• The Journal of the Acoustical Society of Korea
• /
• v.41 no.4
• /
• pp.397-409
• /
• 2022

A model is developed for the calculation of sea surface generated ambient noise in the range dependent ocean environment. The sources are located in the horizontal plane all around and their depths are at the near-surface. The receiver array is located in the range dependent ocean waveguide. One-way coupled mode method is used to model the acoustic propagation between the sources and receiver in the range dependent waveguide, and the cross spectral density matrix of noise is derived. In simulation, noise intensity, beamforming result and coherence function are calculated from the cross spectral density matrix. These results are compared with those in the range independent environment. The modeling result shows the effect of the vertical directionality and asymmetry characteristics of the horizontal plane.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2023.05a
• /
• pp.209-209
• /
• 2023

본 연구에서는 강우 시 발생하는 음향 및 진동 신호를 기반으로 강우강도를 산정하기 위한 방법론을 제안하였다. 먼저, Raspberry Pi, 콘덴서 마이크 및 가속도 센서로 구성된 관측 기기로부터 실제 비가 내리는 환경에서의 음향 및 진동 신호를 수집하였다. 가속도 센서로부터 계측된 진동 신호를 활용하여 강우 유무에 대한 이진 분류를 수행하고, 강우가 발생한 것으로 판단된 기간에 해당하는 음향 신호에 Short-Time Fourier Transform 기술을 적용하여 주파수 영역에서 나타나는 magnitude의 평균과 표준 편차, 최고 주파수 등의 특징을 기반으로 강우강도를 산정하였다. 이를 위해 앙상블 기반의 머신러닝 학습 모델인 XGBoost 알고리즘을 사용하였으며, 광학 우적계를 통해 관측한 강우강도와 산정 결과를 비교·평가하였다. 강우강도 산정 과정에서 사용된 음향 신호의 길이를 1초, 10초, 1분으로 구분하였으며, 무강우 기간 내 음향 정보로부터 배경 음향에 의한 노이즈를 제거하고자 하였다. 최종적으로 강우 유무 이진 분류 과정의 선행 여부, 음향 신호의 길이 및 노이즈 제거 방법에 따른 강우강도 산정 결과들에 대한 성능 비교를 통해 본 연구에서 제안하고자 하는 방법론의 실효성을 평가하였다.

• Phonetics and Speech Sciences
• /
• v.14 no.4
• /
• pp.67-75
• /
• 2022

This study compared voice range profiles (VRPs) of modal and falsetto register in 53 dysphonic and 53 non-dysphonic adult women with gliding vowel /a/'. The results shows that maximum fundamental frequency (F0_MAX), maximum intensity (I_MAX), F0 range (F0_RANGE), and intensity range (I_RANGE) are lower in the dysphonic group than in the non-dysphonic group. F0_MAX and F0_RANGE are significantly higher in falsetto register than modal register in both groups. I_MAX and I_RANGE are significantly higher in falsetto register in the non-dysphonic group, but those are not different between two registers in the dysphonic group. There was no statistically significant difference in minimum F0 (F0_MIN) and minimum intensity (I_MIN) between the two groups. Modal-falsetto register transition occurred at 378.86 Hz (F4#) in the dysphonic group and 557.79 Hz (C5#) in the non-dysphonic group, which was significantly lower in the dysphonic group. It can be seen that both modal and falsetto registers in dysphonic adult women are reduced compared to non-dysphoinc adult women, indicating that the vocal folds of dysphonic adult women are not easy to vibrate in high pitches. The results of this study would be the basic data for understanding the acoustic features of voice disorders.

• Journal of the Korean Society of Laryngology, Phoniatrics and Logopedics
• /
• v.17 no.2
• /
• pp.89-97
• /
• 2006

