• Journal of Life Science
• /
• v.13 no.1
• /
• pp.9-14
• /
• 2003

Seed germinability might be highly related to seedling establishment. The experiments were carried out to evaluate the effect of presowing treatments of aging, priming, $GA_3$ , prechilling and water imbibition, different temperatures and light quality during germination on germination of gourd (Lagenaria siceraria Standl.) seeds. Aging treatment with different temperatures and periods was done by the accelerated aging method. Priming using KNO$_3$ and $GA_3$ treatment for 24 hours were done at 100 mM and at 0.01 mM before a week prechilling. The germination tests using a week prechilled seeds were done at 10, 20 and $30^{\circ}C$ on the condition of darkness, and also with blue, red, far-red light and darkness as light quality treatments. FR-yongjadaemok and FR-kunghap were used as test cultivars and their daily germination rates were measured at treatment levels. Germination rates were reduced in the seeds aged at $45^{\circ}C$ for 6 days. Prechilling showed the highest and fastest rate among the four presowing treatments but the two other presowing treatments had similar or less rates than water imbibition. Prechilling done before sowing enhanced the low vigor seeds, and accelerated the germination of cv. FR-kunghap at 20 to $30^{\circ}C$ and with blue, red light or darkness during germination although far-red light inhibited their germination.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.4
• /
• pp.19-26
• /
• 2010

We found that saturated water vapor pressure is the most dominant stress factor for the degradation phenomenon in the package for high-power phosphor-converted white light emitting diode (high power LED). Also, we proved that saturated water vapor pressure is effective acceleration stress of LED package degradation from an acceleration life test. Test conditions were $121^{\circ}C$, 100% R.H., and max. 168 h storage with and without 350 mA. The accelerating tests in both conditions cause optical power loss, reduction of spectrum intensity, device leakage current, and thermal resistance in the package. Also, dark brown color and pore induced by hygro-mechanical stress partially contribute to the degradation of LED package. From these results, we have known that the saturated water vapor pressure stress is adequate as the acceleration stress for shortening life test time of LED packages.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.27 no.1
• /
• pp.7-12
• /
• 1994

The kinetics of browning reaction of dried shrimp powder samples were investigated during storage. The temperature conditions of the ding process were $25^{\circ}C\;and\;45^{\circ}C$, and the samples were stored at water activity ($a_w$) of 0.33, 0.44, 0.52, 0.65 and temperatures of $35^{\circ}C,\;45^{\circ}C,\;55^{\circ}C$ and temperature fluctuations between $33^{\circ}C\;and\;55^{\circ}C$. When the shrimp was dried at $25^{\circ}C$ the activation energies obtained from the Arrhenius plot ranged from 13.57 to 14.33 kcal/mol. From these energies of activation, the $Q_{10}$ values at $25^{\circ}C$ showed 1.93 to 2.00. In the case of drying at $45^{\circ}C$ the activation energies were $13.12{\sim}13.61\;kcal/mol$ and $Q_{10}$ values were $1.89{\sim}1.93$, respectively. In addition, a storage study under square-wave fluctuating temperature conditions was carried out by varying the shrimp sample temperature between $35^{\circ}C\;and\;55^{\circ}C$ within 7 days regular fluctuation cycle. The data obtained from the fluctuating temperature storage study will be used in the prediction of shelf-lives. The shelf-lives assessed at $25^{\circ}C$ from the accelerated shelf-life tests ranged from 4 days at aw 0.65 to 139 days at aw 0.33.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.11 no.3
• /
• pp.21-27
• /
• 1982

A kinetical approach for the non-enzymatic browning reaction of the dried file-fish was studied. The reaction rates revealed a tend to increase with increasing water activity and showed the maximum at $0.75\;a_w$ The activation energies obtained from the Arrhenius plot ranged 12.5 to 16.5 Kcal/mole. From these energies of activation, the $Q_{10}$ values at $45^{\circ}C$ showed 1.9 to 2.3 and both activation energy and $Q_{10}$ values were reduced with increase in $a_w$ Shelf-lives, the time to reach an 0.15 O.D./g solid at which severe brown color change could be de ectable, decreased rapidly as the temperature and water activity increase. A storage study under a square-wave fluctuating temperature condition (at 35 and $55^{\circ}C$ periodically with 7 days interval), the rate constants at all water activities used in the experiments were higher than those at $45^{\circ}C$, the mean temperature of the cycle which affects other kinetic parameters including activation energies, $Q_{10}$ values and finally the shelf-lives. The data obtained from the fluctuating temperaure storage study will be used in prediction of shelf-life. The shelf lives assessed at $25^{\circ}C$ from the accelerated shelf-life tests ranged from 179 daysat $0.75\;a_w$ to 302 days at $0.44\;a_w$.

