• 한국세라믹학회지
• /
• 제44권4호
• /
• pp.208-213
• /
• 2007

Alumina/silver ($Al_2O_3/Ag$) nanocomposites with Ag content up to 9 vol% were prepared from nanopowder by soaking method using ${\gamma}-Al_2O_3$ of needle type and spark plasma sintering (SPS). The mechanical properties of specimens were investigated three-point flexural strength and toughness as a function of the Ag contents. The maximum flexural strength of the alumina/silver nanocomposite was 850 MPa for the 1 vol% composite, and also higher than monolith alumina as about 800 MPa at 3, 5, and 7 vol% Ag contents. Fracture toughness by single edged V-notch beam (SEVNB) was $4.05MPa{\cdot}m^{1/2}$ for the 3 vol% composite and maintained about $4.00MPa{\cdot}m^{1/2}$ at 5, and 7 vol% Ag content. Microstructure of fracture surface for each fracture specimens was observed. Due to the inhibition effect of alumina grain growth, the average grain size of nanocomposites depends on the content of Ag nano particles. The fracture morphology of nanocomposite with dislocation (sub-grain boundary) by silver nano-particles of second phases in the alumina matrix also showed transgranular fracture-mode compare with intergranular of monolith alumina. Thermal conductivity of specimens at room temperature was about 40 W/mK for the 1 vol% Ag content.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.II
• /
• pp.1248-1251
• /
• 2005

In PDP, a transparent dielectric is formed on a front glass substrate so as to cover bus electrodes (Ag). During the fabrication process, sometimes, a transparent dielectric reacts with bus (Ag) electrode in the range of $560-600^{\circ}C$, and the reaction gives the dielectric its yellow coloration, what is called "yellowing phenomena". In this paper, we investigated the reaction between bus electrode and transparent dielectric covered with different frit content in Ag paste.

• 농업과학연구
• /
• 제9권2호
• /
• pp.453-460
• /
• 1982

개나리에 있어서 $AgNO_3$ 용액살포(溶液撒布)가 $SO_2$가스의 피해경감(被害輕減)에 미친는 효과(效果)를 시험(試驗)하였던 바 다음과 같은 결과(結果)를 얻었다. 1. $AgNO_3$ 용액(溶液)은 살포농도(撒布濃度)가 200 ppm 이상으로 되면 잎의 뒷면에 미세(微細)한 흑색반점(黑色斑點)을 발생(發生)시켰으며 100ppm으로 처리(處理)되었을 때 $SO_2$가스 피해(被害)로 일어나는 낙엽현상(落葉現狀)과 가시피해(可視被害)를 현저(顯著)히 경감(輕減)시켰다. 2. $AgNO_3$ 용액살포(溶液撒布)는 $SO_2$가스 피해(被害)로 발생(發生)되는 pH의 저하(低下)와 chlorophyll 함량(含量)의 감소현상(減少現狀)을 억제(抑制)시켰으며, peroxidase의 활성(活性)을 증가(增加)시켰다. 3. $AgNO_3$ 용액(溶液)의 살포(撒布)는 $SO_2$가스의 흡수(吸收)와 기공(氣孔)의 개폐(開閉)에 영향(影響)을 미치지 않았다.

• 한국주조공학회지
• /
• 제28권4호
• /
• pp.184-189
• /
• 2008

Ag-Cd alloy has been widely used as an electrical contact material, since Ag-Cd alloy has a good wear resistance and stable contact resistance. But nowadays Ag-Cd alloy is not considered as electrical contact material any more due to detrimental effect on environments. Currently, active researches are being performed on ($Ag-SnO_2$ and $Ag-SnO_{2}-In_{2}O_{3}$) as an alternative solution which can fix the remaining environmental problems. However, $In_{2}O_{3}$ is relatively expensive and Ag-Sn alloy has low wear resistance. Our recent research results show that Ag-X%Zn-Y%Sn has similar physical and chemical properties. In the present study, so we tried to change and to optimize the Zn oxide content to over 6 wt% and Sn oxide content with 0.5, 1.0, 1.5 wt%. Results obtained from the experiments on the Ag-X%ZnO-Y%$SnO_2$ are discussed.

