyzed using optical microscopy and scanning electron microscopy. A significant diffusion of Cr and Mo atoms formed $M_2C$ and $M_7C$ carbides, lowering the matrix strength. $M_2C$ and $M_7C$ carbides partially segregated inside grains, diffused into grain boundaries, and finally resulted in a soft ferrite matrix and a hard grain boundary. The magnetic and mechanical softening of the matrix is likely to govern the properties of the sample more than the hardening of the grain boundary by carbide precipitations.

• 한국추진공학회지
• /
• 제23권3호
• /
• pp.51-57
• /
• 2019

HTPB 고체 추진제 기계적 물성의 후경화 효과에 대하여 시편 시험을 통하여 평가하였다. 후경화 반응 완료 후 시편 가속노화 시험을 실시하여 Arrhenius 식의 계수를 획득하였다. 확인을 위하여 원통형 모사 충전체를 설계, 제작하여 가속노화 시험을 수행하였으며, 시험 후 추진제 표면 부위, 중앙 부위, 접착 부위에 대하여 시편을 채취하여 노화 물성을 평가하였다. 측정된 결과에 대하여, 획득된 가속노화 식으로 예측하여 비교하였다. 그 결과 JANNAF 시편 시험을 통한 가속노화 식은 추진제 재료의 노화를 잘 예측하였으나 접착 부위에서는 실제 측정 결과와 차이를 나타내었다. 따라서 실기형 추진기관에서 노화 시료를 채취하는 경우 시험 목적에 부합하도록 시편 채취 부위를 선정해야 한다.

• 열처리공학회지
• /
• 제4권4호
• /
• pp.24-33
• /
• 1991

The effects of thermomechanical treatments on microstructure and fatigue properties of 7050 Al alloy were investigated. The precipitation kinetics changed to a faster rate due to cold deformation employed in this special TAHA thermomechanical treatments including pre-aging, plastic deformation and two step final-aging. The G.P. zones in the under-aged condition were cut by dislocations and dissolved during the plastic deformation. During the low cycle fatigue, the T6' condition showed cyclic hardening behavior whereas the TMT5, TMT27 and T76 conditions showed cyclic softening at above 0.7% total strain amplitudes. The ${\Delta}K_{th}$ value of TMT27 was improved more than two times, compared with that of T76 condition. The T6' with small shearable precipitates resulted in the markedly high ${\Delta}K_{th}$ value. This is thought to be resulted from dislocation reversibility and roughness-induced crack closure due to planarity of slip.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1996년도 춘계학술발표회논문집(3)
• /
• pp.193-198
• /
• 1996

The effect of dynamic strain aging (DSA) on the leak-before-break (LBB) analysis was estimated through the evaluation of leakage-size-crack and flaw stability in SA106 Gr.C piping steel. Also. the results were represented as a form of "LBB allowable load window". In the DSA temperature region. the leakage-size-crack length was smaller than that at other temperatures and it increased with increasing tensile strain rate. In the results of flaw stability analysis. the lowest instability load appeared at the temperature corresponding to minimum J- R curve which was caused by DSA. The instability load near the plant operating temperature depended on the loading rate of J-R data. and decreased with increasing tensile strain rate. These are due to the strain hardening characteristic and strain rate sensitivity of DSA. In the "LBB allowable load window". LBB allowable region was the narrowest at the temperature and loading conditions where DSA occurs.

• 한국주조공학회지
• /
• 제24권4호
• /
• pp.231-237
• /
• 2004

Bake hardenable steel utilizes the phenomenon of strain aging to provide an increase in the yield strength of formed components. An increase of the carbon content will improve the bake hardening response: more solutes are available to pin mobile dislocations and to form the clusters more rapidly. But aging resistance decrease as increasing solute carbon. In order to under-stand the compatibility between bake hardenability and aging resistance. The optimum solute carbon control methods during manufacture should be determined. In this paper, the effect of continuous heat cycle conditions such as soaking temperature, rapid cooling start temperature, cooling rate on BH(Bake Hardenability), AI(Aging Index), YP-El(Yield Point Elongation) and other mechanical properties have been investigated. and following results were obtained. In the case of soaking temperature, BH increases with higher soaking temperature because of NbC $dissolution(830^{\circ}C)$, Therefore the solute carbon and BH at $850^{\circ}C$ and $870^{\circ}C$ are higher than these at $810^{\circ}C$. But BH at $870^{\circ}C$ is a little lower than that at $850^{\circ}C$ owing to the ferrite grain size. The measurement of amount of dissolution C using IFT(Internal Friction Test) can explain the relation of solute carbon and BH.

• 한국주조공학회지
• /
• 제18권4호
• /
• pp.364-372
• /
• 1998

Effects of Si and Ca additions on the mechanical properties of AM60 based Mg alloys have been investigated. Hardness of the AM60 based Mg alloys reached a maximum value after aging for approximately 33 hours but the amount of hardness increase was negligible. The poor age hardening response of the alloys was due to low Al content, which implies that Al content must be >6 wt.% to observe age hardening effect. The tensile and yield strength increased with increasing Al, Si, and Ca content but elongation decreased with increasing Al and Si content. The best mechanical properties obtained in AM 40-2.5Si-0.2Ca alloy after T4 heat treatment were as follows; tensile strength 193.4 MPa, yield strength 79.2 MPa, and elongation 11.2%. High temperature property obtained from creep test was also improved by introducing $Mg_2Si$ which has high hardness, high melting temperature and low thermal expansion coefficient.

• 한국표면공학회지
• /
• 제42권5호
• /
• pp.246-249
• /
• 2009

Cu-Ti alloys with titanium in the range of 0.5-6.0 wt% were developed to evaluate the effect of the titanium content and heat treatment on microstructure, hardness, and electrical conductivity. The hardness of the Ti-added copper alloys generally increased with the increase in titanium content and hardening was effective up to the 2.5 wt%-Ti addition. Microstructural examination showed that the second phase of $Cu_4Ti$ started to precipitate out from the 3.0 wt% Ti-addition, and the precipitate size and volume fraction increased with further Ti addition. Aging of the present Cu-Ti alloys at $450^{\circ}C$ for 1 h increased the hardness; however, the further aging up to 10 h did not much change the hardness. In the present study, it was inferred that in optimal Ti addition and aging condition Cu-Ti alloy could have the hardness and electrical conductivity values which are comparable to those of commercial Cu-Be alloy.