• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.502-502
• /
• 2007

Current thin film process using memory device fabrication process use expensive processes such as manufacturing of photo mask, coating of photo resist, exposure, development, and etching. However, direct printing technology has the merits about simple and cost effective processes because inks are directly injective without mask. And also, this technology has the advantage about fabrication of fine pattern line on various substrates such as PCB, FCPB, glass, polymer and so on. In this work, we have fabricated the fine and thick metal pattern line for the electronic circuit board using metal ink contains Ag nano-particles. Metal lines are fabricated by two types of printing methods. One is a conventional printing method which is able to quick fabrication of fine pattern line, but has various difficulties about thick and high resolution DPI(Dot per Inch) pattern lines because of bulge and piling up phenomenon. Another(Second) methods is sequential printing method which has a various merits of fabrication for fine, thick and high resolution pattern lines without bulge. In this work, conductivities of metal pattern line are investigated with respect to printing methods and pattern thickness. As a result, conductivity of thick pattern is about several un.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1336_1337
• /
• 2009

본 논문에서는 유기 박막 트랜지스터의 전극을 잉크젯 프린팅과 스크린 프린팅 방법을 이용하여 유기 박막 트랜지스터를 제작하였다. 전극으로 PEDOT:PSS와 Ag 잉크를 사용하였고, 게이트 절연막으로 polymethyl methacrylate (PMMA)와 poly(4-vinylphenol) (PVP)를 사용하였다. 유기물 활성층으로 pentacene을 진공 증착하였다. 잉크젯 프린팅 방법을 이용하여 제작한 유기 박막 트랜지스터는 전계이동도 (${\mu}_{FET}$) $0.068\;cm^2$/Vs, 문턱전압 ($V_{th}$) -15 V, 전류 점멸비 ($I_{on}/I_{off}$ current ratio) >$10^4$의 전기적 특성을 보였고, 스크린 인쇄 방법을 이용하여 제작한 유기 박막 트랜지스터는 전계이동도 (${\mu}_{FET}$) $0.016\;cm^2$/Vs, 문턱전압 ($V_{th}$) 6 V, 전류 점멸비 ($I_{on}/I_{off}$ current ratio) >$10^4$의 전기적 특성을 보였다. 이를 통하여 프린팅 방법을 이용한 유기 박막 트랜지스터 단일 소자 및 유기 전자 회로 제작의 가능성을 확인 하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.704-704
• /
• 2013

CIGS 박막 태양전지는 I-III-VI족 화합물 반도체로서 직접천이형 에너지 밴드 구조를 가지고 있고, $1{\times}10$ cm의 높은 흡수계수를 가지고 있으며, Ga, Ag, Al을 첨가함으로써 밴드갭을 1~2.7 eV 넓은 범위로 조절가능하다. 본 연구의 목적은 Sputtering 방식과 Cracker cell을 이용한 실험으로 보다 효율적인 방식으로 CIGS 전구체 조성별 특성에 따른 구조와 전기적, 광학적 특성의 효과에 대하여 조사하였다. Cu-In-Ga 전구체는 CuGa(80-20 at.%)과 In(99.0%) target을 사용하여, Sputtering 공정으로 증착하였으며, Cracker cell이 부착된 RTP (rapid thermal processing)를 통하여 셀렌화를 진행하였다. Reservoir zone 온도는 320도, Cracking zone 온도는 900도로 유지하였으며, 진공상태에서 Se이 공급되면서 열처리가 진행되었다.Cu-In-Ga 전구체 구조에서 In의 증착시간을 변화시켜 CIGS 박막에 미치는 영향에 대해 분석하였다. 이때 기판온도는 $500^{\circ}C$로 고정하거나, $240^{\circ}C$ 열처리 후 $500^{\circ}C$에서 열처리하는 두가지를 적용하여 그 영향을 분석하였다. 또한 Selenium이 Cracking zone 온도와 열처리 시간에 따라 미치는 영향의 변화를 조사하였다. 이에 따른 CIGS 박막의 전기적 특성의 변화를 조사하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.4
• /
• pp.373-378
• /
• 2006