The stop consonants in Korean are classified into three types according to the manner of articulation as unaspirated (UA), slightly aspirated (SA) and heavily aspirated (HA) stops. Both the UA and the HA types are always voiceless in any environment. Generally, the voice onset time (VOT) could be measured spectrographically from release of consonant burst to onset of following vowel. The VOT of the UA type is within 20 msec of the burst, and about 40-50 msec in the SA and 50-70 msec in the HA. There have been many efforts to clarify properties that differentiate these manner categories. Umeda, et $al^{1)}$ studied that the fundamental frequency at voice onset after both the UA and HA consonants was higher than that for the SA consonants, and the voice onset times were longest in the HA followed by the SA and UA. Han, et $al^{2)}$ reported in their speech synthesis and perception studies that the SA and UA stops differed primarily in terms of a gradual versus a relatively rapid intensity build-up of the following vowel after the stop release. Lee, et $al^{3)}$ measured both the intraoral and subglottal air pressure that the subglottal pressure was higher for the HA stop than for the other two stops. They also compared the dynamic pattern of the subglottal pressure slope for the three categories and found that the HA stop showed the most rapid increase in subglottal pressure in the time period immediately before the stop release. $Kagaya^{4)}$ reported fiberscopic and acoustic studies of the Korean stops. He mentioned that the UA type may be characterized by a completely adducted state of the vocal folds, stiffened vocal folds and the abrupt decreasing of the stiffness near the voice onset, while the HA type may be characterized by an extensively abducted state of the vocal folds and a heightened subglottal pressure. On the other hand, none of these positive gestures are observed for the SA type. Hong, et $al^{5)}$ studied electromyographic activity of the thyroarytenoid and posterior cricoarytenoid (PCA) muscles during stop production. He reported a marked and early activation of the PCA muscle associated with a steep reactivation of the thyroarytenoid muscle before voice onset in the production of the HA consonants. For the production of the UA consonants, little or no activation of the PCA muscle and earliest and most marked reactivation of the thyroarytenoid muscle were characteristic. For the SA consonants, he reported a more moderate activation of the PCA muscle than for the UA consonant, and the least and the latest reactivation of the thyroarytenoid muscle. Hong, et $al^{6)}$ studied the observation of the vibratory movements of vocal fold edges in terms of laryngeal gestures according to the different types of stop consonants. The movements of vocal fold edges were evaluated using high speed digital images. EGG signals and acoustic waveforms were also evaluated and related to the vibratory movements of vocal fold edges during stop production.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.5
• /
• pp.589-600
• /
• 2019

In order to investigate the flow structures around Geumo archipelago on Southern Waters of Korea, water movements were measured for 25 hours during spring tide in May and neap tide in September 2002 using ADCP (Acoustic Doppler Current Profiler) attached to a running boat. Dominant directions of ebb and flood current at spring tide are SE-NW, representing the average flow rate of approximately 40cm/s in the surface layer. However because of the topographical reason, the direction and speed of the flow in the narrow waterway sea area around the northwest of Gae Island were different. There was no notable baroclinic component of tidal flow at spring tide. This indicates that the sea area has been actively engaged in vertical mixing due to island wake or eddy due to narrow waterways, shallow water depth and rapid flow rate around archipelago. At neap tide, dominant directions of tidal flows are SSE-NNW and the average flow rate in the surface layer is about 85 percent of the spring tide. The duration and intensity of the flow direction are shorter and less dominant than the spring tide. It is expected that asymmetrical tidal mixing will occur due to vertical velocity shear and horizontal eddies. From daily mean tidal flows obtained from the ADCP observation, it was found that the northwest of Gae Island have flows in NW~NE, the west of Geumo Island have the average currents of up to 21 cm/s WSW~SSW and counterclockwise circulation or eddy currents are formed in the west of Sori Island.

• Tunnel and Underground Space
• /
• v.26 no.5
• /
• pp.396-408
• /
• 2016

Rock fracture mechanics has been widely applied to various fields of rock and civil engineering. But most researches covered mode I behavior, though mode II behavior is dominant in rock engineering. Until now, there is only one ISRM suggested method for mode II toughness of rock. A new SCC (Short Core in Compression) mode II toughness test method was developed considering 1) application of confining pressure, 2) easiness of notch creation, 3) utilization of existing equipment, 4) simple test procedure. The stress intensity factors were determined by 3D finite element method considering line and distributed loading conditions. The tests with granite specimens were carried out using MTS 815 rock test system with a loading rate of 0.002 mm/s. The mean value of mode II fracture toughness of granite showed $2.33MPa{\sqrt{m}}$. Mode I toughness of the same granite was $1.12MPa{\sqrt{m}}$, determined by Brazilian disk test and $K_{IIC}/K_{IC}=2.08$. The smooth fracture surface with rock powder formation also supported mode II behavior of SCC method. The SCC method can be used for the determination of mode II fracture toughness of rocks based on the current results.

