• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.839-842
• /
• 2002

Some open jet wind tunnels have been operating under limitations due to large pressure fluctuations at some wind tunnel speeds. The Hyundai Aero-acoustic full scale Wind Tunnel (HAWT), which was completed in 1999, shows that most of the specifications were fulfilled but wind tunnel pulsations at some wind speeds were observed. Hyundai Motor Company started the wind tunnel modification in order to solve this problem in 2001. After the modification work the amplitude of pressure fluctuation was reduced and below required level over full wind speed range. Aero-acoustic performance, e.g. background noise, as well as aerodynamic performance were improved after this work.

• Journal of Mechanical Science and Technology
• /
• 제17권2호
• /
• pp.280-287
• /
• 2003

The unsteady flow characteristics and the related noise of separated incompressible laminar boundary layer flows (Re$\sub$$\delta$/* = 614, 868, and 1,063) are numerically investigated. The characteristic lines of the wall pressure are examined to identify the primary noise source, related with the unsteady motion of the vortex at the reattachment point of the separation bubble. The generation and propagation of the vortex-induced noise in the separated laminar boundary layer are computed by the method of Computational Aero-Acoustics (CAA), and the effects of Reynolds number, Mach number and adverse pressure gradient strength are examined.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.768-773
• /
• 2001

The self-noise from blade cascade at off-design points mainly comes from separated boundary layer and vortex sheddings, and is also dependent on blade shape. If the incidence angle to the cascade increases, the stalling in blades may occur and the noise level increases significantly. The hybrid method using acoustic analogy was employed to compute the far-field noise spectra and directivity patterns from the separated vortex shedding at off-design points of the cascade of impeller. This paper is compared with the experimental data of a stationary cascade in the same conditions. The simulated result is in excellent .agreement with the measured data except th slight under-prediction near the maximum radiation angle for a dipole sound.

• Journal of Mechanical Science and Technology
• /
• 제17권4호
• /
• pp.590-598
• /
• 2003

A computational aero-acoustic (CAA) method is used to predict the tonal noise generated from a cavity of automobile door seals or gaps at low flow Mach numbers (A$\_$$\infty$/=0.077 and 0.147) In the present method, the acoustically perturbed Euler equations are solved with the acoustic source term obtained from the unsteady incompressible Navier-Stokes calculations of the cavity flow in self-sustained oscillations. The aerodynamic and acoustic fields are computed for the Reynolds numbers based on the displacement thickness, Re$\_$$\delta$*/=850 and 1620 and their fundamental mode characteristics are investigated. The present method is also verified with the experimentally measured sound pressure level (SPL) spectra.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.1449-1452
• /
• 2006

When fluid at high speed flows over an open cavity, large acoustic pressure fields inside the cavity are produced by fluid/structure interactions at the downstream end of the cavity. The inter-coach spacing is one of the most important sources of the aero-acoustic noise of a high-speed train. This noise can usually be heard as low frequency structure-borne noise inside the train. In this study experiments were performed in order to investigate the effects of mud-flap length on the aeroacoustic noise generation inside high-speed trains. Results of the measurement confirmed that the characteristics of the noise generated from the inter-coach spacing are strongly dependent on the size of the gap. Also investigated are the characteristics of the turbulent flow after the inter-coach spacing and consequent generation of the aeroacoustic noise inside the cabin.

• 한국소음진동공학회논문집
• /
• 제22권5호
• /
• pp.444-450
• /
• 2012

The evaluation of a zonal RANS-LES approach is documented for the prediction of broadband noise generated by the flow past unmodified and serrated airfoil trailing edges at a high Reynolds number. A multi-domain decomposition is considered, where the acoustic sources are resolved with a LES sub-domain embedded in the RANS domain. A stochastic vortex method is used to generate synthetic turbulent perturbations at the RANS-LES interface. The simulations are performed with a general-purpose unstructured control-volume code FLUENT. The far-field noise is calculated using the aeroacoustic analogy of Ffowcs Williams-Hawkings. The results of the simulation are validated through the full-scaled wind turbine acoustic measurements. It is found that the present approach is adequate for predicting noise radiation of serrated trailing edge flow for low noise rotor system.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.800-811
• /
• 2014