• 환경생물
• /
• 제20권2호
• /
• pp.136-145
• /
• 2002

Ag와 Cu로 오염된 퇴적물이 이매패류 Macoma balthica에 미치는 만성독성영향과 주요한 중금속 흡수경로를 평가하기 위해, 실험실에서 미소생태계 실험이 수행되었다. 실험생물인 M. balthica는 4개의 농도구배를 갖는 $Ag(0.01-0.87\mu{mol}\;g^{-1})$와 $Cu(0.75-5.55\mu{mol\;g^{-1})$로 오염된 퇴적물에서 90일 동안 배양되었다. 퇴적물 내 중금속의 지화학적 분포 특성과 생물이용도를 조절한다고 알려진 AVS(acid volatile sulfide)의 농도를 변화시켜, AVS가 M. balthica의 Ag와 Cu의 체내축적에 미치는 영향을 평가하였다. 90일간 노출된 후, M. balthica가 축적한 Ag와 Cu의 농도는 1 N HCI로 추출된 퇴적물 내 중금속의 농도(SEM, simultaneously extracted metal)와 양의 상관성을 보이며 증가하였다. Ag와 Cu의 체내 축적은 [SEM]-[AVS]값에 큰 영향을 받지 않았는데, 이것은 공극수 내 용존태로 존재하는 Ag와 Cu가 생물 체내 축적에 크게 기여하지 않았다는 것을 암시한다. 체내 축적된 Ag와 Cu는 M. balthica의 여수율과 글리코겐 함량에 직접적인 영향을 미쳤다. 최대 $1.0\pm{0.2}\mu{mol}\;Ag\;g^{-1}$와 $2.7\pm{0.3}\mu{mol}\;Cu\;g^{-1}$를 축적한 M. balthica의 여수율은 오염되지 않은 퇴적물에 노출된 실험조개의 18-43%에 불과하였다. 이와 유사하게, 중금속 처리군에 노출된 M. balthica의 글리코겐 함량은 체내 Ag와 Cu의 농도와 음의 상관성을 나타내었다. 본 연구의 결과는 Ag와 Cu로 오염된 퇴적물에 노출된 M. balthica는 주로 퇴적물의 섭식을 통해 중금속을 축적하며, 여수율과 글리코겐 함량의 감소와 같은 만성독성영향을 나타낼 수 있다는 것을 암시한다.

• 마이크로전자및패키징학회지
• /
• 제20권3호
• /
• pp.53-57
• /
• 2013

Sn-3.0Ag-0.5Cu 무연솔더에서 Ag 함량의 감소는 기계적 충격 신뢰성 향상에 도움이 되는 반면 솔더링성을 저하시키는 것으로 알려져 있다. 본 연구에서는 저 Ag함유 무연솔더의 솔더링성 향상을 위해 In을 첨가한 Sn-1.2Ag-0.7Cu-0.4In 4원계 조성과 여기에 미량의 Mn 및 Pd을 첨가한 무연솔더 조성에 대하여 솔더 젖음성을 평가하고, 보드 레벨 BGA 패키지의 열싸이클링 및 기계적 충격 신뢰성을 평가하였다. Sn-1.2Ag-0.7Cu 조성에 0.4 wt% In을 첨가한 합금의 젖음성은 Sn-3.0Ag-0.5Cu에 근접한 수준으로 향상되었으나, 패키지의 열싸이클링 신뢰성은 Sn-3.0Ag-0.5Cu에 미치지 못하는 것으로 나타났다. Sn-1.2Ag-0.7Cu-0.4In 조성에 0.03 wt% Pd의 첨가는 솔더 젖음성 및 패키지 신뢰성을 저하시킨 반면에 0.1 wt% Mn을 첨가한 합금은 특히 기계적 충격 신뢰성이 Sn-3.0Ag-0.5Cu는 물론 Sn-1.0Ag-0.5Cu보다도 우수한 수준으로 향상되었는데, 이는 Mn 첨가가 합금의 모듈러스를 감소시킨 데에 기인하는 것으로 생각된다.

