• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.7
• /
• pp.269-274
• /
• 2013

We are used with the alkaline ion water which an application field does to object for drinking water compare with the alkaline ion water which asked ion acid electrolysis so as to be very different. This is used with sterilization disinfection use by residual chlorine in case of strong acidity according to ph intensity, and in case of middle acidity use by washing and face washing, and mix with meal materials in case of weak acidity widely usable in cooking. Acid ion water generates as we electrolyze water. Chlorine gas and sodium hydroxide etc. was generated at electrolysis process, and we have toward sterilizing power. Derelicts such as chlorine, phosphorus, sulfur etc. are gathered from a negative ion, and we make acid ion water to + electrode direction in electrolysis. We used a diaphragm in order to disconnect too acid water and alkaline water. We implemented so that the acid water which it came down to three kinds of PWM voltage to PWM (pulse width modulation) control, and implementation method of ph intensity change authorized ph intensity between weak acidity to electrode in strong acidity as we used Microprocessor, and intensity was adjusted successively by PWM control was generated.

• KSBB Journal
• /
• v.23 no.4
• /
• pp.335-339
• /
• 2008

Biodiesel is an alternative and renewable energy source, which is hoped to reduce global dependence on petroleum and environmental problem. Biodiesel produced from a variety of oil sources such as vegetable oil, animal fat and waste oils, and has properties similar to those associated with petro-diesel, including cetane number, volumetric heating value, flash point, viscosity and so on. In this study, we investigate the effect of quality of raw materials on alkali-catalyzed transesterification for producing of biodiesel. The increase of content of free fatty acid and water in oil were caused the sharp decrease of conversion yield. Also, the low purity of methanol in reactant was inhibited the reaction rate. In the case of addition of sodium sulfate as absorbent to prepare catalyst solution, the content of fatty acid methyl ester in product was increased more about 1.6% than that of control. However, the addition of zeolite, sodium chloride and sodium sulfate as absorbent in reactant to remove water generated from reaction did not show any enhancement in the reaction yield. This result may provide useful information with regard to the choice and preparation of raw materials for more economic and efficient biodiesel production.

• Journal of the Korean Society of Safety
• /
• v.34 no.3
• /
• pp.42-49
• /
• 2019

This study statistically analyzed the laboratory accidents by investigating 806 laboratory accident survey reports which were officially submitted to government from 2013 to June 2017. After comparing domestic and foreign accident classification criteria, the laboratory accidents were classified using KCD7(Korean Standard Classification of Diseases) and OIICS(Occupational Injury and Illness Classification System) criteria. For the type and part of injury, KCD7 classification criteria was adopted. And, for the cause and occurrence type of accidents, OIICS was adopted to analyze the laboratory accidents. Most of injuries happened to the wrist and hand caused by sharp materials or chemical materials. The analysis of accident cause showed that accidents resulted in medical practice and accidents from handtools and chemical materials such as acid and alkali frequently occurred. The major occurrence types of laboratory accidents was body exposure to the chemical materials such as hydrochloric acid and sulfuric acid. In addition, the accidents resulted in destroy of grasped object or falling object were frequently reported.

• Journal of Microbiology and Biotechnology
• /
• v.20 no.11
• /
• pp.1513-1520
• /
• 2010

A bacterium capable of producing melanin pigment in the presence of L-tyrosine was isolated from a crop field soil sample and identified as Klebsiella sp. GSK based on morphological, biochemical, and 16S rDNA sequencing. The polymerization of this pigment occurs outside the cell wall, which has a granular structure as melanin ghosts. Chemical characterization of the pigment particles showed then to be acid resistant, alkali soluble, and insoluble in most of the organic solvents and water. The pigment got bleached when subjected to the action of oxidants as well as reductants. This pigment was precipitated with $FeCl_3$, ammoniacal silver nitrate, and potassium ferricynide. The pigment showed high absorbance in the UV region and decreased absorbance when shifted towards the visible region. The melanin pigment was further charecterized by FT-IR and EPR spectroscopies. A key enzyme, 4-hydroxyphenylacetic acid hydroxylase, that catalyzes the formation of melanin pigment by hydroxylation of L-tyrosine was detected in this bacterium. Inhibition studies with specific inhibitors, kojic acid and KCN, proved that melanin is synthesized by the DOPA-melanin pathway.

• Textile Coloration and Finishing
• /
• v.19 no.3
• /
• pp.12-17
• /
• 2007

In this study, we have investigated properties and behaviors of the indigo vat dyeings on synthetic fibers, namely PET and PTT/Spandex. In addition, indigo vat dyeing conditions such as dyeing temperature, dye concentration and pH were optimized. The finding results show that higher color strengths of indigo dyeings on the two types of applied fibers were obtained at $110^{\circ}C$ and $90^{\circ}C$, respectively. Furthermore, acid leuco dyeings on the fiber substrates using acetic acid and formic acid show higher dye uptake with compared to alkali leuco counterparts.

