• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2017년도 추계학술대회
• /
• pp.21-22
• /
• 2017

본 논문에서는 새로운 액티브 스너버 셀을 적용한 부스트 컨버터를 제안한다. 제안하는 컨버터의 메인 스위치는 ZVS 턴 온 및 오프, 보조회로 스위치는 ZCS 턴 온 및 ZVS 턴 오프하며 모든 다이오드는 ZCS 턴 오프를 성취한다. 또한, 제안하는 컨버터는 고전력 응용을 위한 인터리빙 기법으로 구현이 용이하다. 따라서 PWM 컨버터의 전력밀도와 효율을 높이고 EMI 노이즈를 줄일 수 있다. 제안하는 컨버터의 타당성을 검증하기 위해 600W/100kHz의 프로토 타입을 제작하여 실험을 진행하였다.

• Journal of Electrical Engineering and Technology
• /
• 제10권4호
• /
• pp.1566-1577
• /
• 2015

A novel high step-up converter is presented herein, which combines the conventional buck-boost converter, the charge pump capacitor and the coupling inductor. By doing so, a quite high voltage conversion ratio due to not only the turns ratio but also the duty cycle, so as to increase design feasibility. It is noted that the denominator of the voltage conversion ratio is the square of one minus duty cycle. Above all, there is no voltage spike across the switch due to the leakage inductance and hence no passive or active snubber is needed, and furthermore, the used switch is driven without isolation and hence the gate driving circuit is relatively simple, thereby upgrading the industrial application capability of this converter. In this paper, the basic operating principles and the associated mathematical deductions are firstly described in detail, and finally some experimental results are provided to demonstrate the effectiveness of the proposed high step-up converter.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1999년도 전력전자학술대회 논문집
• /
• pp.323-326
• /
• 1999

For decrease the harmonic current components of the power source, a first method is insert the choke coil that used the choke input type rectifier, the booster chopper circuit and buck chopper circuit. And the several method are studying like as the PWM(Pulse Width Modulation) converter and the active filter type which is used the high frequency switching and the sinusoidal wave formed input current. In this type, there are many problem as a low efficiency, increased the noise, the high leakage current and cost up by the high frequency switching. For improve this problems, the partial resonan method is used on the booster inducter and lossles snubber condenser. This method decreased the distortion factor has lower harmonic components than the hard switching and there is no switching loss by the ZCS(Zero Current Switching) at switch turn-on and the ZVS(Zero Voltage Swithcing) at switch turn-off

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 학술대회 논문집 전문대학교육위원
• /
• pp.166-170
• /
• 2003

This paper deals with the power loss analysis of voltage source type space voltage vector modulated soft switching inverter, and proposed the new voltage vector correction principle during one sampling period on realize high quality cutput voltage waveforms for two soft-swiching approches. The operating pinciple of a single active auxiliary resonant DC link snubber circuit is described. Moreover, the effectiveness of soft switching inverter operating under the corrected voltage pattern is proved on the basis of simulation and experimental results.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 추계학술대회 논문집
• /
• pp.149-153
• /
• 2003

In this paper, the design and implementation of a high power(300W) forward converter using a planar transformer is presented. The overall size and volume of the converter is decreased by replacing a planar transformer in stead of using a conventional winding transformer. Due to the decreased size and volume, power density of the applied forward converter is increased. Also, in this paper, the 300W ZVS forward converter with active clamp snubber circuit is compared to the 300W hard switching forward converter.

• Journal of Power Electronics
• /
• 제6권1호
• /
• pp.1-7
• /
• 2006

This paper is a record of the study on a high efficiency and high power chopper based on the new soft switching method QRAS (Quasi~resonant Regenerating Active Snubber) designed for a Fuel Cell Electric Vehicle (FCEV). This power chopper is basically proposed for 25kHz soft switching. To confirm the practicality and effectiveness of the converter, the fabrication of a prototype-model using IGBTs was completed. Additionally, a 8kW rating test, a light load test, a current discontinuous mode test and a stable operation resonance test was completed. The circuit geometry, the basic operation, and the 8kW one-tenth-prototype test results are reported with a $97.5\%$ efficiency measurement.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2018년도 전력전자학술대회
• /
• pp.21-23
• /
• 2018

본 논문에서는 능동형 스너버를 사용한 비대칭 하프-브리지 컨버터를 제안한다. 비대칭 하프-브리지 컨버터는 홀드-업 시간을 고려하여 넓은 입력전압 범위에서 설계되면, 노미널 동작 시 작은 시비율로 동작하여 변압기에 큰 오프셋 전류가 발생한다. 또한 변압기가 작은 턴 비로 설계되어 1차측 전류 스트레스와 2차측 정류기의 전압 스트레스가 커지는 문제점이 있다. 이러한 문제점들을 해결하기 위해, 제안하는 컨버터에서는 추가 스위치를 사용해 추가적인 전압이득을 얻음으로써, 홀드-업동작 시 낮아지는 입력 전압을 보상한다. 때문에 제안하는 컨버터는 홀드-업 상태를 고려하지 않고 설계될 수 있어, 노미널 시에 큰 시비율로 동작한다. 게다가 추가 스위치는 능동형 스너버로 사용되어 2차측 정류기 다이오드의 전압 링잉을 제거하여 전압 스트레스를 저감시킨다. 이와 같은 특징으로 인하여 제안하는 컨버터는 전 부하 영역에서 높은 효율을 갖는다. 제안하는 컨버터의 효용성을 검증하기 위해 320-410V 입력전압과 19.5V/200W 출력에서 실험이 진행되었다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2017년도 전력전자학술대회
• /
• pp.237-239
• /
• 2017

The isolated boost DC-DC converter based on three switches in fuel cell applications is presented in this paper. The major advantages of the proposed converter are as follows: continuous input current; decrease one active switch and no use snubber circuit. The operating principles and analysis of the proposed converter have been discussed. A 400 W prototype has been tested in the laboratory to verify the performance of the proposed converter and a PID controller was used to clarify the DC output voltage at 400 V. The simulation and experimental results are shown to validate the theoretical analysis.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2015년도 전력전자학술대회 논문집
• /
• pp.171-172
• /
• 2015

용접기는 3상 교류 입력을 받아 정류기를 거쳐 DC/DC 컨버터를 통하여 저전압, 대전류의 출력을 이용하여 금속 재료를 용접한다. 기존의 용접기는 대용량 시스템으로 IGBT를 이용하여 주파수가 낮은 범위에서 사용되므로 변압기 등 시스템 크기가 매우 크다. 본 논문에서는 고주파화를 통하여 용접기의 크기를 줄이는 것이 목적으로 용접기의 구성 중 브리지 다이오드로 구성된 간단한 구조인 입력 AC/DC부를 제외한 인버터, 변압기, 정류기, 출력 인덕터를 포함하는 DC/DC 컨버터를 설계하고 실험 검증하였다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2015년도 전력전자학술대회 논문집
• /
• pp.357-358
• /
• 2015

This paper provides a comparison of power converter loss and thermal description for voltage source and current source type 5MW-class medium voltage topologies of wind turbines. Neutral-point clamped three-level converter is adopted for voltage source type topology while two-level converter is employed for current source type topology considering the popularity in the industry. In order to match the required voltage level of 4160V with the same switching device of IGCT as in voltage source converter, two active switches are connected in series for the case of current source converter. The loss analysis is confirmed through PLECS simulations. In addition, the loss factors due to di/dt and dv/dt snubber and ac input filter are presented. The comparison result shows that VSC-based wind turbine system has a higher efficiency than that of CSC under the rated operating conditions.