• Transactions on Electrical and Electronic Materials
• /
• 제15권5호
• /
• pp.275-278
• /
• 2014

We deposited TiAgN and ZrAgN nanocomposite coatings on pure Titanium specimens, by using arc ion plating (AIP) with single alloy targets. TiAg ZrAg alloy targets of 5 wt.%, 10 wt.% silver content by vacuum arc remelting (VAR), followed by homogenization for 2 hours at $1,100^{\circ}C$ in non-active Ar gas atmosphere and characterized these samples for morphology and chemical composition. We investigated the biocompatibility of TiAg and ZrAg alloys by examining the proliferation of L929 fibroblast cells by MTT test assay, after culturing the cells ($4{\times}10^4cells/cm^2$) for 24 hours; and exploring the antibacterial properties of thin films by culturing Streptococus Mutans (KCTC3065), using paper disk techniques. Our results showed no cytotoxic effects in any of the specimens, but the antibacterial effects against Streptococus Mutans appeared only in the 10 wt.% silver content specimens.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 춘계학술대회 논문집 초전도 자성체 연구회
• /
• pp.69-72
• /
• 2003

Bi-2223 superconducting wires were fabricated by stacking, drawing process with different precursor powders and different heat-treatment histories. The precursor powders were 2 kinds of Pb content. And a part of the tapes were experienced pre-annealing process which caused tetragonal structure of Bi-2212 phase to orthorhombic structure of it was during drawing process. We confirmed the transformation of Bi-2212 phase from tetragonal structure to orthorhombic structure and reduction of second phases. XRD and DC magnetization analysis were performed in order to investigate the fraction of Bi-2223 phase in Bi-2223/Ag HTS tape. We could achieve best Ic of 70 A class at the Bi-2223/Ag tape using low Pb content of precursor powder and experienced pre-annealing process. DC magnetization analysis was useful to investigate the fraction of Bi-2223 phase in the Bi-2223/Ag tape.

• 한국응용과학기술학회지
• /
• 제31권2호
• /
• pp.313-319
• /
• 2014

This study was performed to obtain high conversion efficiency of $NH_3$ and minimize generation of nitrogen oxides using metal-supported catalyst with Ag : Cu ratio. Through structural analysis of the prepared catalyst with Ag : Cu ratio ((10-x)Ag-xCu ($0{\leq}x{\leq}6$)), it was confirmed that the specific surface area was decrease with increasing metal content. A prepared catalysts showed Type II adsorption isotherms regardless of the ratio Ag : Cu of metal content, and crystalline phase of $Ag_2O$, CuO and $CuAl_2O$ was observed by XRD analysis. In the low temperature($150{\sim}200^{\circ}C$), a conversion efficiency of AC_10 recorded the highest(98%), whereas AC_5 (Ag : Cu = 5 : 5) also showed good conversion efficiency(93.8%). However, in the high temperature range, the amounts of by-products(NO, $NO_2$) formed with AC_5 was lower than that of AC_10. From these results, It is concluded that AC_5 is more environmentally and economically suitable.

• Journal of Electrical Engineering and Technology
• /
• 제12권6호
• /
• pp.2348-2352
• /
• 2017

The electrical contact characteristics including temperature rise, contact resistance and arc erosion rate of the $Ag-SnO_2$ materials with increased $SnO_2$ content were investigated during the repeated make-and-break operations. The thickness of arcing melting layer reduces by half and the arc erosion rate decreases more than 70% under 10000 times operations at AC 10 A with the $SnO_2$ content increasing from 15 wt.% to 45 wt.%, on one hand, temperature rise and contact resistance increase obviously but could be reduced to the same order of conventional $Ag-SnO_2$ materials by increasing the contact force. The microstructure evolution and the effect of $SnO_2$ on the arc erosion, contact resistance were analyzed.