• The Journal of Korean Academy of Prosthodontics
• /
• v.47 no.4
• /
• pp.385-393
• /
• 2009

Statement of problem: High stress concentration on the crestal cortical bone has been regraded as a major etiologic factor jeopardizing long term stability of endosseous implants. Purpose: To investigate if the design characteristics of crestal module, i.e. internal type, external type, and submerged type, affect stress distribution on the crestal cortical bone. Material and methods: A cylindrical shaped implant, 4.3 mm in diameter and 10 mm in length, with 3 different crestal modules, i.e. internal type, external type, and submerged type, were analysed. An axisymmetric scheme was used for finite elment formulation. A vertical load of 50 N and an oblique load of 50N acting at $45^{\circ}$ with the implant's long axis was applied. The peak crestal bone stress acting at the intersection of implant and crestal bone was compared. Results: Under vertical load, the crestal bone stress was high in the order of internal, external, and submerged types. Under the oblique loading condition, it was in the order of internal, submerged, and external types. Conclusion: Crestal module design was found to affect the level of the crestal bone stresses although the actual amount was not significant.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.19 no.2
• /
• pp.249-263
• /
• 2017

The expansion behavior of inflatable steel pipe rockbolt shows geometric nonlinearity due to its ${\Omega}-shaped$ section. Previous studies on the anchoring behavior of inflatable steel pipe rockbolt were mainly performed using theoretical method. However, those studies oversimplified the actual behavior by assuming isotropic expansion of inflatable steel pipe rockbolt. In this study, the anchoring behavior of the inflatable steel pipe rockbolt were investigated by the numerical method considering the irregularity of pipe expansion and other influencing factors. The expansion of inflatable steel pipe rockbolt, the contact stress distribution and the change of the average contact stress and the contact area during installation were analyzed. The contact stresses were developed differently depending on the constitutive behavior of rocks. Small contact stresses occurred in steel pipes installed in elasto-plastic rock compared to steel pipes installed in elastic rock. Also, the anchoring behaviors of the inflatable steel pipe rockbolt were different according to the stiffness of the rock. The steel pipe was completely unfolded in the case of the stiffness smaller than 0.5 GPa, but it was not fully unfolded in the case of the stiffness larger than 0.5 GPa for the given analysis condition. When the steel pipe is completely unfolded, the contact stress increases as the rock stiffness increases. However, the contact stress decreases as the rock stiffness increases when the steel pipe is not fully expanded.

• The Journal of Sustainable Design and Educational Environment Research
• /
• v.17 no.2
• /
• pp.11-21
• /
• 2018

This study suggests desirable disaster safety education curriculum through analyzing the operational status of the school disaster safety management training course and demand survey of school staff. First, the problem of the disaster safety training course of the school is not connected with the lack of law and system and the school disaster safety job. Second, improvement of law and system and variety of training should be made to acquire professional knowledge. Third, it is necessary to divide curriculum into the following four categories, according to educational needs of public officials ; Educational administration officers course focused on facility safety, maintenance and disaster countermeasure. Educational officials in technical post course addressing approval and permission of school facility projects, seismic reinforcement of school building, etc. Educational supervisors course covering roles and responsibilities of the school safety supervisors in the event of disaster. Teaching staffs course focused on safety instructions for students. Fourth, it is found that lectures and experiential learning methods are the most desirable methods of teaching and learning, and the major ranks are earthquake disaster, fire, gas, typhoon, school road, and electrical safety.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.5
• /
• pp.1257-1269
• /
• 2010

The internet which is fast spread over all areas of our lives provides us with benefits of efficiency, productivity, and amusement; however, its features as an anonymous and non-face-to-face medium have raised a serious social issue of the collapse of internet ethics due to the abuse of it. Thereupon, the importance of internet ethics education has been highlighted to prevent side effects resulted from the internet and cultivate human-centered internet culture. In this paper, we suggests desirable methods for internet ethics education based on the investigation and analysis of the status of university freshmen's internet ethics. This research conducted a survey and analyzed its result after categorizing the status of internet ethics into the invasion of private information, invasion of intellectual property rights, harmful information, internet communication culture, cyber violence, internet addiction, and internet fraud. And based on the result of analyzing their internet ethics, this paper suggests desirable methods for internet ethics education. Next, internet ethics education was conducted by applying the proposed methods for internet ethics education, and its educational effect was evaluated. According to the result of verifying the educational effect measured statistically, it has proved that the suggested internet ethics education is effective to improve undergraduates' internet ethics.

