• 조명전기설비학회논문지
• /
• 제14권4호
• /
• pp.8-15
• /
• 2000

본 논문에서는 F 컨버터의 능동형 PFC 시스템을 구성하고, 진력 변환시 입력 전류를 전원 전압과 동장연 정현파로 제이하는 동시에 출력 전압에 포함되는 고조파 등의 잡음을 제거하고 직류 출력 전압을 제어하기 위한 PWM-PFM 제어 기법을 제시하였다. 부하단에서 필요한 전압과 높은 전력 효율을 얻기 위하여 인버터 단계애서 전류 성형 제어를 실행한 후, 순방­향(forward) 컨버터에 의해 다시 직류 전압으로 변환시켜 부하단으로 출력한다. 입력 전압이 30[V]이교 승압 (boost) 인덕터가 1.1[mH]일 때 정격 출력은 전압 50[V], 전류1[A], 듀티비 0.5 이상으로 하여 부하 처항에 따른 전압 변화를 PWM-PFM 제어 기법을 이용하며 제어하였고, 전류 성형 기법을 이용하여 0.93획 역률로 고조파를 감쇠 및 개선하였다.

• Journal of Power Electronics
• /
• 제19권4호
• /
• pp.858-868
• /
• 2019

With the widespread use of modern clean energy, lithium-ion batteries have become essential as a more reliable energy storage component in the energy Internet. However, due to the difference in monomers, some of the battery over-charge or over-discharge in battery packs restrict their use. Therefore, a novel multiphase interleaved converter for reducing the inconsistencies of the individual cells in a battery pack is proposed in this paper. Based on the multiphase converter branches connected to each lithium battery, this circuit realizes energy transferred from any cell(s) to any other cell(s) complementarily. This flexible interlaced converter is composed of an improved bi-directional Buck-Boost circuit that is presented with its own available control method. A simulation model based on the PNGV model of fundamental equalization is built with four cells in PSIM. Simulation and experimental results demonstrate that converter and its control achieve simple and fast equalization. Furthermore, a comparison of traditional methods and the HNFABC equalization is provided to show the performance of the converter and the control of lithium-based battery stacks.

• 전력전자학회논문지
• /
• 제16권3호
• /
• pp.242-249
• /
• 2011

제안하는 컨버터는 부스트 하프브리지-전압 더블러를 각각 병렬-직렬로 연결하여 출력전력 및 출력전압을 증대시키므로 고승압 대전력 응용에서 소자의 선정이 용이하다. 특히 고주파변압기 턴 비를 작게 할 수 있고 DC 오프셋이 제거되어 최적의 변압기 설계가 가능하며, 3개의 코아로 전력이 분배되어 Low Profile 및 열 분산에 유리하다. 제안하는 컨버터는 전 영역(0 ∼ 1)의 듀티 사용으로 스타트업 및 추가의 클램프회로가 필요 없으며 입력전압 변동이 큰 응용에 적합하다. 또한 넓은 듀티영역에서 스위치의 ZVS 턴온과 다이오드의 ZCS 턴온 턴오프가 성취되므로 고효율을 달성할 수 있다. 제안하는 컨버터를 5 kW급 시작품으로 검증하였다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2011년도 추계학술대회
• /
• pp.44-45
• /
• 2011

Research on photovoltaic (PV) generation is taking a lot of attention due to its infinity and environment-friendliness with decrease of price per PV cell. While central inverters connect group of PV modules to utility grid in which maximum power point tracking (MPPT) for each module is difficult, micro inverter is attached on each module so that MPPT for individual modules can be easily achieved. Moreover, energy generation and consumption efficiency can be much improved by employing direct current (DC) distribution system. In this paper, a digitally controlled PV micro converter interfacing PV to DC distribution system is proposed. Boundary conduction mode (BCM) is utilized to achieve zero voltage switching (ZVS) of active switch and eliminate reverse recovery problem of passive switch. A 120W prototype boost PV micro converter is implemented to verify the feasibility and experimental results show higher than 98% efficiency at peak power and 97.29% of European efficiency.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2000년도 전력전자학술대회 논문집
• /
• pp.665-669
• /
• 2000

Recently the problem of energy branch become worse increasingly. Therefore many researches about new energy source are processing in several places around are processing in several places around the world. Especially solar energy has many advantages like as purity and infinity. Photovoltaic(PV) system can be classified into two types : One is stand alone type and the other is utility interactive one. Utility interactive type PV system need some technology that Maximum peak power tracking(MPPT) and Anti-islanding and Active Power filter(APF). For APF operation dc-link voltage should be high to supply sufficient output current which needed for harmonic current compensation so usually DC-DC converter is used for boost. In this paper DC-DC converter for PV system and controller for dc-link voltage control are analyzed and designed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 B
• /
• pp.1214-1216
• /
• 2004

