• 구강회복응용과학지
• /
• 제16권2호
• /
• pp.123-132
• /
• 2000

The field of maxillofacial prosthetics is concerned with the prosthetic reconstruction of missing head and neck tissue. Currently, facial prostheses are usually applied in cases of defects caused by the surgical removal of tumors or congenital defects. While silicone has been most widely used for the reconstruction of missing maxillofacial defects, it does not have ideal physical properties. Therefore, bonding a thin polyurethane sheet to silicone prostheses was recommended. In this case skin adhesives were used for the retention of maxillofacial prostheses. But retention of devices has always been problematic. The contributions of implants can be made to solve these problems. Implants have reduced the need for adhesive use, simplifying cleaning procedures and thus extending the life of the prostheses. For implant-retained prostheses, retentive matrix is necessary to hold attachments and/or magnets. The retentive matrix is usually fabricated with autopolymerizing acrylic resin or visible light- polymerized resin. The purpose of this study was to compare the adhesion-in-peel force of silicone adhesive to autopolymerizing acrylic resin and polyurethane sheet with two different surface textures : pumice polish only or retention groove, and three surface primers : Dow corning 1205 primer or Dow corning S-2260 primer or FactorII A-304 primer, and two polymerization methods : room temperature or dry heat oven. The t-peel bond strength of specimens was determined as described in ASTM Standard D1876-72. The results were statistically analyzed using the ANOVA test, multiple range test and t-test The results were as follows. 1. The t-peel bond strength of A-304 primer was the highest and statistically higher than that of S-2260(p<0.05). 2. The t-peel bond strength of specimens with retention groove was statistically higher than that of specimens polished with pumice(p<0.05). 3. The t-peel bond strength of specimens polymerized in dry heat oven was statistically higher than that of specimens in room temperature(p<0.01).

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 춘계학술대회 논문집 센서 박막재료 반도체 세라믹
• /
• pp.33-36
• /
• 2003

Tungsten is widely used as a plug for the multi-level interconnection structures. However, due to the poor adhesive properties of tungsten (W) on $SiO_2$ layer, the Ti/TiN barrier layer is usually deposited onto $SiO_2$ for increasing adhesion ability with W film. Generally, for the W-CMP (chemical mechanical polishing) process, the passivation layer on the tungsten surface during CMP plays an important role. In this paper, the effect of oxidants controlling the polishing selectivity of W/Ti/TiN layer were investigated. The alumina $(Al_2O_3)$ abrasive containing slurry with 5 % $H_2O_2$ as the oxidizer, was studied. As our preliminary experimental results, very low removal rates were observed for the case of no-oxidant slurry. This low removal rate is only due to the mechanical abrasive force. However, for Ti and TiN with 5 % $H_2O_2$ oxidizer, different removal rate was observed. The removal mechanism of Ti during CMP is mainly due to mechanical abrasive, whereas for TiN, it is due to the formation of metastable soluble peroxide complex.

• 한국임상수의학회지
• /
• 제25권6호
• /
• pp.494-500
• /
• 2008

The aim of this study was to determine the effectiveness of hyaluronic acid-carboxymethylcellulose membrane (GUARDIX-$MB^{(R)}$) barriers on prevention against post-operative peritoneal adhesions. In this study, fourteen mongrel dogs were divided into two experimental groups: 0.1 % hyaluronic acid (0.1HA) group and hyaluronic acidcarboxymethylcellulose membrane (HA-CMC) group. In order to induce adhesions, the anti-mesenteric serosa of the ileum was exteriorized and then abraded in a standard manner by scraping with a scalpel blade to create homogenous petechial hemorrhagic surface over a $1\;{\times}\;1cm$ area. Solution of 0.1HA were simply coated over the abraded tissues, $1.5\;{\times}\;1.5cm$ HA-CMC membrane was placed over the abraded tissues, allowed to spread across the intra-abdominal organs before closure of the abdomen. On day 1 before and day 1, 4, 7, 14, and 21 after operation, venous blood specimens were collected for measurement of fibrinogen and total WBC. The adhesions were blindly assessed 3 weeks later by using a computerized tensiometer. The fibrinogen and total WBC values of two groups showed no statistical significances. The mean tensile strength (gram force, gf) of formed adhesions day 21 after surgery was $88.1\;{\pm}\;55.70gf$ in the 0.1 % HA group and $24.8\;{\pm}\;22.69gf$ in the HA-CMC group. The tensile strength values of adhesion separation HA-CMC membrane group was significantly lower than the 0.1HA group (p<0.05). Therefore, we suggest that HACMC membrane reduce peritoneal adhesions may be applicable to preventing post-operative intraperitoneal adhesions in dogs.