• Progress in Medical Physics
• /
• v.25 no.4
• /
• pp.205-209
• /
• 2014

Medical polymers require sterilization and must be able to maintain material properties for a specified shelf life. Sterilization can be achieved by using gamma or e-beam exposure. In this study, accelerated aging tests of poly(ether-block-amide) (PEBA) copolymer samples is presented. PEBA copolymer samples with different polyether content that result in Shore hardness of 35D to 72D, were sterilized using e-beam radiation followed by accelerated aging at $55^{\circ}C$. E-beam sterilization effect on molecular weight and mechanical property has performed and analyzed. The average molecular weight significantly reduced as a result of ageing. The enlarged proportion of low molecular weight chains in the aged samples is consistent with the generation of degradation products produced by oxidative chain scission. Also E-beam materials have shown decreased tensile strength and elongation. Overall, this study demonstrated that the medical grade PEBA was significantly affected by radiation exposure over aging time, particularly at high irradiation doses. For medical use in case of radiation sterilization required, it is recommended to avoid Pebax material. If Pebax material must be in use for medical device, recommend to use alternate sterilization method such as Ethylene Oxide sterilization.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.5
• /
• pp.1686-1693
• /
• 2014

In this paper, oil-paper samples composed of transformer windings were used to investigate the insulation degradation process subjected to partial discharge (PD), with artificial defects inside to simulate the PD induced insulation degradation. To determine appropriate test voltages, the breakdown time obtained through a group of accelerated electrical degradation tests under high voltages was firstly fitted by two-parameter Weibull model to acquire the average breakdown time, which was then applied to establish the inverse power law life model to choose advisable test voltages. During the electrical degradation process, PD signals were synchronously detected by an ultra-high frequency (UHF) sensor from inception to breakdown. For PD analysis, the whole degradation process was divided into ten stages, and chaos theory was introduced to analyze the variation of three chaotic parameters with the development of electrical degradation, namely the largest Lyapunov exponent, correlation dimension and Komogorov entropy of PD amplitude time series. It is shown that deterministic chaos of PD is confirmed during the oil-paper degradation process, and the obtained results provide a new effective tool for the diagnosis of degradation of oil-paper insulation subjected to PD.

• Food Science of Animal Resources
• /
• v.26 no.4
• /
• pp.471-477
• /
• 2006

This study was conducted to evaluate the application of high dose irradiation for ensuring shelf stability of marinated and precooked pork rib steak in the severe environments such as desert or space, etc. Marinated and precooked pork rib steak was manufactured, vacuum-packaged and gamma-irradiated with the absorbed doses of 10, 20, 30, 40 and 50 kGy, and used for the tests of the growth of microorganisms and lipid oxidation during storage at 35t of acceleration condition. Any growth of microorganisms was not observed in irradiated samples after irradiation immediately. However, the growths were observed in 10, 20 and 30 kGy samples at 4, 7 and 14 day storage, respectively. High dose (40 and 50 kGy) gamma irradiation retarded the growth of aerobic microorganisms by the analysis of kinetic parameter. The content of malondialdehyde increased in all samples during storage periods, and gamma irradiation accelerated the increase of lipid oxidation. Therefore, the application of combination of the various food processing technology should be considered for the sterilization of marinated and precooked pork rib steak without any deterioration of the quality occurred by high dose irradiation.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2003.10a
• /
• pp.134-135
• /
• 2003

