• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3389-3394
• /
• 2007

Characteristics of heat transfer and pressure drops of fills for solar tower volumetric air receivers are experimentally investigated with the material and the thickness. The volumetric air receiver considered in this paper consists of a ceramic tube and fills are inserted in the ceramic tube. Air is used as the working fluid. Two materials, which are a honeycomb(diameter: 100mm, thickness: 30mm) and laminated mesh(diameter: 100mm, thickness: 1mm), are considered as the fills. In order to investigate the characteristics of heat transfer of fills, this volumetric air receiver is heated by an electric heater and air temperatures in ceramic tube are measured. Also, the radiative shields are installed to measure the only air temperature. In addition, the pressure losses are measured with the thickness of fills while the air goes through the fills inserted in an acrylic tube. The flow becomes turbulent and fully developed in front of the fills. The results show that the heat transfer and pressure drop characteristics of the laminated mesh are superior to those of the honeycomb.

• The korean journal of orthodontics
• /
• v.24 no.3 s.46
• /
• pp.709-719
• /
• 1994

The aim of this investigation was to identify which suing is more suitable for uprighting of the 30 degree inclined lower second molar in different situations. Between four different molar uprighting springs which were A, B, C type and T-loop spring, the author tested T-loop suing as a control material and the other springs were experimental group. Each spring was fabricated from .017' $\times$ .025' TMA wire and preactivated with 40 degree tip-back bend. Stabilizing unit included from the lower right central incisor to the lower right second premolar which were made by acrylic resin. The photoelastic overview of the lower right quadrant showed that stress concentrations were observed in its photoelastic model. The obtained results were as follows. 1. Higher concentration of compression can be seen clearly at the distal curvature than the mesial of the lower second molar when A type uprighting spring was applied, which can be used as a space regainer. 2. Higher level compression was presented at the mesial root apex area than the distal of the lower second molar in B type uprighting spring, which can be used as a space closer. 3. Areas of higher compression and tension were observed about the mesial and distal root of the lower second moalr than A and B type in C type uprighting spring, which can be used as a partial space regainer.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.05a
• /
• pp.215-225
• /
• 2002

In order to enhance the thermal stability of binder materials of bonded type solid lubricants, several combinations of metal-alkoxide based sol-gel materials such as methyltrimethoxysilane(MTMOS), $titaniumisopropoxide(Ti(Opr^{j})_{4})$, $zirconiumisopropoxide(Zr(Opr^{j})_{4})$ and $aluminumbutoxide(Al(Obu^{t})_{4})$ were chemically modified by epoxy-, acrylic- and fluoro-silane compounds, respectively, in this work. Friction and wear characteristics of these hybrid ceramic materials were tested with a micro tribe-tester where a reciprocating steel ball slid on a test material, and the tribological property was also evaluated with respect to both heat-curing temperature and tile time. Test results generally showed that hybrid ceramic materials modified by epoxy-silane compounds had a low friction compared to others. And the higher heat-curing temperature and the longer heat treatment time resulted in the higher friction and the lower wear. IR spectroscopic analyses revealed that it was caused mainly by the increased metal oxide content in hybrid ceramics when the heat-curing temperature was over $320^{\circ}C$.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.11 no.5
• /
• pp.93-102
• /
• 1997

In order tl get Maaterial requirements for the Improviment of erliability of Insulatint materials for power cables, partial discharge characteristics of Polyethylenes were measured by an ultrasonic techjique and Measured signals were processed to cbtain the paraceters useful for thr quantification of partial discharge characteristics of polyethylenes. This technique was applied to obtain material requirements for the development of improved insulating materials for power cables,As a result, it was found that partial discharging activities in polyethylenes were suppressed considerably when p proper amount of acrylic acid, 0.003[wt %]in this particular case, is grafted on polyethylene chains.It can be concludid from the present study that partial discharging actibities in polyethylenes could be suppressed by the modification of polyethylene with proper chemical components, acrilic acid in this particular study.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.19 no.4
• /
• pp.383-394
• /
• 1997

This study was done to examine adherence of oral bacteria to titanium dental implant and to know the effective prophylactic antibiotics using an in vivo model. Three samples each of the implant material were set in an acrylic resin flange and placed in the maxillary buccal sulcus of twenty volunteers. At 6- and 54-hour intervals, each sample was placed on blood agar plate (BAP) and chocolate agar, and then they were incubated and identified. Also antibiotic susceptibility test was performed. The results obtained mere as follows ; 1. The microorganisms were chain-like Gram positive cocci and staphyline Gram positive cocci, Gram positive bacilli in order of frequency were found at 6-hour and 54-hour samples by Gram staining. 2. Streptococci was found predominantly at both 6-hour and 54-hour samples, but number of streptococci was decreased as compared to 6-hour samples. 3. There was no difference in the bacterial species adherent to implant between 6-hour and 54-hour samples. 4. All the microbes were sensitive to AMC (amoxacillin clavulanic acid), chloramphenicol, quinolone and vancomycin in the antibiotic susceptibility test. Above results suggest that streptococcus are mainly adhered to titanium implant after implant was placed in the oral cavity and AMC is the most recommendable antibiotics to prevent the peri-implant inflammation.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.607-614
• /
• 2010

