• 한국분말재료학회지
• /
• 제20권4호
• /
• pp.245-252
• /
• 2013

This study attempted to manufacture a Cu-Ga coating layer via the cold spray process and to investigate the applicability of the layer as a sputtering target material. In addition, changes made to the microstructure and properties of the layer due to annealing heat treatment were evaluated, compared, and analyzed. The results showed that coating layers with a thickness of 520 mm could be manufactured via the cold spray process under optimal conditions. With the Cu-Ga coating layer, the ${\alpha}$-Cu and $Cu_3Ga$ were found to exist inside the layer regardless of annealing heat treatment. The microstructure that was minute and inhomogeneous prior to thermal treatment changed to homogeneous and dense with a more clear division of phases. A sputtering test was actually conducted using the sputtering target Cu-Ga coating layer (~2 mm thickness) that was additionally manufactured via the cold-spray coating process. Consequently, this test result confirmed that the cold sprayed Cu-Ga coating layer may be applied as a sputtering target material.

• 상하수도학회지
• /
• 제22권4호
• /
• pp.449-454
• /
• 2008

Some pretreatment methods have been proposed to enhance the biodegradability and to shorten the hydrolysis reaction time. By means of efficient pretreatment the suspended solids (SS) can be made of better accessible for the anaerobic bacteria. There are several ways how this can be accomplished, which include biological, mechanical, thermal, and chemical methods. For the sludge solubilization using the cavitation phenomenon, we have tried to develop a pretreatment process consisted of a reactor and pumps. The objectives of this study were to develop a advanced wastewater treatment consisted of IABR and the cavitation with PGA. The most effective removal for organic matter and nutrients were occured when both cavitation pretreatment and ${\gamma}$-PGA were applied at the IABR process. Only small portion of ${\gamma}$-PGA at a rate of 1.38mg/L, was enough to improve sedimentation ability, SS removal efficiencies, and sludge volume reduction. After the sludge solubilization by the cavitation, SCOD increased to 193% and SS decreased to 36%. The removal ratio of BOD was 94.5%, T-N removal ratio was 85.5% and T-P removal ratio was 84.9%. The combination process of the IABR with the cavitation and PGA addition seems to be very effective alternative wastewater treatment process.

• Asian Pacific Journal of Cancer Prevention
• /
• 제17권4호
• /
• pp.1617-1623
• /
• 2016

Cisplatin-based concurrent chemoradiation plays an undisputed key role as definitive treatment in unresectable patients with locally advanced squamous cell carcinoma head and neck or as an organ preservation strategy. Treatment with 100 mg/m2 3-weekly cisplatin is considered the standard of care but is often associated with several adverse events. The optimum drug schedule of administration remains to be defined and presently, there is insufficient data limiting conclusions about the relative tolerability of one regimen over the other. This review addresses regarding the optimal dose schedule of cisplatin focusing mainly on three-weekly and weekly dose of cisplatin based concurrent chemoradiotherapy in locally advanced head and neck cancer with an emphasis on mucositis, dermatitis, systemic toxicity, compliance, and treatment interruptions. To derive a definitive conclusion, large prospective randomized trials are needed directly comparing standard 3-weekly cisplatin ($100mg/m^2$) with weekly schedule ($30-40mg/m^2$) of concurrent cisplatin based chemoradiotherapy in locally advanced squamous cell carcinoma head and neck.

• 열처리공학회지
• /
• 제17권1호
• /
• pp.10-16
• /
• 2004

The aim of this study is to investigate the process conditions on the microstructual changes and mechanical properties of large 7175 aluminum ring roll forgings. The billets range from 370 mm to 720 mm in diameter were homogenized and ring roll forged after direct chill casting. The tensile properties of ring roll forged specimen manufactured with ${\Phi}370mm$ billets were superior to those of ${\Phi}720mm$ billets under $T_6$ condition. Also, these properties showed better than those of military specification under $T_{74}$ treatment. The impact value of ring roll forged specimen under $T_{74}$ treatment increased up to 20% than that of $T_6$ condition. The fracture toughness of ring roll forged specimen manufactured with ${\Phi}370mm$ cast billet showed nearly same level of ${\Phi}720mm$ billet which was processed using MF or Cog free forging followed by ring roll forging.

• Journal of Magnetics
• /
• 제10권4호
• /
• pp.137-141
• /
• 2005

We confirmed that the improvement in properties of magnetic tunnel junctions prepared by radical oxidation after thermal treatment was mostly resulted from the redistribution of oxygen at the $AIOx/Co_{90}Fe_{10}$ interface. The as-deposited Al oxide barrier was oxygen-deficient but most of it re-oxidized into $Al_2O_3$, the thermodynamically stable stoichiometric phase, through thermal treatment. As a result, the effective barrier height was increased from 1.52 eV to 2.27 eV. On the other hand, the effective barrier width was decreased from 8.2 ${\AA}$ to 7.5 ${\AA}$. X-ray absorption spectra of Fe and Co clearly showed that the oxygen in the CoFe layer diffused back into the Al barrier and thereby enriched the barrier to close to a stoichiometirc $Al_2O_3$ phase. The oxygen bonded with Co and Fe diffused back by 6.8 ${\AA}$ and 4.5 ${\AA}$ after thermal treatment, respectively. Our results confirm that controlling the chemical structures of the interface is important to improve the properties of magnetic tunnel junctions.

