• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.215-216
• /
• 2002

This paper describes the wear characteristics of WC-Co cemented carbides machined with Wire-cut or Die-sinking EOM. We prepared the specimens with different grades of grinding to remove the affected layer after the EDM. These specimens were experimented by block-on-cylinder type tribometer. The result indicated that although the hardness of the affected layer was lower than that of the bulk, wear resistance was increased. In order to investigate the cause of the increase in wear resistance of the affected layer, the layer was observed and analyzed by SEM and ESCA. We also discussed the mean free path of Co phase.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2007년도 춘계학술논문 발표대회
• /
• pp.141-145
• /
• 2007

The part in the structure that is most affected by changes of external temperature is the protective concrete layer that protects a waterproofing layer. Also, the waterproofing layer that is situated under or on the back of such a protective concrete layer is affected by temperature and the behavior of the protective concrete layer under the condition of consolidation or close adhesion. In particular, in many cases, the damage is serious mainly around the projection (such as a parapet), crack, and joint (expansion joint). However, there is no proper way of examining again the non-exposed waterproofing layer once it has been constructed. Therefore, there is an assessment only on the physical property of materials and the capability of the layer in construction, and there is no actual assessment in consideration of its environmental condition or the condition of the use of buildings after construction. Therefore, in order to create more pleasant buildings and to enhance the durability of structures, this study conducts research into the change of capability of non-exposed waterproofing material after the application of a static load and moving load on the waterproofing layer situated under or on the back of protective concrete.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.189-192
• /
• 2008

Turbulent coherent structure near rod-roughened wall are investigated by analyzing the database of direct numerical simulation of turbulent boundary layer. The roughness sublayer id defined as two-point correlations are not independent of streamwise locations around roughness. The roughness sublayer based on the two-point spatial correlation is different from that given by one-point statistics. Quadrant analysis and probability-weighted Reynolds shear stress indicate that turbulent structures are not affected by surface roughness above the roughness sublayer defined by the spatial correlations. The conditionally-averaged flow fields associated with Reynolds shear stress producing Q2/Q4 events show that though turbulent vortices are affected in the roughness sublayer, these are very similar at different streamwise locations above the roughness sublayer. The Reynolds stress producing turbulent vortices in the log layer have almost the same geometrical shape as those in the smooth wall-bounded turbulent flows. This suggests that the mechanism by which the Reynolds stress is produced in the log layer has not been significantly affected by the present surface roughness.

• 대한기계학회논문집B
• /
• 제32권6호
• /
• pp.463-470
• /
• 2008

Turbulent coherent structures near rod-roughened wall are investigated by analyzing the database of direct numerical simulation of turbulent boundary layer. The surface roughness rods with the height $k/{\delta}=0.05$ are arranged periodically in $Re_{\delta}=9000$. The roughness sublayer is defined as two-point correlations are not independent of streamwise locations around roughness. The roughness sublayer based on the two-point spatial correlation is different from that given by one-point statistics. Quadrant analysis and probability-weighted Reynolds shear stress indicate that turbulent structures are not affected by surface roughness above the roughness sublayer defined by the spatial correlations. The conditionally-averaged flow fields associated with Reynolds shear stress producing Q2/Q4 events show that though turbulent vortices are affected in the roughness sublayer, these are very similar at different streamwise locations above the roughness sublayer. The Reynolds stress producing turbulent vortices in the log layer ($y/{\delta}=0.15$)have almost the same geometrical shape as those in the smooth wall-bounded turbulent flows. This suggests that the mechanism by which the Reynolds stress is produced in the log layer has not been significantly affected by the present surface roughness.

• 한국정밀공학회지
• /
• 제5권4호
• /
• pp.59-65
• /
• 1988

This paper describes the transmutation layer of CNC Wire electrical discharte machined surface. In order to analayze and invesigate transmutation layer of the carbon tool steel, workpieces was heat-treated by quenching, tempering, normaling. The obtained results are summarized as follows. 1. The result showed that wire electrical discharge machined surface region was transmuted into the recdast layer in the range of about 10${\mu}$m deep by resolidification and next zone was transmuted into the heat affected zone in the range of about 15${\mu}$m deep by high temperature. 2. The hardness of the recast layer and heat affected zone was decreased on its machined surface. 3. The more wire feedrate was increased, the more electrical discharge machine gap was decreased.