• 한국컴퓨터그래픽스학회논문지
• /
• 제25권4호
• /
• pp.1-8
• /
• 2019

본 논문에서는 젖은 헤어나 털에서 분사되는 액체의 디테일한 움직임을 표현할 수 있는 새로운 프레임워크를 제안한다. 젖은 헤어에서는 모발의 마찰력과 접착력 뿐만 아니라, 액체의 움직임도 마른 헤어에 비해 독특한 움직임을 갖는다. 하지만, 최근에 제안된 기법들도 모발의 접착력과 마찰력만을 고려했으며, 젖은 헤어에서 분사되는 액체의 움직임은 개선시키지 못했다. 이 문제는 헤어와 유체의 상호작용에서 표현되는 디테일한 특징을 잡아내지 못하기 때문에 결과의 품질을 저하시키는 원인이 된다. 본 논문의 주안점은 이 문제를 완화시켜 결과의 품질을 개선시키는 것이며, 결과적으로 FLIP(Fluid-implicit particle) 기반 유체 시뮬레이션과 헤어 입자 간의 상호작용을 효율적으로 표현할 수 있는 결합 프레임워크를 제안한다. 제안하는 방법은 이전 연구들에서 표현하지 못했던 곡선 형태로 분사되는 액체의 디테일한 움직임을 젖은 헤어 프레임워크에서 표현해냈다.

• 한국추진공학회지
• /
• 제24권3호
• /
• pp.12-17
• /
• 2020

황색 산화철을 적용한 추진제의 기계적 특성은 적색산화철을 적용한 추진제와 비교하여 기계적물성이 다소 증가하였다. 또한 황색산화철을 적용한 추진제는 두 종류의 AP 입자를 사용하였으며 총량을 유지하고 작은 입자의 AP 비율 증가 시 연소속도가 증가하였다. 황색산화철을 첨가한 추진제는 압력 지수 값이 0.5인 17.5 mm/sec 이하의 운용조건에서 추진기관에 적용 가능하다. 혼합 믹서 Scale-up 시연소속도 감소, 최대인장강도 감소, 최대인장강도에서의 연신율은 증가하였다. 황색산화철은 내열재/라이너/추진제 사이의 접착력에는 큰 영향을 끼치지 않는다.

• Composites Research
• /
• 제35권2호
• /
• pp.86-92
• /
• 2022

본 연구에서는 접착제를 구성하는 분자 결합 구조의 차이가 열가소성 복합재의 계면 특성에 미치는 영향을 판단하기 위해 진행되었다. 고온 오븐 접합 공정을 이용하여 carbonfiber/polyetherketoneketone(CF/PEKK) 열가소성 복합재료를 융합 접합, polyetheretherketone(PEEK), polyetherimide(PEI) 접착제 접합하였다. 그리고 lap 전단 강도 시험과 디지털 광학 현미경과 주사 전자 현미경을 이용한 파단면 분석, FTIR 분석을 수행하였다. 그 결과, 접착제 접합은 CF/PEKK와 접착제를 구성하는 주요 결합기인 에테르기, 케톤기, 이미드기의 결합이 증가한 인터페이즈를 형성하여 접착 강도를 강화시켰다. 그리고, 에테르기와 케톤기를 더 많이 함유한 PEEK를 사용하는 것이 더 강한 결합력을 갖는 인터페이즈를 형성하여, 복합재의 접착 강도를 향상시켰다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.533-537
• /
• 2003

Compared to sintered polycrystalline diamond (PCD), the deposited thin film diamond has a great advantage on the fabrication of cutting tools with complex geometries such as drills. Because of high performance in high speed machining non-ferrous difficult-to-cut materials in the field of automobiles industry, aeronautics and astronautics industry, diamond-coated drills find large potentialities in commercial applications. However, the poor adhesion of the diamond film on the substrate and high surface roughness of the drill flute adversely affect the tool lift and machining quality and they become the main technical barriers for the successful development and commercialization of diamond-coated drills. In this paper, diamond thin films were deposited on the commercial WC-Co based drills by the electron aided hot filament chemical vapor deposition (EACVD). A new multiple coating technology based on changing gas pressure in different process stages was developed. The large triangular faceted diamond grains may have great contribution to the adhesive strength between the film and the substrate, and the overlapping ball like blocks consisted of nanometer sized diamond crystals may contribute much to the very low roughness of diamond film. Adhesive strength and quality of diamond film were evaluated by scanning electron microscope (SEM), atomic force microscope (AFM), Raman spectrum and drilling experiments. The ring-block tribological experiments were also conducted and the results revealed that the friction coefficient increased with the surface roughness of the diamond film. From a practical viewpoint, the cutting performances of diamond-coated drills were studied by drilling the SiC particles reinforced aluminum-matrix composite. The good adhesive strength and low surface roughness of flute were proved to be beneficial to the good chip evacuation and the decrease of thrust and consequently led to a prolonged tool lift and an improved machining quality. The wear mechanism of diamond-coated drills is the abrasive mechanical attrition.

