• Journal of the Korean Ceramic Society
• /
• v.41 no.3
• /
• pp.221-228
• /
• 2004

Basic properties of artificial lightweight aggregate by using waste dusts and strength properties of LWA concrete were studied. Bulk specific gravity and water absorption of artificial lightweight aggregates varied from 1.4 to 1.7 and 13 to 16%, respectively. Crushing ratio of artificial lightweight aggregate was above 10% higher than that of crushed stone or gravel. As a result of TCLP leaching test, the leaching amount of tested heavy metal element was below the leaching standard of hazardous material. Slump, compressive strength and stress-strain properties of LWA concrete made of artificial lightweight aggregate were tested. Concrete samples derived from LWA substitution ratio of 30 vol% and W/C ratio of 45 wt% showed the best properties overall. Thermal insulation and sound insulation characteristics of light weight concrete panel with the optimum concrete proportion were tested. Average overall heat transmission of 3.293W/㎡$^{\circ}C$ was observed. It was higher by about 15% than those of normal concrete made by crushed stone. Sound transmission loss of 50.9 ㏈ in frequency of 500 ㎐ was observed. It was higher by about 13% than standard transmission loss.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.39 no.2
• /
• pp.287-293
• /
• 2010

Regarding the physical properties of wheat flour added with lily's root powder, elasticity in farinograms tended to increase as the ratio of added lily's root powder increased. However, viscoelasticity, absorptivity, absorption time, and stability tended to decrease after an initial increase when a certain ratio of lily's root powder was added to the wheat flour. Results from the rapid viscosity analyzer (RVA) indicated that the retention strength, final viscosity, break down, set back value, $P_{max}$ value of the alveogram, and falling number value decreased. As for gaseous release, measured with a rheofermentometer, the total amount of $CO_2$ gas generated and retained tended to decrease. As for the gelatinizing properties in terms of differences in the granularity and the amount of lily's root powder (bulbs) added to wheat flour, the initial gelatinization temperature had no effect regardless of the type or amount of general grinding and minute (ultra-fine, $10\;{\mu}m$) lily's root powder. Meanwhile, the peak viscosity and peak viscosity time exhibited significant differences in 3, 5% general grinding lily's root powder additive groups. On the other hand, there was no significant difference between 3, 5% minute lily's root powder additive groups. This is likely because the activity of the enzyme in wheat flour decreased relatively and differences in the lily's root powder granularity resulted in a variation in water absorptivity. In the preference test, flavor retention of the functional bread increased according to the granularity of lily's root powder and the ratio of added lily's root powder, thus resulting in significant differences in the mouth feel and flavor; the texture and crumb color, however, did not exhibit significant differences.

• Asian-Australasian Journal of Animal Sciences
• /
• v.14 no.9
• /
• pp.1276-1281
• /
• 2001

The feeding values of four indigenous Kenyan sorghum cultivars and the effects of polyvinylpyrrolidone (PVP) on the utilization of high tannin sorghum by broiler chicks were studied in two 3-week feeding trials. In Experiment 1, one hundred and five broiler chicks (initial average weight 97 g) were randomly assigned to each one of the seven grain-soybean meal diets. The diets consisted of maize [diet 1; no assayable tannin], white sorghum [diet 2; 0.59% catechin equivalents (CE)], cream sorghum [diet 3; 0.94% CE], light brown sorghum [diet 4; 2.71% CE] and dark brown sorghum [diet 5; 3.54% CE]. Diets 6 and 7 were included to test the possibility of overcoming the detrimental effects of sorghum tannins by adding PVP at 0.25% and 0.5% to dark brown sorghum, which resulted in dietary tannin levels of 3.46% and 3.38% CE respectively. In Experiment 2, the effects of tannin on dry matter digestibility (DMD) and nitrogen (N) retention were studied in a 3-week substitution assay in which high tannin sorghum (5% CE) was substituted for white maize at different inclusion levels. Ninety broiler chicks aged 7 days (initial average weight 102 g) were randomly assigned to each one of the six diets. The diets consisted of corn gluten meal and fishmeal as protein sources plus maize [diet 1] and high tannin sorghum at different inclusion levels [diets 2, 3, 4, 5 and 6], resulting in dietary tannin levels of 0, 1.25%, 1.66%, 2.08%, 2.5% and 3.2% CE respectively. Feed intake, feed efficiency and body weight gain were measured weekly. In Experiment 2, tannin absorption, DMD and N retention were measured on days 19, 20 and 21. The results of Experiment 1 showed that feed intake, feed efficiency and body weight gain were all affected by treatment (p<0.05). Diets 1, 2 and 3 gave similar body weight gains and all were better than diets 4 and 5 (i.e. 504, 517, 473 g, vs. 256, 267 g). Similarly, feed efficiencies were higher (p<0.05) for diets 1, 2 and 3 compared to diets 4 and 5 (0.4, 0.42, 0.39 vs. 0.21, 0.23). When 0.25% PVP was added to the dark brown sorghum (diet 6) there was no significant improvement in chick performance (p>0.05). However, addition of 0.5% PVP (diet 7) resulted in significant improvement (p<0.05) in body weight gain compared to the untreated dark brown sorghum. Overall, PVP did not completely overcome the deleterious effects of tannins. The results of Experiment 2 indicate that sorghum inclusion level and subsequent tannin level had no effect on feed intake, feed efficiency, weight gain, DMD and N retention. The above results suggest that tannin level should be limited to below 2.71% CE in broiler chick diets containing 20% CP and 0.4% methionine. However, in diets with 23% CP and 0.8% methionine tannin level of up to 3.2% will not affect performance. Consequently high tannin sorghum (5% CE) can be used to substitute for white maize by up to 100% in broiler chick diets.

