• The Journal of the Acoustical Society of Korea
• /
• v.31 no.7
• /
• pp.480-486
• /
• 2012

In the design of electro acoustic transducer, power factor improvement circuit is more required rather than impedance matching if the driving power amplifier has little inner resistance. Many research results have been focused on the power matching circuit designing for transferring maximum power in the wideband. There are few results in the designing study on the power factor improvement for the wide band electro acoustic transducer. In this paper, we propose a new design method on the power factor improvement for the wide band electro acoustic transducer. The proposed method consists of two steps, the chebyschev matching method and the constrained optimization, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38B no.12
• /
• pp.967-975
• /
• 2013

In the design of underwater electro acoustic transducer, power factor improvement circuit is more required rather than impedance matching if the driving power amplifier has little inner resistance. Many research results have been focused on the power matching circuit designing for transferring maximum power in the wideband. There are few results in the designing study on the power factor improvement for the wide band underwater electro acoustic transducer. In this paper, we set up a new design method on the power factor improvement for the wide band electro acoustic transducer, and confirm its feasibility by the experiments.

• Wind and Structures
• /
• v.23 no.2
• /
• pp.91-107
• /
• 2016

Flow-excited acoustic resonance in ducted cavities can produce high levels of acoustic pressure that may lead to severe damage. This occurs when the flow instability over the cavity mouth, which is created by the free shear layer separation at the upstream edge, is coupled with one of the acoustic modes in the accommodating enclosure. Acoustic resonance can cause high amplitude fluctuating acoustic loads in and near the cavity. Such acoustic loads could cause damage in sensitive applications such as aircraft weapon bays. Therefore, the suppression and mitigation of these resonances are very important. Much of the work done in the past focused on the fluid-dynamic oscillation mechanism or suppressing the resonance by altering the edge condition at the shear layer separation. However, the effect of the downstream edge has received much less attention. This paper considers the effect of the impingement edge geometry on the acoustic resonance excitation and Strouhal number values of the flow instabilities in a ducted shallow cavity with an aspect ratio of 1.0. Several edges, including chamfered edges with different angles and round edges with different radii, were investigated. In addition, some downstream edges that have never been studied before, such as saw-tooth edges, spanwise cylinders, higher and lower steps, and straight and delta spoilers, are investigated. The experiments are conducted in an open-loop wind tunnel that can generate flows with a Mach number up to 0.45. The study shows that when some edge geometries, such as lower steps, chamfered, round, and saw-tooth edges, are installed downstream, they demonstrate a promising reduction in the acoustic resonance. On the other hand, higher steps and straight spoilers resulted in intensifying the acoustic resonance. In addition, the effect of edge geometry on the Strouhal number is presented.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.3
• /
• pp.409-415
• /
• 2008

This paper proposed a new optimal design method of the electronic ballast with stable run-up current for Metal Halide lamp during the ignition condition. In order to avoid operation in the acoustic resonance frequency band and to supply the optimal ignition current without demage of inverter switching components during the ignition period, the values of the series inductor Ls, the series capacitor Cs, and the parallel capacitor Cp were determined by analysis of characteristics of inverter transfer function depend on Lamp operating power and resistance of ignition condition and steady state operating condition. For the prototype ballast for a 400W Metal Halide Lamp, experimental results are presented in order to validate the proposed method.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.851-852
• /
• 2006

This paper presents methods to reduce acoustic noise in interior permanent magnet (IPM) motor. Mechanical and magnetic sources are considered to reduce noise of the machine, and structural and electromagnetic designs are performed. In the structural design to reduce mechanical source, the structural resonances are moved to higher frequency for enhancement of stiffness. Then, the electromagnetic design to reduce magnetic source, the amplitudes of magnetic force harmonics are reduced by using objective function of response surface methodology (RSM). The validity of the design process and objective functions is confirmed with their calculated and experimental results.

