• The Journal of Korea Robotics Society
• /
• v.12 no.3
• /
• pp.279-286
• /
• 2017

In this paper, we proposed a method to determine the acceleration/deceleration time of the motion for reducing the residual vibration caused by the resonance of the robot in the high-speed motion. The relationship between the acceleration/deceleration time and the residual vibration was discussed for the trapezoidal velocity profile by analyzing the time when the jerk happens. The natural frequency of the robot can be estimated in advance through the dynamics simulation. The simulation and experiment for both cases where the moving distance of the robot is long enough and the distance is short, are implemented in the 1-DOF linear robot. Simulation and experimental results show that when the acceleration/deceleration time is a multiple of the vibration period, the settling time and the amplitude of the residual vibration become less than when the time is not a multiple.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.16 no.1
• /
• pp.89-94
• /
• 2013

Electro Otical Tracking System(EOTS) is required for a rapid movement as well as the stabilization of Line-Of-Sight(LOS). In order to achieve these two goals, this paper presents a position and velocity driving profile generation method from the constant acceleration and deceleration profile according to the current state, enabling a fast and smooth trajectory even if the target position changes during the movement of LOS. Simulation and experimental results reveal that the settling time could be reduced significantly by adopting the present position control scheme.

• Proceedings of the KIEE Conference
• /
• 2007.10a
• /
• pp.299-300
• /
• 2007

In this paper, slip wear phenomenon of train was studied by traction force of acceleration and braking force of deceleration. First, the slip wear phenomenon on train operation mode was analyzed when powering, coasting and braking each and then rail wear was analyzed from the slip wear data. Especially, the data proved correlation between slip wear and deceleration rather than acceleration. Second, If velocity of a train is constant, even though the velocity is high, ATO logging data and measurement data proved that the rail wear is not serious. It will help for efficient braking force operation providing fundamental data to braking step control.

• The Bulletin of The Korean Astronomical Society
• /
• v.43 no.1
• /
• pp.54.3-54.3
• /
• 2018

In this study, we perform a statistical investigation on the kinematic classication of 4264 coronal mass ejections (CMEs) from 1996 to 2015 observed by SOHO/LASCO C3. Using the constant acceleration model, we classify these CMEs into three groups; deceleration, constant velocity, and acceleration motion. For this, we devise four dierent classication methods by acceleration, fractional speed variation, height contribution, and visual inspection. Our major results are as follows. First, the fractions of three groups depend on the method used. Second, about half of the events belong to the groups of acceleration and deceleration. Third, the fractions of three motion groups as a function of CME speed classied by the last three methods are consistent with one another. Fourth, according to the last three methods, the fraction of acceleration motion decreases as CME speed increases, while the fractions of other motions increase with speed. In addition, the acceleration motions are dominant in low speed CMEs whereas the constant velocity motions are dominant in high speed CMEs.

• Journal of The Korean Astronomical Society
• /
• v.55 no.3
• /
• pp.67-74
• /
• 2022

In this study, we perform a statistical investigation of the kinematic classification of 4,264 coronal mass ejections (CMEs) from 1996 to 2015 observed by SOHO/LASCO C3. Using the constant acceleration model, we classify these CMEs into three groups: deceleration, constant velocity, and acceleration motion. For this, we devise three different classification methods using fractional speed variation, height contribution, and visual inspection. The main results of this study can be summarized as follows. First, the fractions of three groups depend on the method used. Second, about half of the events belong to the groups of acceleration and deceleration. Third, the fractions of three motion groups as a function of CME speed are consistent with one another. Fourth, the fraction of acceleration motion decreases as CME speed increases, while the fractions of other motions increase with speed. In addition, the acceleration motions are dominant in low speed CMEs whereas the constant velocity motions are dominant in high speed CMEs.