We report on plasma damage free-sputtering technologies for organic light emitting diodes (OLEDs), organic thin film transistor (OTFT) and flexible displays by using a box cathode sputtering (BCS) method. Specially designed BCS system has two facing targets generating high magnetic fields ideally entering and leaving the targets, perpendicularly. This target geometry allows the formation of high-density plasma between targets and enables us to realize plasma damage free sputtering on organic layer without protection layer against plasma. The OLED with Al cathode prepared by BCS shows electrical and optical characteristics comparable to OLED with thermally evaporated Mg-Ag cathode. It was found that OLED with Al cathode layer prepared by BCS has much lower leakage current density ($1{\times}10^{-5}\;mA/cm^2$ at -6 V) than that $(1{\times}10^{-2}{\sim}-10^0\;mA/cm^2)$ of OLED prepared by conventional DC sputtering system. This indicates that BCS technique is a promising electrode deposition method for substituting conventional thermal evaporation and DC/RF sputtering in fabrication process of organic based optoelectronics.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.12
• /
• pp.1063-1068
• /
• 2000

Water treeing in underground distribution power cable is not easy to observe by nondestructive method and it has very complex patterns. This study describes the principles and practices of a continuous observation of initiation and growth of tree in polymeric insulation material using an image measurement technique. Using this technique we could observe water tree and the growing process of electrical tree due to the water tree and the growing process of electrical tree due to the water tree. All of these growing process is analyzed quantitatively by image measurement program composed of borland c++. We fabricated the thin film type specimen to observe water tree easier and also the needle electrode was prepared by etching method using electrolytes. Initiation and the growth of three was observed somewhat different depending on the applied voltage and the water electrode. AgNO$_3$solution electrode accelerates the initiation and the growth of water tree, compared to those of distilled water electrode. The water and the electrical tree occurred by water tree has discontinuous growth characteristic.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.287-287
• /
• 2010

We report a new direct patterning method, called liquid bridge-mediated nanotransfer molding (LB-nTM), for the formation of two- or three-dimensional structures with feature sizes between tens of nanometers and tens of micron over large areas. LB-nTM is based on the direct transfer of various materials from a mold to a substrate via a liquid bridge between them. This procedure can be adopted for automated direct printing machines that generate patterns of functional materials with a wide range of feature sizes on diverse substrates. Arrays of TIPS-PEN TFTs were fabricated on 4" polyethersulfone (PES) substrates by LB-nTM using PDMS molds. An inverted staggered structure was employed in the TFT device fabrication. A 150 nm-thick indium-tin oxide (ITO) gate electrode and a 200 nm-thick SiO2dielectric layer were formed on a PES substrate by sputter deposition. An array of TIPS-PEN patterns (thickness: 60 nm) as active channel layers was fabricated on the substrate by LB-nTM. The nominal channel length of the TIPS-PEN TFT was 10 mm, while the channel width was 135 mm. Finally, the source and drain electrodes of 200 nm-thick Ag were defined on the substrate by LB-nTM. The TIPS-PEN TFTs can endure strenuous bending and are also transparent in the visible range, and therefore potentially useful for flexible and invisible electronics.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.11C no.2
• /
• pp.32-36
• /
• 2001

We investigate the surface order, defects and morphology of hexagonal columnar mesophases, Having a crown ether at one end which forms the center of the column and three fluorinated tails at the other, The orientation of the columns was successfully controlled by surface anchoring: Columns were aligned perpendicularly to an evaporated carbon surface, and the planar alignment do asymmetric compounds was induced by a water surface. TEM images show that there is a high degree of perfection in the packing do the cylinders. The hexagonal columnar mesophase (F(sub)h) was confirmed by direct images and the corresponding electron diffractions, where ordered cylindrical moieties are packed on a hexagonal lattice. The column of 12F8-ABG-15C5 was much straighter, compared with that of 12F8-AG-B15C5, resulting from the degrees of regular stacking. Elementary edge dislocation, grain boundary and +1/2 disclination have been observed, although the defects are generally rare.