Shear behavior of granular soils largely affects the safety and stability of underground and earth structures. This study presents the characteristics of shear zone in a direct shear test using shear wave and electrical resistivity measurements. An innovative direct shear box made of transparent acrylic material has been developed to prevent direct electric current. Bender elements and electrical resistivity probe are embedded in the wall of direct shear box to estimate the shear wave velocities and the electrical resistivity at the shear and non-shear zones. Experimental results show that the void ratio and shear wave velocity at shear zone increase during shearing while the values remain constant at non-shear zone. The results demonstrate correlation among the contact force, small strain shear modulus, and void ratio at shear zone. This study suggests that the application of the modified direct shear box including shear wave and electrical resistivity measurements may become an effective tool for analyzing soil behavior at shear zone.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.2
• /
• pp.140-146
• /
• 2014

Stenosis is the drastic reduction in the cross-sectional area of blood vessel caused by accumulations of cholesterol. It affects the blood flow property and structure from the fluid dynamic point of view. To understand the flow phenomenon more clearly, a particle image velocimetry method is used and the fluid dynamic characteristics in a circular channel containing stenosis structure is investigated experimentally in this study. Different stenotic-structured models made of acrylic material are subjected to a pulsatile flow generated by an in-house designed pulsatile pump. The inner diameter of the tube inlet is 20 mm and the length of reduced area for stenosis ranges between 35mm and 40mm. It is circulated continuously through a circular channel by the pump system. Pressure is measured at four different sections during systolic and diastolic phase changes. The phase-averaged velocity field distribution shows a recirculation regime after the stenotic structure. The effects of the stenotic obstructions are found to be more severe when the aspect ratio is varied.

• Design & Manufacturing
• /
• v.9 no.3
• /
• pp.14-18
• /
• 2015

Although demand for non-metalic materials, acrylic and metal plate material is increased. The complex processing equipment that can machine it at the same time is extremely limited. In case of existing manual multiple routers, it is no substantial demand due to the difficulty in use and low efficiency. In this study, the CNC multiple router was designed. The structural analysis was carried out according to the structure of the bed as a basic step for the development of multiple CNC router system that can guarantee the increase in yield while optimizing the manufacturing process. CNC router added a dummy was carried out about weight analysis and load analysis. Development of a CNC router system will be progressed on the basis of the analysis result.

• Journal of the Korea Furniture Society
• /
• v.23 no.3
• /
• pp.229-241
• /
• 2012

Kuramata Shiro's design has been evaluated as an unseen type of beauty. He created totally different aesthetics from functional furniture by utilizing glass, acrylic, and expanded steel mesh which usually are inappropriate for making furniture. Kuramata told that his design always starts from zero status. By doing so, he could be free from the existing notion and form of furniture. This means that every function and every form must be based on his own understanding and experiment in order to produce newness. Owing to these efforts, we can regard his design as artworks. Kuramata tried to bring forth formative lines inside contour of furniture rather than to deform only the formal outlines of furniture. These lines are very delicate and sometimes ephemeral. But they establish formal potentiality of phenomenological being of beauty. Also those lines are built from humble industrial material but they open the truth of thing itself and introduce the beauty to field of aletheia. At the same time, transcending limitation of function and use, they leave pure form and temporariness. So, lines become a field of Heideggerian rift which produces embodiment of form. We can appreciate his design through these lines that are relatively thin but vivid enough to follow his original world of art.

• Transactions of the Korean hydrogen and new energy society
• /
• v.15 no.2
• /
• pp.166-174
• /
• 2004

Purple non-sulfur bacteria, Rhodobacter sphaeroides KD131 grew to reach the maximum cell concentration in 45 hrs of incubation in the synthetic media containing (NH4)2SO4, L-aspartic acid and succinic acid as the carbon and nitrogen sources, respectively, at 30oC under 8 klux irradiance using halogen lamp. The strain produced hydrogen from the middle of the logarithmic growth phase and continued until the cell growth leveled out. The strain grew and produced hydrogen under the irradiance of 3-30 klux, but cell growth was inhibited over 100 klux. In addition, anaerobic/light culture condition was better than the aerobic/dark on the hydrogen production. Among various photo-bioreactors examined, the flat-vertical reactor manufactured using clear acrylic plastic material showed the best hydrogen production rate at the given culture condition.