• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.418-418
• /
• 2009

Vertically aligned arrays of multi-walled carbon nanotube (MWCNT) on layered Si substrates have been synthesized by water-assisted thermal chemical vapor deposition (CVD). We studied changes in growth by parameters of growth temperature, growth time, rates of gas and annealing time of catalyst. Also, We grew CNTs by adding a little amount of water vapor to enhance the growth of CNTs. $H_2$, Ar, and $C_2H_2$ were used as carrier gas and feedstock, respectively. Before growth, Fe served as catalyst, underneath which AI were coated as an underlayer and a diffusion barrier, respectively, on the Si substrate. The water vapor had a greater effect on the growth of CNTs on a smaller thickness of catalyst. When the water vapor was introduced, the growth of CNTs was enhanced than without water. CNTs grew 1.29 mm for 10 min long by adding the water vapor, while CNTs were 0.73 mm long without water vapor for the same period of time. CNTs grew up to 1.97 mm for 30 min prior to growth termination under adding water vapor. As-grown CNTs were characterized by using scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM), and Raman spectroscopy.

• 한국전기전자재료학회논문지
• /
• 제18권5호
• /
• pp.484-489
• /
• 2005

Because of its effectiveness for the PD(Partial Discharge) pattern recognition, PSA(Pulse Sequence Analysis) has been considered as a new analytic method instead of conventional PRPDA(Phase Resolved Partial Discharge Analysis). However, it is generally thought that PSA has some possibility to misjudge patterns in case of data-missing resulting from poor sensitivity because it analyses the correlation between sequential pulses, which leads to hesitate to apply it to on-site. Therefore, in this paper, the problems of PSA such as data-missing and noise-adding cases were investigated. for the purpose, PD data obtained from various defects including noise-adding data were used and analyzed. As a result, it was shown that both cases could cause fatal errors in recognizing PD patterns. In case of the data missing, the error was dependant on the kinds of defect and the degree of degradation Also, it could be noticed that the error due to adding noises was larger than that due to some data missing.

• Bulletin of the Korean Chemical Society
• /
• 제22권7호
• /
• pp.716-720
• /
• 2001

To test the metal ion effect, hydrolysis experiments for two cellobiohydrolases (CBHⅠ and CBH Ⅱ) from Trichoderma reesei have been carried out in the presence of 10 mM metal ions, such as Cu++, Mn++, Ca++, Hg++, Ba++, Pb++, and Cd++. The addition of Mn++, Ba++, and Ca++(10 mM) during the hydrolysis of Avicel PH 101 caused an increase in the total reducing sugar (TRS) for CBH Ⅰ by 142, 135, and 114 percent, respectively. Those for CBH Ⅱ increased by 177, 175, and 115 percent, respectively. The Mn++ was the most stimulatory metal ion, whereas Hg++ was the most inhibitory metal ion. The adsorption experiments were performed to investigate how the influence of Mn++ and Hg++ on the hydrolysis is related to the adsorption of cellobiohydrolases on cellulose. The increase in TRS during hydrolysis by adding Mn++ caused an increase in adsorption affinity (Kad) and tightness (ΔHa). While, the decrease of TRS during hydrolysis by adding Hg++ caused a decrease in the adsorption affinity (Kad) and tightness (ΔHa). These results indicate the changes in the tightness and affinity of adsorption by adding metal ions play a crucial role in the degradation of the microcrystalline cellulose.

• Bulletin of the Korean Chemical Society
• /
• 제18권3호
• /
• pp.300-305
• /
• 1997