• Journal of the Korean Applied Science and Technology
• /
• v.30 no.2
• /
• pp.280-289
• /
• 2013

Various vehicles have been studied in order to protect skin ageing and sustain constantly moisturization. Recently, in relation to maintain of moisture, absorption and penetration of active materials, there has been introducing many preparing methods such as liposome, liquid crystal and multilamellar emulsion. We developed multilayer lamellar vesicle using cetearyl alcohol/ceteth-20 phosphate/dicetyl phosphate as analogy of phospholipid according to variation of shear rate and pH. These multilayer lamellar vesicles were confirmed by cross polarizing microscope. As results, morphologies of lamellar vesicle were not uniformed at low shear rate and pH. Also, stabilities for encapsulation of retinol were observed at $42^{\circ}C$ during two months. As a result, quantitative content of retinol decreased at low pH. Multilayer lamellar vesicle decreased 14% of transepidermal water loss compared with O/W emulsion. We compared multilayer lamellar sun cream to O/W sun cream using in vitro SPF test of water resistance and concluded that multilayer lamellar sun cream is similar to O/W sun cream in water resistance.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.44 no.12
• /
• pp.1819-1825
• /
• 2015

This study was carried out to investigate the effect of hydrocolloids [hydroxypropylmethyl cellulose (HPMC), xanthan gum (XG), guar gum (GG), and glucomannan (GM)] on the physicochemical properties of bread flour dough containing rice flour. In amylograph analysis, the significantly lowest gelatinization temperature was obtained in dough with XG (P<0.05). XG revealed the highest maximum viscosity while GM revealed the lowest. In viscograph test, the lowest gelatinization temperature and maximum viscosity showed the same result as in the amylograph. Breakdown value was also highest in dough containing XG, but lowest in the control and dough containing HPMC. Setback value was highest in dough containing HPMC, but lowest in dough containing XG. In farinograph analysis, consistency was greatest in dough with HPMC and XG. Hydrocolloids affected water absorption, which was highest in dough containing GM. Development times of dough containing HPMC and XG were low. Stability was lowest in dough with XG. Degree of softening was reduced in dough containing HPMC and GG compared to the control but increased in dough containing XG and GM. Dough containing HPMC and GG showed the largest volume at 3 h of fermentation. Dough with HPMC showed the lowest pH value. Hydrocolloids in this study affected physicochemical properties of dough.

• Polymer(Korea)
• /
• v.25 no.1
• /
• pp.98-107
• /
• 2001

Dielectric properties and shape memory characteristics of SBS composites filled with carbon black as conductive filler and (Ba,Ca)$(Sn,Ti)O_3$ or $SrTiO_3$ as dielectrics were investigated for the development of phantom model. SBS/carbon black composite showed an increment of complex dielectric constant with increasing the content of carbon black and the frequency dependence that the dielectric constant decreases with the frequency. The complex dielectric constant and the conductivity of SBS/carbon black/dielectrics composites increased with the increase of dielectrics and the characteristics of the frequency dependence also occurred by the effect of carbon black. Phantom materials with the dielectric properties and the conductivity corresponding to human tissues for the measurement of specific absorption rate(SAR) within the frequency range of current mobile phones(775MHz~2GHz) could be developed by adjusting the composition ratios of carbon black, dielectrics and SBS and by controlling the characteristic of frequency dependence of composite. From thermomechanical cycling test good shape recoverability could be obtained in SBS composite even though the residual strain was increased by the effect of filler.

• Korean Journal of Food Science and Technology
• /
• v.25 no.5
• /
• pp.546-551
• /
• 1993

Rice flour obtained by four different milling methods, Pin mill. Colloid mill, Micro mill, and Jet mill, were used to investigate physico-chemical properties and product. Crude fat, ash, and protein contents of rice flours between different milling methods were similar. Blue value, amylose content, and damaged starch which related to properties of rice flour were reduced in the order that of Jet mill, Micro mill, Colloid mill, and Pin mill. Water absorption index, water solubility index, and water retention capacity increased as damaged starch increased. Hardness of gel(15%) is the highest value for Pin mill. The finer granules (Jet mill) had lower gelatinization onset(To) and peak(Tp) than any other rice flours. Those result are simillar with amylogram properties. Enthalpy of gelatinization increased as damaged starch increased. Jet mill had the highest score (p<0.05) of overall test in sensory evaluation and good paste properties.