Recent developments in the prediction of the contribution of windnoise to the interior SPL have opened a realm of new possibilities in terms of i) how the convective and acoustic sources terms can be identified, ii) how the interaction between the source terms and the side glass can be described and finally iii) how the transfer path from the sources to the interior of the vehicle can be modelled. This work discusses in details these three aspects of wind noise simulation and recommends appropriate methods to deliver required results at the right time based on i) simulation and experimental data availability, ii) design stage at which a decision must be made and iii) time available to deliver these results. Several simulation methods are used to represent the physical phenomena involved such as CFD, FEM, BEM, FE/SEA Coupled and SEA. Furthermore, a 1D and 2D wavenumber transformation is used to extract key parameters such as the convective and the acoustic component of the turbulent flow from CFD and/or experimental data whenever available. This work focuses on the validation of the wind noise source characterization method and the vibro-acoustic models on which the wind noise sources are applied.

• 한국전산유체공학회지
• /
• 제14권1호
• /
• pp.53-61
• /
• 2009

The objective of this research is to design blade planform to reduce high speed impulsive(HSI) noise from a non-lifting helicopter rotor using CFD method and optimization techniques. As for the aero-acoustic analysis, CFD technique for aerodynamic analysis and Kirchhoff's method for the acoustic analysis were used. As for the optimization method, Kriging-based genetic algorithm(GA) model as a high-fidelity optimization method was chosen. Design variables and constraints are determined for arbitrary blade planform. The result shows that the optimized blade planform with high swept-back and taper ratio can reduce HSI noise by suppressing generation of the strong shock wave on blade surface and propagation of the noise to the farfield flow region.

• 한국음향학회지
• /
• 제33권1호
• /
• pp.40-47
• /
• 2014

원심팬 날개 깃에서 발생한 와류와 원심팬 볼루트 사이의 상호작용은 원심팬의 주요한 소음원으로 알려져 있다. 본 연구에서는 저소음 설계의 기초 자료로 활용하기 위하여 원심팬의 주요한 소음원 영역으로 고려되는 원심팬 볼루트 영역을 세분화하여 볼루트 영역내의 상대적 기여도를 분석한다. 주요한 소음원으로부터 방사되는 소음을 예측하기 위해 내부 음장용 복합 전산공력음향학(CAA, Computational Aero-Acoustics) 방법을 사용한다. 이 방법은 전산유체역학(CFD, Computational Fluid Dynamics)과 음향상사법(Acoustic Analogy), 그리고 경계요소법(BEM, Boundary Element Method)을 사용하여 원심팬 내부 유동장으로부터 방사한 소음을 원심팬 외부 음향장에서 예측하는 방법이다. 복합 CAA 방법을 이용한 원심팬 볼루트 영역내의 소음원의 상대적 기여도 분석은 컷-오프영역으로부터 출구영역보다 컷-오프영역으로부터 원심팬 스크롤영역이 전체 소음에 대한 기여도가 높고, 날개 깃의 쉬라우드 영역보다 허브 영역이 전체 소음에 대한 기여도가 높다는 것을 보여준다. 이러한 결과는 향후 저소음 원심팬 개발을 위한 유용한 자료로 활용될 것이다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.563-564
• /
• 2014

Recent developments in the prediction of the contribution of windnoise to the interior SPL have opened a realm of new possibilities in terms of i) how the convective and acoustic sources terms can be identified, ii) how the interaction between the source terms and the side glass can be described and finally iii) how the transfer path from the sources to the interior of the vehicle can be modelled. This work discusses several simulation methods that can be used to represent the physical phenomena involved such as CFD, FEM, BEM, FE/SEA Coupled and SEA. This work focuses on the validation of the wind noise source characterization method and the vibro-acoustic models on which the wind noise sources are applied in the framework of a benchmark proposed by Hyundai Motors Corporation.