• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.6
• /
• pp.479-486
• /
• 2019

The fully digital active array radar uses a wide beam for effective mission performance within a limited time. This paper presents a convex optimization algorithm that adjusts only the phase of an array element. First, the algorithm applies a semidefinite relaxation technique to relax the constraint and convert it to a convex set. Then, the constraint is set so that the amplitude is fixed to some extent and the phase is variable. Finally, the optimization is performed to minimize the sum of the eigenvalues obtained through eigenvalue decomposition. Compared to the application results of the existing genetic algorithm, the proposed algorithm is more effective in wide beam design for a fully digital active array radar.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.5
• /
• pp.162-170
• /
• 2022

In this paper, the phased-array transceiver (TRX) channel amplitude and phase calibration method for a radar wind profiler (RWP) based on the 256 active phased array is discussed. Without the additional module, the TX and RX calibration paths were secured using couplers and switches in the TRX front ends and the TRX switching duplexers, and the amplitude and phase of the 256 TRX were calibrated using a gain and phase detector. The beam widths and side lobes of five beams (vertical, east, west, south, and north) of the calibrated 256 active phased array antenna were confirmed by a near-field which agreed well with the simulation results. The proposed calibration method can be easily applied to a system based on an active phased array operated in an outdoor environment.

• Journal of electromagnetic engineering and science
• /
• v.10 no.4
• /
• pp.309-315
• /
• 2010

A dual-band dual-polarized microstrip antenna array for an advanced multi-function radio function concept (AMRFC) radar application operating at S and X-bands is proposed. Two stacked planar arrays with three different thin substrates (RT/Duroid 5880 substrates with $\varepsilon_r$=2.2 and three different thicknesses of 0.253 mm, 0.508 mm and 0.762 mm) are integrated to provide simultaneous operation at S band (3~3.3 GHz) and X band (9~11 GHz). To allow similar scan ranges for both bands, the S-band elements are selected as perforated patches to enable the placement of the X-band elements within them. Square patches are used as the radiating elements for the X-band. Good agreement exists between the simulated and the measured results. The measured impedance bandwidth (VSWR$\leq$2) of the prototype array reaches 9.5 % and 25 % for the S- and X-bands, respectively. The measured isolation between the two orthogonal polarizations for both bands is better than 15 dB. The measured cross-polarization level is ${\leq}-21$ dB for the S-band and ${\leq}-20$ dB for the X-band.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.5
• /
• pp.568-573
• /
• 2019

Modern Radars are evolving into MFRs which can search multiple targets simultaneously and then track them. Additionally they should be able to avoid some external jamming signals. Applying to these MFRs, Antennas should be able to perform DBF including to not only real-time beam steering but also multi-beam forming simultaneously. And they can cancel the beam at the specific direction. In this paper, we describe the implementation of sub-array type antenna hardware which can be applying DBF. Also we propose the modified amplitude aperture distribution for suppressing the side lobe level and explain the sub-array receiver design with amplitude tapering. It consists in making the amplitude weighting in 2 steps. In order to compare two weighting cases, we investigate the G/T performance for the array antenna. At the conclusion, we make a comparative study for the dynamic range of every sub-array receiver and present the hardware implementation that is more advantageous for sub-array alignment and calibration in DBF.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.12
• /
• pp.924-934
• /
• 2018

This paper describes the development and measurement results of C-band planar active phase array antenna for detecting and tracking radar(weapon-locating radar). The antenna is designed with 14 sub-arrays(12 main channels and 2 sidelobe blanking channels and approximately 3,000 elements of transmit-receive channel) to generate transmit and digital receive patterns. Using a near-field measurements facility, G/N, transmit patterns, and received patterns are measured. Receive patterns are implemented with digital beamforming by signal processing. The measurement results demonstrate that antenna design specifications were fulfilled.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.15 no.6
• /
• pp.812-819
• /
• 2012

Interference and jamming are becoming increasing concern to a radar system nowdays. AESA(Active Electronically Steered Array) antennas and adaptive beamforming(ABF), in which antenna beam patterns can be modified to reject the interference, offer a potential solution to overcome the problems encountered. In this paper, we've developed a planar active phased array radar system, in which ABF, target detection and tracking algorithm operate in real-time. For the high output power and the low noise figure of the antenna, we've designed the S-band TRMs based on GaN HEMT. For real-time processing, we've used wavelenth division multiplexing technique on fiber optic communication which enables rapid data communication between the antenna and the signal processor. Also, we've implemented the HW and SW architecture of Real-time Signal Processor(RSP) for adaptive beamforming that uses SMI(Sample Matrix Inversion) technique based on MVDR(Minimum Variance Distortionless Response). The performance of this radar system has been verified by near-field and far-field tests.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.1
• /
• pp.52-59
• /
• 2009

In modern radars, dynamic range requirements far severed due to high CNR(Clutter-to-Noise Ratio) environment operation scenario. ADC spurious signal restricted the required dynamic range. In this paper, receiver gain of active phased array radar dependent on ADC nonlinear characteristic was analyzed. Within limited scope of ADC SFDR which blocks required system dynamic range, ADC dynamic range reaches trade-off with ADC SNR loss. Comparing antenna stage output noise voltage to that of ADC input, receiver gain was mathematically analyzed. Finally the whole contents were explained from the application example.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.12
• /
• pp.1335-1342
• /
• 2010

This paper presents design and measurement result of S-band, $\bigcirc$ kW solid-state transmitter and receiver for active array radar system. Transmitter characteristics show 63 dB gain, 200 usec pulse width(max.), 10 % duty(max.) and 63 dB pulse to pulse stability. Receiver characteristics show 23 dB gain and 3.2 dB noise figure. Receiving mode for pulse network analyzer is used for pulse to pulse stability measurement. Measurement results satisfies all specification.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.1
• /
• pp.61-68
• /
• 2018

In this paper, we described about methods and results to verify the Tx/Rx beam characteristics of a planar active phased array antenna as using a near-field measurement. The near-field system can effectively measure multiple beams and predict the performance degradation due to the partial failure of individual elements. Also, it can accurately predict the EIRP relating to detection performance of the active phased array radar. We briefly described the near-field measurement method to verify the Tx/Rx beam characteristics, and then verified the effectiveness of measurement method by analyzing the measured results.

• Journal of electromagnetic engineering and science
• /
• v.19 no.2
• /
• pp.107-114
• /
• 2019

Alert-confirm detection is a highly efficient method to improve phased array radar search performance. It comprises sequential detection in two steps: alert detection, in which a target is detected at a low detection threshold, and confirm detection, which is triggered by alert detection with a longer dwell time to minimize false alarms. This paper provides a design method for applying the alert-confirm detection to multifunctional radars. We find optimum dwell times and false alarm probabilities for each alert detection and confirm detection under the dual constraints of total false alarm probability and maximum allowable dwell time per position. These optimum values are expressed as a function of the mean new target appearance rate. The proposed alert-confirm detection increases the maximum detection range even with a shorter frame time than that of uniform scanning.