Effect of a nonionic surfactant, Tween 20 on the adsorption and kinetic mechanism for the hydrolysis of a microcrystalline cellulose, Avicel PH 101, by endoglucanase Ⅰ (Endo Ⅰ) and exoglucanase Ⅱ (Exo Ⅱ) isolated from Trichoderma viride were studied. The Langmuir isotherm parameters, amount of maximum adsorption (Amax) and adsorption equilibrium constant (Kad) for the adsorption, were obtained in the presence and the absence of nonionic surfactant. On the addition of Tween 20, the Kad and Amax values of Exo Ⅱ were decreased, while those of Endo Ⅰ were not affected. These indicate that the adsorption affinity of Exo Ⅱ on the cellulose is weakened by nonionic surfactant, and the surfactant enhanced desorption of Exo Ⅱ from insoluble substrate. The enzymatic hydrolysis of the cellulose can be described by two parallel pseudo-first order reactions using the percentages of easily (Ca) and hardly (Cb) hydrolyzable cellulose in Avicel PH 101 and associated rate constants (ka and kb). The Ca value was increased by adding Tween 20 for all enzyme samples (Exo Ⅱ, Endo Ⅰ and their 1:1 mixture) implying that the low-ordered crystalline fraction in the cellulose may be partly dispersed by surfactant. The ka value was not affect by adding Tween 20 for all enzyme samples (Exo Ⅱ, Endo Ⅰ and their 1:1 mixture). The kb value of Exo Ⅱ was increased by adding Tween 20, while that of Endo Ⅰ was not affected. This suggests that the surfactant helps the Exo Ⅱ desorb from microcrystalline cellulose, and increase the hydrolysis rate. These results were show that the increase of hydrolysis of cellulose by the nonionic surfactant is due to both the activation of Exo Ⅱ and partial defibrillation of the cellulose.

• Steel and Composite Structures
• /
• 제45권5호
• /
• pp.665-682
• /
• 2022

In the current study, punching behavior of Reinforced concrete (RC) isolated footings was experimentally and numerically investigated. The experimental program consisted of four half-scale RC isolated footing specimens. The test matrix was proposed to show effect of footing area, reinforcement mesh ratio, adding internal longitudinal reinforcement bars and stirrups on the punching response of RC isolated footings. Footings area varied from 1200×1200 mm2 to 1500×1500 mm2 while the mesh reinforcement ratio was in the range from 0.36 to 0.45%. On the other hand, a 3D non-linear finite element model was constructed using ABAQUS/standard program and verified against the experimental program. The numerical results agreed well with the experimental records. The validated numerical model was used to study effect of concrete compressive strength; longitudinal reinforcement bars ratio and stirrups concentration along one or two directions on the ultimate load, deflection, stiffness and failure patterns of RC isolated footings. Results concluded that adding longitudinal reinforcement bars did not significantly affect the punching response of RC isolated footings even high steel ratios were used. On the contrary, as the stirrups ratio increased, the ultimate load of RC isolated footings increased. Footing with stirrups ratio of 1.5% had ultimate load equal to 1331 kN, 19.6% higher than the bare footing. Moreover, adding stirrups along two directions with lower ratio (0.5 and 0.7%) significantly enhanced the ultimate load of RC isolated footings compared to their counterparts with higher stirrups ratio (1.0 and 1.5%).

• Geomechanics and Engineering
• /
• 제33권1호
• /
• pp.19-27
• /
• 2023

A series of experiments were performed to evaluate the effects of activated carbon on the compressive strength and air content of Portland Cement Concrete (PCC). Activated carbon/PCC composites were prepared by mixing concrete components with commercial activated carbon granules with weight fractions of 0, 0.5%, 1%, and 2% to cement. All PCC specimens were then tested for compressive strength on 7, 14, 21, and 28 days. The experimental results showed that adding 0.5% of activated carbon increased the compressive strength significantly over the curing periods compared to the normal PCC without activated carbon. For the specimens has 0.5% activated carbon, the 7, 14, 21, and 28-day compressive strengths increased by 28.7%, 22.2%, 26.8%, and 22.9%, respectively. However, adding excessive amounts of more than 1% activated carbon had a minimal effect on the compressive strength or even decreased it, which agrees with other studies. Regarding the air contents of the mixtures, adding activated carbon decreased the air content from 3.6% to around 1.5%. The surface morphologies of fine aggregates and activated carbon particles were compared using a novel image processing technique. The results indicated that the surface of activated carbon significantly differs from that of aggregates.