• Resources Recycling
• /
• v.29 no.3
• /
• pp.11-23
• /
• 2020

This study aims to investigate breakage and liberation characteristics of iron ore from Shinyemi mine, Jeongseon by ball mill. Parameters of breakage functions for three grade samples of iron ore were obtained using single-sized-feed breakage test and back-calculation based on nonlinear programming. The results showed that with the increase in the grade of iron ore, the breakage rate factor decrease whereas the particle size sensitivity decreases. This results from retardation of microcrack-propagation by magnetite grain in the ore. Breakage distribution analysis showed that the breakage mechanism appear to be impact fracture dominant with the increase of grade owing to the stress distribution effect by magnetite grain. Degree of liberation (DOL) increased with the increase in grade and decrease in particle size, respectively. Using the breakage function and size-DOL relationship, a model that can predict time-dependent-DOL is established. When scale-up factors from operating condition are available, the model is expected to be capable of predicting size and DOL with time in actual mining process.

• Journal of Biosystems Engineering
• /
• v.26 no.5
• /
• pp.461-468
• /
• 2001

Impact between fruits and other materials is a major cause of product damage in harvesting and handling systems. The oriental pears are more susceptible to bruising than other fruits such as European pears and apples, and are required more careful handling. The interest in the handling of the pears for the processing systems has raised the question of the allowable drop height to which pears can be dropped without causing objectionable damage. Drop tests on pears were conducted using an impact device developed by authors to estimate the allowable drop height without bruising. The impact device was constructed to hold in a selected orientation and to release a fruit by vacuum for dropping on to a force transducer. The drop height was adjustable for zero to 60 cm to achieve the desired distance between the bottom of the fruits and the top of the impact force transducer. The transducer was secured to 150 kg$\sub$f/ concrete block. The transducer signal was sampled every 0.17 ms with a strain gage measurement board in the micro computer where it was digitaly stored for later analysis. The selected sample fruit was Niitaka cultivar of pears which is one of the most promising fruit for export in Korea. The pears were harvested during the 1998 harvest season from an orchard in Daejeon. The sample fruit was selected from two groups which were stored for 3 months and 5 months respectively by the method of current commercial practice. The pears were allowed to stabilize at environmental condition(18$^{\circ}C$, 65% rh) of the experimental room. One hundred fifty six pears were tested from the heights of 5, 7.5. 10 and 12.5 cm while measurement were made of impact peak force, contact time, time to peak force, dwell time, pear diameter and mass. The bioyield strength and modulus of elasticity were measured using UTM immediately after each drop test. The allowable drop height was estimated on the base of bioyield strength of the pears in two ways. One was assumed the peak force during impact test increasing linearly with time, and the other was based on the actual drop test results. The computer program was developed for measuring the impact characteristics of the pears and analyzing the data obtained in the study. The peak force increased while contact times decreased with increasing drop height and contact times of the sample from the hard tissue group. The allowable drop height increased with increasing bioyield strength and contact times, and also varied with Poisson\`s ratio, mass and equilibrium radius of the pears. The allowable drop height calculated by a theoretical method was in the range from 1 to 4 cm, meanwhile, the estimated drop height considering the result of the impact test was in the range from 1 to 6 cm. Since the physical properties of fruits affected significantly the allowable drop height, the physical properties of the fruits should be considered when estimating the allowable drop height.

