• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.8 no.3
• /
• pp.177-185
• /
• 2014

In this study, the exoskeleton orthosis for the assistance of dorsiflexion torque in ankle joint to prevent foot-drop was developed. It was consist of three part; 1) the power part using artificial pneumatic actuator, 2) wearing part of ankle and knee joints to fix the orthosis, and 3) control part to detect the gait phase using physiological signal. The dorsiflexion torque was generated by the artificial pneumatic actuator connected with wearing part between ankle and knee joint. The accurate timing to assist dorsiflexion torque is made up of physiological signal in foot sole part that detect the gait phase, that is, stance and swing phase in each foot. We conduct the experiment to investigate the effect of exoskeleton orthosis to the 7 elderly people and 10 healthy people. The result showed that the muscular activities in tibialis anterior muscle were reduced because of the assistance of dorsiflexion torque in ankle joint using the exoskeleton orthosis.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.3
• /
• pp.26-36
• /
• 2010

This paper provides a description of the combustion model to obtain an accurate dynamic engine phenomena that satisfies real-time simulation for model-based engine control. The combustion chamber is modeled as a storage device for mass and energy. The combustion process is modeled in terms of a two-zone model for the burned and unburned gas fractions. The mass fraction burnt is modeled in terms of a Wiebe function. The instantaneous net engine torque is calculated from the engine speed and the instantaneous piston work. The modeling accuracy has been tested with a cylinder pressure data on a test bench and also the ability of real-time simulation has been checked. The results show that combustion model yields sufficiently good performance for the model-based control logic design. However the influence factors effected on model accuracy are some room for improvement.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.5
• /
• pp.315-319
• /
• 2016

This paper proposes a simple adaptive sliding mode control algorithm for controlling a permanent magnet synchronous generator (PMSG) of a MW-class direct-driven wind turbine system. The proposed adaptive sliding mode controller does not require accurate knowledge of the PMSG parameter or turbine torque values. The proposed controller can accurately track the reference angular speed computed by the maximum power point tracking(MPPT) algorithm. Finally, this paper gives Matlab/Simulink simulation results to verify the practicality and effectiveness of the proposed adaptive sliding mode controller.

• International Journal of Aeronautical and Space Sciences
• /
• v.8 no.1
• /
• pp.105-114
• /
• 2007

This article presents the details of a designed control moment gyroscope (CMG) with a constant speed momentum wheel and one-axis-gimbal, and its experimental results performed at Korea Aerospace Research Institute. The CMG which is able to produce a torque of lOO mNm per each, is mounted in a pyramid configuration with four SGCMGs. Each CMG test and a single axis maneuver test with four-CMG cluster configuration are performed to confirm their performance on a ground-test facilities consisted of three major parts: a vibration isolation system, a dynamic force plate (Kistler sensor), and a DSP board. These facilities provide the accurate data of three axial and torques from the control moment gyro. Details of the CMG experimental results are presented with discussion of the experimental errors. The experimental data are compared with theoretical results and both results are used to verify their performance specifications.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11a
• /
• pp.219-224
• /
• 2001

An accurate tip position control of a single-link flexible manipulator subjected to torque disturbance is achieved by utilizing so called sliding mode controller with disturbance estimation (SMCDE). After formulating the governing equation of motion in the state 1pace representation, a stable sliding surface is designed via the LQR method. The SMCDE is then synthesized by integrating equivalent sliding mode controller with the disturbance estimator which is featured by an integrated average value of the imposed disturbance over a certain sampling period. The regulating tip motion of the flexible manipulator is evaluated by employing the proposed SMCDE.

• Journal of the Korean Institute of Navigation
• /
• v.21 no.1
• /
• pp.109-118
• /
• 1997

In this paper, applications of multilayer neural networks to control of flexible robot beam are considered. The multilayer nerual networks can be used to approximate any continuous function to a desired degree of accuracy and the weights are updated by Gradient Method. When a flexible beam is rotated by a motor through the fixed end, transverse vibration may occur. The motor torque should be controlled insuch a way that the motor rotates by a specified angle, while simultaneously stabilizing vibration of the flexible manipulators so that is arrested as soon as possbile at the end of rotation. Accurate control of lightweight beam during the large changes in configuration common to robotic tasks requires dynamic models that describe both rigid body motions, as well as the flexural vibrations. Therefore, a linear dynamic state-space model of for a single link flexible robot beam is derived and PD controller, LQP controller, and inverse dynamical neural networks controller are composed. The effectiveness the proposed control system is confirmed by computer simulation.

• Proceedings of the KIEE Conference
• /
• 1997.07f
• /
• pp.2139-2142
• /
• 1997

The most important thing in vector control scheme is the knowledge of accurate electrical motor parameters. These parameters can computed by conventional motor test, such as no-load and locked rotor tests. However, the values from these tests are different from actual motor parameters, and the adjustment process of the parameters is time consuming. This paper presents an auto-tuning method for vector control of induction motor. The tuning algorithm is based on the rotor flux behavior of the induction motor for stepwise torque current command. The transient terminal voltage caused by the undesirable variation of the rotor flux is used for tuning the slip gain $K_5$ defined as the inverse of the rotor time constant. The electrical parameters of induction motor can also calculated by this method. The presented method is evaluated through the computer simulations.

• Proceedings of the KIEE Conference
• /
• 2000.11d
• /
• pp.647-649
• /
• 2000

Brushless DC motors are widely used in many industrial fields as an actuator of robot and driving power motors of electrical vehicle. In this paper adaptive fuzzy sliding mode scheme is developed for velocity control of brushless DC motor. The proposed scheme does not require an accurate dynamic model. yet it guarantees asymptotic trajectory tracking despite torque variations. Numerical simulation and DSP-based experimental works for velocity control of brushless DC motor are carried out.

• Proceedings of the KIEE Conference
• /
• 1993.11a
• /
• pp.100-102
• /
• 1993

This paper proposes a control method of induction machine at a low speed range. When an encoder is used for speed detection, we usually obtain speed information from the increased pulse number. At low speed range, however, we can get only average speed between encoder pulses and it makes speed controller unstable. By using a disturbance observer and torque current, it is possible to estimate accurate speed information. The simulation and experiment show that the stable speed control is performed at a low speed with proposed algorithm.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.4
• /
• pp.123-129
• /
• 2001

Recent requirements for the fast and accurate motion in industrial robot manipulators need more advanced control tech-niques. To satisfy the requirements, importance of force control is being continuously increased and the expensive force sensor is usually installed to obtain the contact force information in practice. This information is indispensable for the force control of maintaining the desired contact force. However, the sensor cost is too high to be used in industrial applications. In this paper, it is proposed to estimated the contact force occurring between the end-effector of 2 DOF robots and environ-ment. The contact force estimation system is developed based on the static and dynamic models of 2 DOF robot manipula-tors. where the contact force is described with respect to the link torque. The Extended Kalman Filter is designed and its performance is verified in simulations.