• Journal of Ceramic Processing Research
• /
• 제13권spc2호
• /
• pp.328-331
• /
• 2012

With the recent development of super-precision optical instruments, camera modules for devices, such as portable terminals and digital camera lenses, are increasingly being used. Since an optical lens is usually produced by high-temperature compression molding methods using tungsten carbide (WC) alloy molding cores, it is necessary to develop and study technology for super-precision processing of molding cores and coatings for the core surface. In this study, Rhenium-Iridium (Re-Ir) thin films were deposited onto a WC molding core using a sputtering system. The Re-Ir thin films were prepared by a multi-target sputtering technique, using iridium, rhenium, and chromium as the sources. Argon and nitrogen were introduced through an inlet into the chamber to be the plasma and reactive gases. The Re-Ir thin films were prepared with targets having a composition ratio of 30 : 70, and the Re-Ir thin films were formed with a 240 nm thickness. Re-Ir thin films on WC molding core were analyzed by scanning electron microscope (SEM), atomic force microscope (AFM), and Ra (the arithmetical average surface roughness). Also, adhesion strength and coefficient friction of Re-Ir thin films were examined. The Re-Ir coating technique has received intensive attention in the coating processes field because of promising features, such as hardness, high elasticity, abrasion resistance and mechanical stability that result from the process. Re-Ir coating technique has also been applied widely in industrial and biomedical applications. In this study, WC molding core was manufactured, using high-performance precision machining and the effects of the Re-Ir coating on the surface roughness.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.176-177
• /
• 2013

Surface plasmon polaritons (SPPs) have attracted the attention of scientists and engineers involved in a wide area of research, microscopy, diagnostics and sensing. SPPs are waves that propagate along the surface of a conductor, usually metals. These are essentially light waves that are trapped on the surface because of their interaction with the free electrons of conductor. In this interaction, the free electrons respond collectively by oscillating in resonance with the light wave. The resonant interaction between the surface charge oscillation and the electromagnetic field of the light constitutes the SPPs and gives rise to its unique properties. In this papers, we studied theoretical and experimental extraordinary transmittance (T) and reflectance (R) of 2 dimensional metal hole array (2D-MHA) on GaAs in consideration of the diffraction orders. The 2d-MHAs was fabricated using ultra-violet photolithography, electron-beam evaporation and standard lift-off process with pitches ranging from 1.8 to $3.2{\mu}m$ and diameter of half of pitch, and was deposited 5-nm thick layer of titanium (Ti) as an adhesion layer and 50-nm thick layer of gold (Au) on the semiinsulating GaAs substrate. We employed both the commercial software (CST Microwave Studio: Computer Simulation Technology GmbH, Darmstadt, Germany) based on a finite integration technique (FIT) and a rigorous coupled wave analysis (RCWA) to calculate transmittance and reflectance. The transmittance was measured at a normal incident, and the reflectance was measured at variable incident angle of range between $30^{\circ}{\sim}80^{\circ}$ with a Nicolet Fourier transmission infrared (FTIR) spectrometer with a KBr beam splitter and a MCT detector. For MHAs of pitch (P), the peaks ${\lambda}$ max in the normal incidence transmittance spectra can be indentified approximately from SP dispersion relation, that is frequency-dependent SP wave vector (ksp). Shown in Fig. 1 is the transmission of P=2.2 um sample at normal incidence. We attribute the observation to be a result of FTIR system may be able to collect the transmitted light with higher diffraction order than 0th order. This is confirmed by calculations: for the MHAs, diffraction efficiency in (0, 0) diffracted orders is lower than in the (${\pm}x$, ${\pm}y$) diffracted orders. To further investigate the result, we calculated the angular dependent transmission of P=2.2 um sample (Fig. 2). The incident angle varies from 30o to 70o with a 10o increment. We also found the splitting character on reflectance measurement. The splitting effect is considered a results of SPPs assisted diffraction process by oblique incidence.

• Composites Research
• /
• 제30권4호
• /
• pp.241-246
• /
• 2017

취성을 가진 섬유강화플라스틱은 충격을 받을 때 충격에너지를 흡수하면서 섬유와 기지재 간 계면에서 탈착 및 박리가 일어난다. 이는 복합재료의 에너지 충격흡수정도의 지표로 삼을 수 있다. 복합재료의 취성을 해결하기 위해 pine과 복합재료의 접착에 대한 연구가 되어 지고 있다. 이번 연구에서는 열처리 된 pine이 탄소섬유강화복합재료와 에폭시 접착제를 이용하여 접착되었다. 최적의 열처리 조건을 확인하기 위해, pine을 160도 및 200도 조건하에 열처리를 하였다. Pine 및 pine/탄소섬유복합재료의 기계적 및 계면물성을 파악하기 위해 인장, 인장중첩전단 및 아이조드 실험을 하였다. 또한, 열처리에 따른 나뭇결간의 결합력을 확인하기 위해 나뭇결 수직방향으로 인장시편 제조 후 파단될 때 탄성파를 음향방출시스템을 이용하여 분석하였다. 160도 조건으로 열처리 했을 때 나무강화 효과로 기계, 계면 및 나뭇결간의 결합력이 좋은 것을 확인하였다. 그러나 과한 열을 주게 되면 열에 약한 헤미셀룰로오스가 분해되면서 잡아주는 인자가 줄어들어 물성이 감소하였다.