• 상하수도학회지
• /
• 제19권4호
• /
• pp.462-472
• /
• 2005

This study was carried out to suggest the plans for installation of rural sewage treatment facilities through the analysis of these facilities installed in Chungchongnam-do Province. About 5% of all installation was carried out by the department of wastewater and related environment problems and the other case was carried out by the department of construction or residence. In wastewater caused by 250 and 300 persons, facilities capacity do not exceed about $50m^3/d$, caused by 2,500 and 3,000 persons, $500m^3/d$. Advanced sewage treatment process were first needed in the discharge area where affected the water environment greatly. However, in carrying out the water quality pollutant of the total amount management system in the other areas, they should be driven only over the scale of pollutant quota object facilities standard. Rural sewage must be included in the special accounts according to the regulations of local government, and sewage treatment cost should be collected to manage. Installation type uses integrating joint treatment method in case the distance among villages is short or one treatment facility independently.

• 한국분말재료학회지
• /
• 제22권1호
• /
• pp.32-38
• /
• 2015

The effect of heat treatment environment on the microstructure and properties of tantalum coating layer manufactured by kinetic spraying was examined. Heat treatments are conducted for one hour at $800^{\circ}C$, $900^{\circ}C$, and $1000^{\circ}C$ in two different environments of vacuum and Ar gas. Evaluation of microstructure and physical properties are conducted. High density ${\alpha}$-tantalum single phase coating layer with a porosity of 0.04% and hardness of 550 Hv can be obtained. As heat treatment temperature increases, porosity identically decreases regardless of heat treatment environment (vacuum and Ar gas). Hardness of heat treated coating layer especially in Ar gas environment deceases from 550 Hv to 490 Hv with increasing heat treatment temperature. That in vacuum environment deceases from 550 Hv to 530 Hv. The boundary between particles became vague as heat treatment temperature increases. Oxygen distribution of tantalum coating layer is minute after heat treatment in vacuum environment than Ar gas environment.

• Korean Chemical Engineering Research
• /
• 제52권4호
• /
• pp.413-424
• /
• 2014

에너지원으로 바이오가스에 대한 잠재적 가능성이 인식되면서 최근에 바이오가스의 생산기술을 제고하고 에너지 효율을 개선하기 위한 기술개발이 지속적으로 진행되고 있다. 본 논문의 목적은 혐기성 소화 과정에서 바이오가스 생산을 증가시키기 위한 효과적이고 효율적인 슬러지 전처리 방법에 대하여 분석하였다. 이를 위해 본 논문에서는 각각의 전처리 방법의 장점과 단점을 분석하여 바이오가스 생산에 미치는 영향요인을 비교 분석하였다.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1996년도 추계학술대회
• /
• pp.52-56
• /
• 1996

The elevation of present medical service using advanced science contributes to offer medical examination and treatment of good quality under the subject of patient satisfaction as well as patient impression. The dental service field charging some part of public health promotion and public welfare promotion also intends to improve the dental examination and treatment quality utilizing advanced science. The object of this research is the development of dental patient education system (DPES) using multimedia of new technology. DPES can be employed for these object, harmonious operation of dental examination and treatment, treatment quality improvement, disease notice to patient under the subject of patient satisfaction and patient impression, explanation of some selective treatment course, the verification of treatment necessities and treatment validation, and the improvement of treatment effect through the oral cavity sanitation education in the sense of prevention. This research also serves the development environment, the step to collect educational document, visual information and to structure those, and the examination of DPES efficiency in clinic.

• 대한금속재료학회지
• /
• 제50권7호
• /
• pp.545-548
• /
• 2012

The optical and electronic properties of Indium Tin Oxide (ITO) thin films deposited on a RF-plasma treated glass substrate were investigated by X-Ray Photoelectron Spectroscopy (XPS), Ultra-violet Photoelectron Spectroscopy (UPS), Reflected Electron Energy Loss Spectroscopy (REELS). The modification of glass substrates was carried out by varying the time of the plasma surface treatment in an oxygen atmosphere. The focus of this research was to examine how the optical and electronic properties of ITO thin films change with the plasma treatment time. The surface energy increased since the carbon bonds were removed from the surface after the glass substrate received the surface treatment. The ITO thin films produced on the glass substrate with surface treatment showed that the high optical transmittance was approximately 85%. The measured band gap energy was as high as 3.23 eV when the plasma treatment time was 60 s and the work function after the treatment was increased by 0.5 eV in comparison to that before the treatment of 60 s. The ITO thin film exhibited an excellent sheet resistance of $2.79{\Omega}/{\Box}$. We found that the optical and electronic properties of ITO thin films can be improved by RF-plasma surface treatment.