• Journal of Biomedical Engineering Research
• /
• v.30 no.5
• /
• pp.418-427
• /
• 2009

As many people are westernizing their life style and food consumption habits, a number of patients who have malignant tumors which grow very rapidly and hazardously destroy the human body are increasing. Ultrasonic hyperthermia is not only one of the tumor treatment methods which employs the non-radioactive ultrasonic waves to increase the temperature at the tumor region up to $40\sim45^{\circ}C$ to destroy and suppress tumor cells but also has been proved by many studies. Due to the rapid development of High Intensity Focused Ultrasound(HIFU), the ultrasound hyperthemia extensively boosts its applications in clinical field. For those reasons, Computed simulation factor should be needed before inspection to patients. To prove efficiency of ultrasonic hyperthermia, precise acoustic field measurement considering tissue characteristics and a heating experiment with tissue mimicking material phantom were conducted for effectiveness of simulation program. Finally, in this study, the computer simulation program verified the anticipated temperature effects induced by ultrasound hyperthermia. In the near future, it is hoped that this simulation program could be utilized to improve the efficiency of ultrasound hyperthermia.

• International Journal of Aeronautical and Space Sciences
• /
• v.17 no.4
• /
• pp.518-525
• /
• 2016

This paper presents the characteristics of non-fundamental multi-mode combustion instability and the effects of high-harmonic components on the Rayleigh criterion. Phenomenological observations of multi-harmonic-mode dynamic pressure waves regarding the intensity of harmonic components and the source of wave distortion have been explained by introducing examples of second- and third-order harmonics at various amplitudes. The amplitude and order of the harmonic components distorted the wave shapes, including the peak and the amplitude, of the dynamic pressure and heat release, and consequently the temporal Rayleigh index and its integrals. A cause-and-effect analysis was used to identify the root causes of the phase delay and the amplification of the Rayleigh index. From this analysis, the skewness of the dynamic pressure turned out to be a major source in determining whether multi-mode instability is driving or damping, as well as in optimizing the combustor design, such as the mixing length and the combustor length, to avoid unstable regions. The results can be used to minimize errors in predicting combustion instability in cases of high multi-mode combustion instability. In the future, the amount of research and the number of applications will increase because new fuels, such as fast-burning syngases, are prone to generating multi-mode instabilities.

• Journal of Environmental Science International
• /
• v.16 no.4
• /
• pp.393-397
• /
• 2007

The sonolytic decomposition of NHCs(Nitrogen Heterocyclic Compounds), such as atrazine[6-chloro-N-ethyl-N'-(1-methylethyl)-1,3,5-triazine-2,4-diamine], simazine(6-chloro-N,N'-diethyl-1,3,5-triazine-2,4-diamine), trietazine(6-chloro-N,N,N'-triethyl-1,3, 5-triazine-2,4-diamine), in water was investigated at a ultrasound frequency of 200kHz with an acoustic intensity of 200W under argon and air atmospheres. The concentration of NHCs decreased with irradiation, indicating pseudo-first-order kinetics. The rates were in the range $1.06{\sim}2.07({\times}10^{-2}min^{-1})$ under air and $1.30{\sim}2.59({\times}10^{-2}min^{-1})$ under argon at a concentration of $200{\mu}M$ of NHCs. The rate of hydroxyl radicals(${\bullet}{OH}$) formation from water is $19.8{\mu}M\;min^{-1}$ under argon and $14.7{\mu}M\;min^{-1}$ under air in the same sonolysis conditions. The sonolysis of NHCs is effectively inhibited, but not completely, by the addition of t-BuOH(2-methyl-2-propanol), which is known to be an efficient ${\bullet}{OH}$ radical scavenger in aqueous sonolysis. This suggests that the main decomposition of NHCs proceeds via reaction with ${\bullet}{OH}$ radical; a thermal reaction also occurs, although its contribution is small. The addition of appropriate amounts of Fenton's reagent $[Fe^{2+}]$ accelerates the decomposition. This is probably due to the regeneration of ${\bullet}{OH}$ radicals from hydrogen peroxide, which would be formed from recombination of ${\bullet}{OH}$ radicals and which may contribute a little to the decomposition.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.47 no.5
• /
• pp.212-221
• /
• 2010

The bubbles could be created from multiple source in the surface of ocean. The bubbles which are created like this affect to the intensity and the sound speed of acoustic wave which are used from the ocean. From the research, it observed Reverberation from the sea surface, using Vbeam transmission and reception equipment that was a cross-shaped Array, from 2008 July 2nd to July 3rd at 4Km from the East Sea Mookho port. It is difficult to analyze data because the received signal has ambient noise and occurrence ISI(Inter Symbol Interference) for multipath. This paper remove that ambient noise and ISI using the directions of arrival beamforming and the filter and sum beamforming. After beamforming, a following DFE(Decision Feedback Equalizer) removes the remaining multipath components. Experimental results show that the proposed technique reduce the errors caused by ISI.