The dental implant materials required good mechanical properties, such as fatigue strength, combined with a high resistance to corrosion. For increasing fatigue resistance and delaying onset of stress corrosion cracking, shot peening has been used for > 50 years to extend service life of metal components. However, there is no information on the electrochemical behavior of shot peened and hydroxyapatite(HA) coated Ti-6Al-4V alloys. To increase fatigue strength, good corrosion resistance, and biocompatibility, the electrochemical characteristics of Ti/TiN/HA coated and shot peened Ti-6Al-4V alloys by electron beam physical vapor deposition(EB-PVD) have been researched by various electrochemical method in 0.9%NaCl. Ti-6Al-4V alloys were prepared under the condition of hydrogen and vacuum arc furnace. The produced materials were quenched at 1000$^{\circ}C$ under high purity dried Ar atmosphere and were hold at 500$^{\circ}C$ for 2 hrs to achieve the fatigue strength(1140㎫) of materials. Ti-6Al-4V alloys were prepared under the condition of hydrogen and vacuum arc furnace. Shot peening(SP) and sand blasting treatment was carried out for 1, 5, and 10min. On the surface of Ti-6Al-4V alloys using the steel balls of 0.5mm and alumina sand of 40$\mu\textrm{m}$ size. Ti/TiN/HA multilayer coatings were carried out by using electron-beam deposition method(EB-PVD) as shown Fig. 1. Bulk Ti, powder TiN and hydroxyapatite were used as the source of the deposition materials. Electrons were accelerated by high voltage of 4.2kV with 80 - 120mA on the deposition materials at 350$^{\circ}C$ in 2.0 X 10-6 torr vacuum. Ti/TiN/HA multilayer coated surfaces and layers were investigated by SEM and XRD. A saturated calomel electrode as a reference electrode, and high density carbon electrode as a counter electrode, were set according to ASTM GS-87. The potentials were controlled at a scan rate of 100 mV/min. by a potentiostat (EG&G Co.273A) connected to a computer system. Electrochemical tests were used to investigate the electrochemical characteristics of Ti/TiN/HA coated and shot peened materials in 0.9% NaCl solution at 36.5$^{\circ}C$. After each electrochemical measurement, the corrosion surface of each sample was investigated by SEM.

• Journal of the Korean Society for Precision Engineering
• /
• v.3 no.2
• /
• pp.62-75
• /
• 1986

An experimental investigation of the machining characteristics such as cutt- ing resistance, surface roughness and tool wear in turning the test pieces of SM45C steel with both coated and uncoated carbide tool tips under various cutting conditions was conducted. Also a specially designed simple vibration damping device was experimentally evaluated for its effectiveness on machined surface roughness and a vibration test was conducted to confirm its ability to reduce the amplitude. Based on these tests finding, the following conclusions are made; 1. The cutting resistance($\textrm{p}_{1}$) increases as the depth of cut(d) increases at fixed feed rate(f) over the cutting speed(v) range of 43-226 m/min and p decreses about 18% average when V is increased for fixed d and f. At V= 226m/min, $\textrm{p}_{1}$/for A, C tips are about the same level but $\textrm{p}_{1}$ for B tip is 15% less than A, C tips. 2. The specific cutting resistance(Ks) at V=226 m/min was derived for A, B, C tips respectively and the value of Ks for B rip is about 20% less than A, C tips. 3. The surface roughness(Ra) improves significantly as the cutting speed(V) is increased and this effect was greater when V>100 m/min. On the other hand, Ra deteriorates as the feed rate(f) is increased and this trend was accelerated when f>0.3 mm/rev. With regard to the difference of Ra values among A, B, C tips, at V=226m/min, d=0.4mm, and f=0.31-0.61mm/rev, Ra values for B.C tips are about 17% less than tip A. 4. The experimental tool wear equations were derived for A, B, C tips and from these equations, the tool life($\textrm{T}_{\textrm{L}}$) baced on the I.S.O. criteria was calculated to be $\textrm{T}_{\textrm{L}}$<$\textrm{T}_{\textrm{LB}}$<$\textrm{T}_{\textrm{LC}}$ for both flank wear($\textrm{V}_{\textrm{B}}$) and boundary wear($\textrm{V}_{\textrm{N}}$). Hence, the coated tips are superior to the uncoated tip and tip C is considered to be the best. 5. The cutting resistance may be slightly reduced and the surface rounghness improved when the damper is used especially when V>100 m/min. Therefore this damping device is considered to be effective and practical. The experimental surface roughness equations were also derived. Based on the vibration test, it is established that the surface roughness improvement was the result of amplitude reduction made possible by the damper.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.10
• /
• pp.117-124
• /
• 2019

Military Vehicles of the Korean army had been developed before 2004 and used manual transmissions. Manual transmissions contain a clutch system regulating the force from engine to transmission. In this study, a 2.5-ton military vehicle's clutch system was investigated. The existing clutch system had the characteristics that need to adjust the clearance between the clutch cover and release bearing. Improper clearance led to early wear of the clutch disk and failure of the clutch cover. To solve these problems, an improved clutch system was suggested and tested. The improved clutch system contains auto adjustment of the clearance and an enhanced clutch disk. To verify the improved clutch systems, 2 stage tests were conducted: an accelerated life test of the clutch system, and a driving test by trainee of driving more than 3,000km. As a result, the problems caused by the improper clearance adjustment were solved and this design was verified.