Conventional Switched Mode Power Supplies(SMPS) with diode-capacitor rectifier have distorted input current waveform with high harmonic contents. Typically, these SMPS have a power factor lower than 0,65. To improve with this problem the power factor correction(PFC) circuit of power supplies has to be introduced. PFC circuit have tendency to be applied in new power supply designs. The input active power factor correction circuits can be implemented using either the two-stage or the single-stage approach. In this paper, the comparative analysis of power factor correction circuit using feedforward control with average current mode single-stage flyback method converter and two-stage converter which is combination of boost and flyback converter. The two prototypes of 50W were designed and tested a laboratory experimental. Also, the comparative analysis is confirmed by simulation and experimental results.

• 조명전기설비학회논문지
• /
• 제29권5호
• /
• pp.57-64
• /
• 2015

This paper proposes a new switching algorithm for an controllable clamp snubber to improve the efficiency of a fly-back converter system. This system uses an controllable clamp method for the snubber circuit for the efficiency and reliability of the system. However, the active clamp snubber circuit has the disadvantage that system efficiency is decreased by switch operating time because of heat loss in resonance between the snubber capacitor and leakage inductance. To address this, this paper proposes a new switching algorithm. The proposed algorithm is a technique to reduce power consumption by reducing the resonance of the snubber switch operation time. Also, the snubber switch is operated at zero voltage switching by turning on the snubber switch before main switch turn-off. Experimental results are presented to show the validity of the proposed controllable clamp control algorithm.

• 전기전자학회논문지
• /
• 제20권1호
• /
• pp.45-53
• /
• 2016

본 논문에서는 진동에너지 수확을 위한 MPPT (Maximum Power Point Tracking) 제어 기능을 갖는 CMOS 인터페이스 회로를 설계하였다. 간단한 구조와 적은 비용으로 출력을 안정화시키기 위해 전력변환기인 DC-DC 부스트 변환기의 출력 단에 PMU (Power Management Unit)를 이용하는 구조를 제안하였다. 또한, 진동소자로부터 최대전력을 수확하여 시스템의 효율을 향상시키기 위해 FOC (Fractional Open Circuit) 방식의 MPPT 제어회로를 설계하였다. 진동소자 (PZT)에서 출력되는 AC 신호는 AC-DC 변환기를 통해 DC 신호로 변환되며, DC-DC 부스트 변환기를 거쳐 승압되고, PMU에 의해 듀티 (duty)를 갖는 안정화된 신호로 변환되어 부하로 공급된다. AC-DC 변환기는 효율 특성이 좋은 능동 다이오드를 이용한 전파정류기를 사용하였으며, DC-DC 부스트 변환기는 제어회로가 간단한 쇼트키 다이오드를 이용한 구조를 사용하였다. 제안된 회로는 $0.35{\mu}m$ CMOS 공정으로 설계되었으며, 설계된 칩의 면적은 $915{\mu}m{\times}895{\mu}m$이다. 설계된 회로의 성능을 검증한 결과 전체회로의 최대 전력효율은 83.4%이다.

• Journal of information and communication convergence engineering
• /
• 제15권1호
• /
• pp.62-71
• /
• 2017

This paper presents a low-power voltage converter based on a reconfigurable capacitor array. Its energy recycling capacitor array stores the energy during a charge stage and supplies the voltage during an energy recycle stage even after the power source is disconnected. The converter reconfigures the capacitor array step-wise to boost the lost voltage level during the energy recycle stage. Its energy saving is particularly effective when most of the energy remaining in the charge capacitors is wasted by the leakage current during a longer sleep period. Simulations have been conducted using a voltage source of 500 mV to supply a $V_{DD}$ of around 800 mV to a load circuit consisting of four 32-bit adders in a 65-nm CMOS process. Results demonstrate energy recycling efficiency of 85.86% and overall energy saving of 40.14% compared to a conventional converter, when the load circuit is shortly active followed by a long sleep period.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.993-997
• /
• 1998

This paper presents a two-switch boost chopper with a sinewave current shaping and power factor correction scheme, which is applied for driving electronic ballast using high frequency resonant inverter. A working principle of the proposed one-converter type electronic ballast with power factor correction and active filtering schemes is described on the bases of the equivalent circuit of each operation mode, together with operation analysis. The steady-state performance evaluations of this electronic ballast are illustrated and discussed in experiment.