• 한국화재소방학회논문지
• /
• 제16권2호
• /
• pp.38-42
• /
• 2002

ON-OFF 제트를 사용하여 plume의 주기성이 천장아래에 형성되는 연층에 미치는 정성적인 영향을 파악하였다. 사용된 연기는 가열에 의해 증발된 kerosene 입자를 섞은 질소가스이다. Laser sheet에 의해 산란된 유동장의 순간 상들은 디지털 비디오 카메라에 의해 녹화되었다. ON-OFF 제트와 연속제트의 연층형성 과정을 비교하므로서 화원근처에 형성되는 연층은 plume과 천장의 주기적인 충돌에 의해 지배됨을 확인하였다. 또한 plume의 주기적인 충돌은 연층을 두껍게하며, back-flow를 일으킴을 확인하였다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권5호
• /
• pp.281-284
• /
• 1999

In this paper, the electrical conduction, breakdown strength and dielectric properties were investigated in the interfaces of PET films. The volume resistivity and breakdown strength were decreased; especially the specimens with semiconductive layer showed the lowest breakdown strength. This decrease of electrical properties was appeared by increasing charge density in inhomogeneous layer of PET. The dielectric properties of PET did not show significant difference with PET/PET but the films with semiconductive interface layer showed the increase in capacitance and $tan\delta$ was affected by the PET rather than semiconductive layer. It is assumed that the variation of $tan\delta$ was affected by the dielectric polarization and the leakage current(charge).

• Nuclear Engineering and Technology
• /
• 제51권4호
• /
• pp.996-1007
• /
• 2019

We investigated the influence of the aspect ratio (H/R) of the oxide layer on the reactor vessel heating in three-layer configuration. Based on the analogy between heat and mass transfers, we performed mass transfer experiments to achieve high Rayleigh numbers ranging from $6.70{\times}10^{10}$ to $7.84{\times}10^{12}$. Two-dimensional (2-D) semi-circular apparatuses having the internal heat source were used whose surfaces of top, bottom and side simulate the interfaces of the oxide layer with the light metal layer, the heavy metal layer, and the reactor vessel, respectively. Multi-cell flow pattern was identified when the H/R was reduced to 0.47 or less, which promoted the downward heat transfer from the oxide layer and possibly mitigated the focusing effect at the upper metallic layer. The top boundary condition greatly affected the natural convection of the oxide layer due to the presence of secondary flows underneath the cold light metal layer.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제11권1호
• /
• pp.510-520
• /
• 2019

To investigate the morphology characteristics of air layer in the air cavity, a numerical method with the combination of RANS equations and VOF two-phase-flow model is proposed for a plate with air cavity. Based on the model above, the dynamic and developmental process of air layer in the air cavity is studied. Numerical results indicate that the air layer in the plate's air cavity exhibits the dynamic state of morphology and the wavelength of air layer becomes larger with the increasing speed. The morphology of air layer agrees with the Froude similarity law and the formation of the air layer is not affected by the parameters of the cavity, however, the wave pattern of the air layer is influenced by the parameters of the cavity. The stable air layer under the air cavity is important for the resistance reduction for the air layer drag reduction.

• 펄프종이기술
• /
• 제33권1호
• /
• pp.53-61
• /
• 2001

This study was carried out to evaluate the effect of coating pigments on the printability by investigating the pore structure of casting layer such as the number, size and distribution of pores and the pore rate. The coating structure was mainly determined by the interaction between pigment and binder. It means that the structure of pores was chiefly affected by the shape and size distribution of pigments and their packing rate. The physical properties of pore have close relationships with ink set-off, the speed of ink penetration and printing gloss. The results suggested that the rate and number of pores were greatly affected by the particle size distribution and shape of pigments. The rate of pore increased with the reduction of particle size distribution of pigments. Calcite was effective to improve greatly the printability of coated paper.