• International Journal of Highway Engineering
• /
• v.9 no.4
• /
• pp.215-226
• /
• 2007

To verify the performance of roadside barriers, occupant risk indices are calculated from acceleration and angular velocity data of vehicle crash tests. The occupant risk indices to be computed include THIV(Theoretical Head Impact Velocity), PHD(Post-impact Head Deceleration), ASI(Acceleration Severity Index), OIV(Occupant Impact Velocity) and ORA(Occupant Ridedown Acceleration). There is a confusion due to different values of occupant risk indices produced for the same test data because various computational procedures and data processing methods can be applied to compute them. To slove this problem the effects of various numerical procedures and data processing methods on occupant risk indices were investigated. If the sampling rate specified in the guidelines is used for full-scale vehicle crash tests, an interpolation of impact time and numerical integration methods do not result in an appreciable change of THIV and OIV. The way to determine 10msec moving average for PHD and zero offset of data processing should be specified in the guidelines because 10msec moving average and zero offset methods have a significant influence on occupant risk indices.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.6
• /
• pp.395-402
• /
• 2000

This paper presents the improvement for speed characteristics of a Brushless DC Motor (BLDCM), it was applied to digital PI control for this. The practical PID control has been widely used to velocity control of DC motors. In this paper, a digital PI controller is used in order to decrease the speed error in constant velocity control of BLDCM. A TMS320C31 DSP is used for the microprocessor of digital PI control. The method using the DSP carry out the real-time control. The DSP has the rapid calculation ability and sampling time used lms. Driving BLDCM used 50W, motor input DC 150V and rotation speed 3000rpm. When BLDCM is to approval for discretion velocity at the acceleration and deceleration driving with any load, it was a feasible for stabilization control. Therefore, the experimental results indicate the superiority and validity of the velocity control by digital PI control.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.5
• /
• pp.852-858
• /
• 2013

In numerical control (NC) machining, a machining error in equipment generally occurs for a variety of reasons. If there is a change in direction in the NC code, the characteristics of the automatic acceleration or deceleration function cause an overlap of each axis of the acceleration and deceleration zones, which in turn causes a shift in the actual processing path. Many studies have been conducted for error calibration of the edge as caused by automatic acceleration or deceleration in NC machining. This paper describes a geometric interpretation of the shape and processing characteristics of the operating NC device. The paper then describes a way to determine a feedrate that achieves the desired tolerance by using linear and parabolic profiles. Experiments were conducted by the validate equations using a three-axis NC machine. The results show that the machining errors were smaller than the machine resolution. The results also clearly demonstrate that the NC machine with the developed system can successfully predict machining errors induced with a change in direction.

• Korean Journal of Applied Biomechanics
• /
• v.17 no.3
• /
• pp.69-80
• /
• 2007

The purpose of this study was to investigate the difference of ground reaction forces of swimming athletes during their starting motion and to find out the most effective starting motions which were used in swimming athletes. The subjects were 9 male and 8 female high school swimming athletes who were athletic career over 7 years and used three starting motions in competition. The ground reaction forces were measured from each athletes performing three starting motion each of the open grap starting motion, closed grap starting motion and track starting motion. For the measurement, the force platform of AMTI company was utilized, and the analysis on measured ground reaction forces were used of Biosoft(Ver. 1.0). The items measured were stance time, Fz max deceleration force and Fz max deceleration force time, Fz mid stance force and Fz mid stance force time, Fz max acceleration force and Fz max acceleration force time, Torque maximum and Torque maximum time, Torque average, Excursion along Y axis of center of pressure of foot, Excursion along X axis of center of pressure of foot, Length of center of pressure of foot, Average velocity of center of pressure of foot. The data measured by the closed grap starting motion, open grap starting motion and track starting motion were analyzed by one-way repeated ANOVA. The results were as follows ; 1. The Fz max deceleration force time, Fz mid stance force, Fz max acceleration force, Torque maximum and Torque maximum time, Excursion along Y axis of center of pressure of foot, Average velocity of center of pressure of foot were significantly fast and large in the closed grap starting motion then open grap starting motion and track starting motion. 2. The Excursion along Y axis of center of pressure of foot was significantly long in the closed grap starting motion then open grap starting motion and track starting motion.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.5
• /
• pp.313-319
• /
• 2016

It is very important to understand and control the sloshing in a liquid container that is partially filled with liquid. Previous studies focused primarily on the sloshing and resonance caused by sinusoidal excitations, while the present study focuses on understanding and suppressing sloshing in a container that moves rapidly from a given point to another in industrial applications. To achieve this, we first numerically predict the two-phase flow induced by the horizontal movement of a rectangular container. Then we analyze the effects of container-velocity profile (in particular acceleration/deceleration duration) on sloshing. Results show that sloshing is significantly suppressed when the acceleration/deceleration duration is a multiple of the 1st-mode natural period of sloshing.