• 한국지역사회생활과학회지
• /
• 제13권2호
• /
• pp.1-11
• /
• 2002

This study was conducted to estimate the amounts of the electromagnetic wave penetrating from a cellular phone in a pocket of dress shirt, as well as to test how different the penetration amounts were under the conditions of wearing. It was also investigated the possibilities that the amounts of the electromagnetic wave penetrating could be decreased by using twofold pocket or electromagnetic wave free fabric. The amounts of the electromagnetic wave penetrating were measured in the following five cases; one-layered pocket with 10 different fabrics as dress shirt, a pocket adding a layer of knitted cotton, two-layered pocket with same fabric as dress shirt, two-layered pocket adding a layer of knitted cotton, and one-layered pocket adding a layer of electromagnetic wave free fabric. Each of these five cases were measured using the front and back sides of a cellular phone facing to the body. The results were as follows; 1) The amounts of the electromagnetic wave penetrating were not significantly different in 10 different fabrics and were all above the caution range (0.02mW/$cm^2$). 2) The amounts of the electromagnetic wave penetrating in cases of the back side of the cellular phone to the body, were more than in cases of the front side. 3) There is a significantly differences in part on adding a knitted under wear to one and two layers of the pocket in the case of penetration amount under the wearing conditions. 4) The amounts of the electromagnetic wave penetrating in cases of adding a layer of electromagnetic wave free fabric, were close to the safe standard value of it. The above results suggested that facing the front side of cellular phone to the body and using extra layering with some electromagnetic wave free fabrics might have some protective effects again to the penetration amounts.

• KSBB Journal
• /
• 제11권2호
• /
• pp.125-131
• /
• 1996

Bacillus amyloliquefacieus 01용한 회분식 배양시 탄소원인 maltose와 glucose에서 저해제 acetic a acid, lactic acid가 세포성장과 생성물 생성에 미치 는 영향에 대해 검토한 결과, acetic acid가 저해제 로 작용함을 확인하였고, acetic acid 첨가시 초기농 도가 증가할수록 세포성장은 현저하게 감소되었다. ${\alpha}$-Amylase 생성 최대치는 maltose $10g/\ell$ 의 경우 a acetic acid 초기농도 $0.5g/\ell$ 일때 24시간 배양시에 l25unit/ml로 가장 높았고, glucose $10g/\ell$ 의 경우 acetic acid 초기놓도 $2.0g/\ell$ 일때 20시간 배양시에 331.55unit/ml로 가장 높았다. Acetic acid 초기농 도가 과량 일때는 세포의 성장이 최저 상태이고, ${\alpha}$-amylase 생성도 급격히 감소하였다. 저해제로 ace­t tic acid 첨가시 탄소원인 maltose와 glucose를 비 교하면 glucose에서 maltose 보다는 세포가 더 성장되었고, ${\alpha}$-amylase의 생성도 더 많게 나타났으며, 두 가지 탄소원에 다같이 저해 작용을 나타냈다.

• 분석과학
• /
• 제24권5호
• /
• pp.336-344
• /
• 2011

문화재 보존처리 시 사용되는 에폭시계수지에 플라스틱 첨가제 중 하나인 자외선 안정제를 첨가함으로써 수지의 광노화를 예방하는데 효과가 있는지 알아보고자 하였다. 문화재 접합 및 복원 과정에서 많이 사용되는 3가지 에폭시계수지에 HALS계와 UVA계 자외선 안정제를 농도별로 첨가하여 시편을 제작하였으며, 자외선 노화 실험을 실시하여 색도 변화, SEM 관찰, 접촉각, FT-IR 분석을 하였다. 또한 인장 전단 접착 강도 시험을 통해 자외선 안정제 첨가 유무에 따른 에폭시계수지의 물성 변화를 확인하였다. 분석 결과, 자외선 안정제를 첨가하여도 화학 구조상의 분해를 방지할 수 없지만 에폭시 R과 에폭시 A는 UVA계 자외선 안정제를 0.1% 이하 첨가함으로써 에폭시계수지의 접착 강도에 크게 영향을 미치지 않고 황변현상이나 균열과 같은 광노화로부터 최소화 할 수 있음을 확인하였다. 이를 통해 문화재접합 및 복원에 사용되는 에폭시계수지의 광노화 문제점을 보완하고 접합 및 복원재로서의 수명을 연장시킬 수 있을 것으로 기대된다.

• 한국응용과학기술학회지
• /
• 제17권2호
• /
• pp.139-143
• /
• 2000

There appeared enhancements of the conversion of methane by adding a small amount of CO in the aromatization reaction of methane using the Mo-zeolite catalyst. In case of adding $CO_{2}$, $CO_{2}$ changed to CO first, and then the conversion reaction occurred. It was observed by using isotopes as reactants that CO is related to the aromatization reaction of methane.