• Korean Journal of Food Science and Technology
• /
• v.16 no.4
• /
• pp.429-436
• /
• 1984

To expand the utility of barley the experiments on the extrusion characteristics of barley flour for snack processing were carried out and the effects of the extrusion conditions on the quality of the extrudates were investigated. The optimum moisture content of barley flour for snack processing was 20%. The moisture content and the density of the extrudates decreased with increasing extrusion temperature and decreasing die size. The die swell ranged from 0.98 to 2.18 according to various extrusion conditions and decreased with increasing temperature above $150^{\circ}C$. The lightness, redness and yellowness increased at higher temperature. The water absorption index and the water solubility index showed their maximum values at $180^{\circ}C$.The gelatinization degree of the extrudates increased with increasing temperature. The fracture fore, Young's modulus and maximum fiber stress decreased, but the deformation to fracture increased, with increasing temperature and decreasing die size. The yield force in puncture test showed lower values at higher temperature. The size and the fraction of the air cells increased with increasing temperature and decreasing die size. The optimum extrusion conditions of barley for snack processing were at the temperature of $180^{\circ}C$, with the die size of 4.5mm when processed at 160 rpm.

• Korean Journal of Plant Tissue Culture
• /
• v.24 no.6
• /
• pp.361-367
• /
• 1997

This study was carried out to select cadmium resistant cell lines from leaf-derived calli of diploid and haploid of Nicotiana tabacum cv. BY4, for understanding adaptation mechanism of plants in cadmium contaminated environment. suspended cell clumps were plated onto selection medium containing 0 to 2,000 $\mu$M cadmium. Cadmium resistant colonies were formed on the selection medium after 3 or 4 weeks of culture. The minimum inhibition concentration (MIC) of cadmium on colony formation were 300 $\mu$M in diploid and 200 $\mu$M in haploid plants, respectively. In order to test the resistance to cadmium, selected cell line on MIC were transferred to medium containing high concentration of cadmium. The selected cell lines, especially haploid cell line, were resistant an the high concentration of cadmium. And dry weight, ash weight, and cadmium contents of cell were increased. These results indicated that the selected cell lines showed higher resistance of cadmium than control cells, and haploid plant is more resistant than diploid plant on medium with cadmium.

• Journal of Chest Surgery
• /
• v.44 no.2
• /
• pp.99-107
• /
• 2011

Background: Calcification is the most frequent cause of clinical failure of bioprosthetic tissues fabricated from GA-fixed porcine valves or bovine pericardium. A multi-factorial approach using different mechanisms was recently developed to reduce the calcification of bioprosthetic tissues. The purpose of the present study was to evaluate the synchronized synergism of using L-arginine and $NaBH_4$, compared with ethanol and L-lysine, in glutaraldehyde treated porcine pericardium from the standpoint of calcification and tissue elasticity. Materials and Methods: Porcine pericardium was fixed at 0.625% GA (7 days at room temperature after 2 days at $4^{\circ}C$). An interim step of ethanol (80%; 1 day at room temperature) or L-lysine (0.1 M; 2 days at $37^{\circ}C$) or L-arginine (0.1 M; 2 days at $37^{\circ}C$) was followed by completion of the GA fixation. A final step of NaBH4 (0.1 M; 2 days at room temperature) was followed. Their tensile strength, thickness, and thermal stability were measured. Treated pericardia were implanted subcutaneously into three-week-old Sprague-Dawley rats for 8 weeks. Calcium content was assessed by atomic absorption spectroscopy and histology. Results: L-arginine and $NaBH_4$ pretreatment ($1.81{\pm}0.39$ kgf/5 mm p=0.001, $0.30{\pm}0.08$ mm p<0.001) significantly increased tensile strength and thickness compared with the control ($0.53{\pm}0.34$ kgf/5 mm, $0.10{\pm}0.02$ mm). In a thermal stability test, L-arginine and $NaBH_4$ pretreatment ($84.25{\pm}1.12^{\circ}C$, p=0.023) caused a significant difference from the control ($86.25{\pm}0.00^{\circ}C$). L-lysine and $NaBH_4$ pretreatment ($183.8{\pm}42.6$ ug/mg, p=0.804), and L-arginine and $NaBH_4$ pretreatment ($163.3{\pm}27.5$ ug/mg, p=0.621) did not significantly inhibit calcification compared to the control ($175.5{\pm}45.3$ ug/mg), but ethanol and $NaBH_4$ pretreatment did ($38.5{\pm}37.3$ ug/mg, p=0.003). Conclusion: The combined pretreatment using L-arginine and $NaBH_4$ after GA fixation seemed to increase the tensile strength and thickness of porcine pericardium, fixed with GA. Additionally, it seemed to keep thermal stability. However it could not decrease the calcification of porcine pericardium fixed with GA. $NaBH_4$ pretreatment seemed to decrease the calcification of porcine pericardium fixed with GA, but only with ethanol.