• Journal of the Society of Disaster Information
• /
• v.13 no.4
• /
• pp.465-475
• /
• 2017

As a result of a survey on households using gas, gas safety accidents have been declining linearly in 2006. However, when analyzing the causes of gas accidents, accidents detail caused by carelessness have increased to 62%It is analyzed that urgent measures are needed. In addition, 7 households per 10 households perceive city gas as safe, but 30% of them recognize that gas safety accidents are likely to occur in their homes in the future. Even though city gas use is relatively safe,It is recognized that there is a risk. Although the perception of the gas safety of the city gas consumers is not related to the age and gender income level, it is analyzed that it is highly educated and experienced direct or indirect gas safety accident, the perception of safety was relatively low. In order to reduce gas safety accidents, the installation of gas safety equipment for elderly households should be continuously supplied. As a result of investigating the disposal costs in case of various disasters, 66% of the insurance costs were found to be highly dependent on insurance. In addition, to reduce gas safety accidents, the installation of gas safety devices for elderly households should be continuously implemented.

• Journal of Navigation and Port Research
• /
• v.33 no.1
• /
• pp.27-33
• /
• 2009

Estimation of the buckling and ultimate strength of a continuous stiffened plate subjected to combined transverse compression and lateral pressure is of high importance to ensure the safety of ship structures, particularly for the bottom plating under a deep draft condition For example, bottom plating of bulk carriers is subjected to transverse thrust caused by the bending of double bottom structure and the direct action of pressure on the side shells. Most of experimental tests, theoretical approach and numerical researches have been performed on the buckling and ultimate strength behaviour of plates or stiffened plates under combined compression and lateral pressure. With regard to stiffened panels, however, most of studies have been concerned with the load conditions of combined longitudinal thrust and lateral pressure, while fewer studies have been performed for the combined transverse thrust and lateral pressure. In addition, the previous researches are mainly concerned with an isolated rectangular plate simply supported along the all edges, whereas actual ship plating is continuous across the transverse frames and heavy girders. In the present paper, a series of elastoplastic large deflection FEA on a continuous stiffened plate is performed and then clarify the characteristic of collapse mode and explain the effect of transverse compression.

• 재활복지
• /
• v.21 no.1
• /
• pp.253-277
• /
• 2017

The purpose of this study was to develop the Constraints in Physical Activity Scale for people with physical Disabilities(CPASD) which measures the constraints in physical activity of people with physical disabilities. For this study, the 5 step analytic framework of unified validity developed by Messick (1995), the framework for conducting a strong program of construct validation by Benson (1998) method were applied. Furthermore, the validity of CPASD was systematically presented by applying common factor model and measurement model to 264 persons with physical disabilities. The conclusion based on the results and discussions of this study is as follows. First, CPASD presented evidence of job validity. Four factors (17 items) were developed, consisting of leader constraints, economic constraints, prejudice, and exercise environment constraints through the analysis of the factor structure and the fit of factor coefficients. Second, the factor structure of the developed CPASD (leader constraint, economic constraint, prejudice, exercise environment constraint) was statistically distinguished and stably reflected the existing exercise participation constraints theory. Third, the developed CPASD presented evidence of the validity of the criteria. Leader constraints and prejudice were negatively correlated with positive motor emotions, leader constraints, prejudice, and exercise environment constraints were positively correlated with negative motor emotions. Therefore, in future research, it is necessary to reevaluate the current system and actual condition related to leader constraints, economic constraints, prejudices, and exercise environment constraints derived as factors of CPASD. To do this, it is necessary to judge the degree of reality based on the causal relationship verification and IRT theory using CPASD.

• Korean Journal of Comparative Education
• /
• v.27 no.4
• /
• pp.231-254
• /
• 2017

The purpose of this study was to identify the actual condition and problems of Mongolian teacher quality management of selection and qualification and to recommend improvement. We examined the Mongolian teacher qualification management system with four criteria based on previous research. The results of this study are as follows. Mongolian government established quality management mechanisms such as selection of pre-service teachers, verification of teacher certificate, and appointment of in-service teachers, and teacher qualification standards. These Mongolian teacher selections and qualification systems were operated to attract the manpower required for teaching, to verify their qualifications and to induce professional development. However, the systems have not been able to verify the teachers' ability to practice in the field. We also found that the systems themselves were criticized for failing to guarantee conformity, fairness and transparency. Based on the results of this study, we discussed and draw policy implications for improvement of teacher quality management of selection and qualification in Mongolia.