• The Journal of the Acoustical Society of Korea
• /
• v.11 no.2
• /
• pp.59-67
• /
• 1992

Recently, the problem which actively control the unwanted noise propagated from the technical structure by the generated secondary sound has become considerable topic from the environmental preservation point of view. In most of these studies, active noise control deals with a plane wave propagation at low frequency using adaptive filtering techniques. On the other hand, in real acoustic systems are mostly short due to the limitation of geometric configuration. In this case, the acoustic properties such as reflections and resonances inside the acoustic system should be considered. In this paper, the acoustic modeling method for short length duct was introduced using the transfer matrix method, and the active noise control problem was investigated with \implementation of FIR filter for the transfer function of control system derived from this modeling method. The identification methods for the acoustic model of actual control system was proposed by numerical computation technique based on the estimation of optimal FIR filter coefficients. The acceptable attenuation on the real acoustic system and stability of the controller are predicted in this computational simulation.

• The Journal of the Acoustical Society of Korea
• /
• v.15 no.6
• /
• pp.52-58
• /
• 1996

Using the acoustic resonances and oscillatory pulsations considered as the branch of wave technologies, the concept of the acoustic resonance diffusers for waste water treatment which maximize the oxygen transfer efficiency in gas-liquid two phase medium have been proposed, and studies for the principles and performance tests were accomplished. Besides, the design concepts for the low pressure Helmholtz resonator, cylinder and annular type reflection resonator and combined type resonance system have been implemented. The acoustic resonance energy which can speed up the mass transfer process increase the oxygen transfer efficiency, and periodic pulsations generated from the instability of air jet from nozzle make very small air bubbles. Then, the annular type jet resonator(AJR) applying these two principles successfully was evalulated as the most promising device and also the efficiency showing $20{\sim}30%$ better than conventional diffusers has been verified experimentally.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.1
• /
• pp.116-124
• /
• 2002

The bubble model by Keller and Prosperetti is adapted to solve the nonlinear oscillation of a gas bubble. This formulation leads to accurate results since it introduces the energy equation instead of the polytropic assumption for the bubble interior. The numerical method used in this study is stable enough to handle large amplitude of bubble oscillation. The numerical results show some interesting nonlinear phenomena fur the bubble oscillator. The excitation changes the natural frequency of the bubble and makes some harmonic resonances at $f/f_0=1/2, 1/3$ and so on. The natural frequency of a bubble oscillator decreases compared with the linear case result, which means that the nonlinear bubble oscillation system is a "softening"system. In addition, the frequency response curve jumps up or down at a certain frequency. It is also found that there exist multi-valued regions in the frequency response curve depending on the initial conditions of bubble. The dependency of the bubble motion on the initial condition can generate extremely large pressure and temperature which might be the cause of the acoustic cavitation and the sonoluminescence.inescence.

• The Journal of the Acoustical Society of Korea
• /
• v.28 no.4
• /
• pp.363-369
• /
• 2009

In this paper, an estimation method is presented to determine the equivalent circuit model of an underwater acoustic piezoelectric transducer with multiple resonant modes. A fitness function that includes the coupled resonant effects is proposed to minimize an error between the measured impedance of the transducer and the calculated impedance of the equivalent model. Unknown parameters of the equivalent circuit are estimated by using PSO algorithm. The proposed method is applied to an example transducer of the sandwich type with 3 resonances in the frequency band of interest. The analytical impedance of the estimated equivalent circuit model is compared with the measured impedance of the transducer and the validity of proposed method is verified.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.9
• /
• pp.599-605
• /
• 2015

The revised U.S. Nuclear Regulatory Commission(NRC), Regulatory Guide(RG) 1.20, rev.3 requires the evaluation of the potential adverse effects from pressure fluctuations and vibrations on piping and components for the reactor coolant, steam, feedwater, and condensate systems. Detailed vibration analyses for the systems attached to the steam generator are very difficult, because these piping systems are very complicated. This paper suggests a screening method for the flow-induced vibration of acoustic resonances and pump-induced vibration of the piping systems attached to the steam generator in order to conduct the APR1400 comprehensive vibration assessment program. This paper seeks to address the areas such as potential vibration sources, and methods to prevent the occurrence of acoustic resonances and pump-induced vibration of piping systems attached to the steam generator, for conducting the APR1400 comprehensive vibration assessment program. The screening method in this paper will be used to estimate the flow-induced vibration of the piping systems attached to the steam generator for the APR1400.