• Journal of the Korean institute of surface engineering
• /
• v.19 no.3
• /
• pp.92-108
• /
• 1986

An electroplating on the lead frame fabricated from domestic copper plate was studied experimentally. In this study, nickel was plated on the thin copper lead frame and silver layer was coated on the nickel film in the cyanide electrolyte. The effect of process variables such as current density, plating time, coating thickness and flow rate of electrolytic solution on the properties of coating was investigated. Some samples on each step were fabricated during electroplating. The results obtained from polarization measurement, observation of SEM photograph, adhesion test of coating and microhardness test are as follows. On silver plating, polarization resistance of potentiostatic cathodic polarization curve is reduced as the flow rate of Ag electrolytic solution increases. And above resistance is also reduced when the minor chemicals of sodium cyanide and sodium carbonate are added in potassium silver cyanide bath. The reduced polarization resistance makes silver deposition on the cathode easy. An increase in the current density and the coating thickness causes the particle size of deposit to coarsen, and consequently the Knoop microhardness of the coating decreases. On selective plating an increase in the flow rate of plating solution lead to do high speed plating with high current density. In this case, the surface morphology of deposit is of fine microstructure with high Knoop hardness. An increasing trend of the adhesion of coating was shown with increasing the current density and flow rate of electrolytic solution.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.4
• /
• pp.348-352
• /
• 2022

Resistive switching behaviors of a co-sputtered zinc silicate thin film (ZnO and SiO₂ targets) have been investigated. We fabricated an Ag/ZnSiO_x/highly doped n-type Si substrate device by using an RF magnetron sputter system. X-ray diffraction pattern (XRD) indicated that the Zn₂SiO₄ was formed by a post annealing process. A unique morphology was observed by scanning electron microscope (SEM) and atomic force microscope (AFM). As a result of annealing process, 50 nm sized nano clusters were formed spontaneously in 200~300 nm sized grains. The device showed a unipolar resistive switching process. The average value of the ratio of the resistance change between the high resistance state (HRS) and the low resistance state (LRS) was about 106 when the readout voltage (0.5 V) was achieved. Resistance ratio is not degraded during 50 switching cycles. The conduction mechanisms were explained by using Ohmic conduction for the LRS and Schottky emission for the HRS.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.151-151
• /
• 2012

A new plasma process, i.e., the combination of PIII&D and HIPIMS, was developed to implant non-gaseous ions into materials surface. HIPIMS is a special mode of operation of pulsed-DC magnetron sputtering, in which high pulsed DC power exceeding ~1 kW/$cm^2$ of its peak power density is applied to the magnetron sputtering target while the average power density remains manageable to the cooling capacity of the equipment by using a very small duty ratio of operation. Due to the high peak power density applied to the sputtering target, a large fraction of sputtered atoms is ionized. If the negative high voltage pulse applied to the sample stage in PIII&D system is synchronized with the pulsed plasma of sputtered target material by HIPIMS operation, the implantation of non-gaseous ions can be successfully accomplished. The new process has great advantage that thin film deposition and non-gaseous ion implantation along with in-situ film modification can be achieved in a single plasma chamber. Even broader application areas of PIII&D technology are believed to be envisaged by this newly developed process. In one application of non-gaseous plasma immersion ion implantation, Ge ions were implanted into SiO2 thin film at 60 keV to form Ge quantum dots embedded in SiO2 dielectric material. The crystalline Ge quantum dots were shown to be 5~10 nm in size and well dispersed in SiO2 matrix. In another application, Ag ions were implanted into SS-304 substrate to endow the anti-microbial property of the surface. Yet another bio-application was Mg ion implantation into Ti to improve its osteointegration property for bone implants. Catalyst is another promising application field of nongaseous plasma immersion ion implantation because ion implantation results in atomically dispersed catalytic agents with high surface to volume ratio. Pt ions were implanted into the surface of Al2O3 catalytic supporter and its H2 generation property was measured for DME reforming catalyst. In this talk, a newly developed, non-gaseous plasma immersion ion implantation technique and its applications would be shown and discussed.