• KSBB Journal
• /
• v.24 no.1
• /
• pp.89-95
• /
• 2009

Biodiesel (fatty acid alkyl esters), which is produced from sustainable resources such as vegetable oil, animal fat and waste oils, have used to as substitutes for petro-diesel. In this study, we investigate the performance of 30 L and 300 L pilot-scale biodiesel production system using alkali-catalyst transesterification from soybean oil and rapeseed oil produced at Jeju island in Korea. The 30 L-scale biodiesel production was performed to in the condition of reaction temperature $65^{\circ}C$, catalyst amount 1% (w/w) and oil to methanol molar ratio 1 : 8. At that reaction condition, the fatty acid methyl ester contents of product are above 98% within reaction time 30 min. Also, the conversion yield of over 98% was obtained in 300 L-scale biodiesel production system using rapeseed oil and soybean oil. The quality of biodiesel produced from reaction system was satisfied to recommended quality standard of Korea. Our results may provide useful information with regard to the scale-up of more economic and efficient biodiesel production process.

• Korean Journal of Materials Research
• /
• v.16 no.2
• /
• pp.80-84
• /
• 2006

The removal efficiency of Cu and Fe contaminants on the silicon wafer surface was examined to investigate the effect of cleaning solutions on the behavior of metallic impurities. Silicon wafers were intentionally contaminated with Cu and Fe solutions by spin coating and cleaned in different types of cleaning solutions based on $NH_4OH/H_2O_2/H_2O\;(SC1),\;H_2O_2/HCl/H_2O$ (SC2), and/or HCl/$H_2O$ (m-SC2) mixtures. The concentration of metallic contaminants on the silicon wafer surface before and after cleaning was analyzed by vapor phase decomposition/inductively coupled plasma-mass spectrometry (VPD/ICP-MS). Cu ions were effectively removed both in alkali (SC1) and in acid (SC2) based solutions. When $H_2O_2$ was not added to SC2 solution like m-SC2, the removal efficiency of Cu impurities was decreased drastically. The efficiency of Cu ions in SC1 was not changed by increasing cleaning temperature. Fe ions were soluble only in acid solution like SC2 or m-SC2 solution. The removal efficiencies of Fe ions in acid solutions were enhanced by increasing cleaning temperature. It is found that the behavior of metallic contaminants as Cu and Fe from silicon surfaces in cleaning solutions could be explained in terms of Pourbaix diagram.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.33 no.4
• /
• pp.42-48
• /
• 2001

The spent liquor (BSL) obtained from alkaline sulfite-anthraquinone (AS-AQ) cooking of pine bark was applied as a deinking agent. In the ONP deinking system, although BSL removed the small size of ink particles (${\geq}$$12.5{\mu}m$), it did not improve the brightness of pulp. The brightness of pulp slightly improved when treated with BSL at 150~$180^{\circ}C$. However, the brightness of the pulp was lower than that of a commercial deinking agent (oleic acid). It seems that BSL treated with a high temperature still had a high dispersing ability on the ink particles. Intensive oxidations were introduced, and remarkable deinking effects were observed at 13kgf/$cm^2$ oxygen pressure, $160^{\circ}C$ and 2h. When BSL treated at 13kgf/$cm^2$ oxygen pressure, $170^{\circ}C$ and a time period of 30~90 min is added to the pulp, at 0.1% or lower, the deinking effect became higher than that of oleic acid. On the other hand, additional alkali treatments during the oxidation possibility as a deinking agent when oxidized. However, since the oxidized BSL still has a high dispersing ability and lower molecular weight, several modifications need to be done in the near future in order to be applied as a high quality deinking agent.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.419-419
• /
• 2016

High efficiency silicon solar cell requires the textured front surface to reduce reflectance and to improve the light trapping. In case of mono-crystalline silicon solar cell, wet etching with alkaline solution is widespread. However, the alkali texturing methods are ineffective in case of multi-crystalline silicon wafer due to grain boundary of random crystallographic orientation. The acid texturing method is generally used in multi-crystalline silicon wafer to reduce the surface reflectance. However the acid textured solar cell gives low short-circuit current due to high reflectivity while it improves the open-circuit voltage. To reduce the reflectivity of multi-crystalline silicon wafer, double texturing method with combination of acid and reactive ion etching is an attractive technical solution. In this paper, we have studied to optimize RIE experimental condition with change of RF power (100W, 150W, 200W, 250W, 300W). During experiment, the gas ratio of SF6 and O2 was fixed as 30:10.

• Journal of the Korean Applied Science and Technology
• /
• v.11 no.2
• /
• pp.113-120
• /
• 1994

Amphoteric surfactants were synthesized by the cyclization of 1-(2-hydroxyethyl)-2-undecyl-2-imidazoline [I] with acrylic acid ethyl ester. Compound [I] was easily hydrolyzed with water, especially in the presence of a alkali, to afford amidoamines. After [I] was hydrolyzed, the reaction mixture was allowed to react with acrylic acid ethyl ester and then soapoinfied. Only sodium salts of N- -(2-carboxyethyl)-N'-(2-hydroxyethyl)aminoethyl]dodecanoyl amide[III] was obtained. However, when the reacton of [I] with acrylic acid ethyl ester was carried out in the presence of water, followed by soapnification, ring cleavage of [I] occurred at 2, 3 position, different from hydrolysis of [I] where the cleavage occurred at 1, 2 position, to give sodium salts of N-[N'-(2-carboxyethyl)aminoethyl]-N-(2-hydroxyethyl)dodecanoyl amide [IV] and N-[N', N'-bis(2-carboxyethyl)aminoethyl]-N(2-hydroxyethyl)dodecanoyl amide [V] as main products.