• Journal of Biosystems Engineering
• /
• v.22 no.3
• /
• pp.279-288
• /
• 1997

This study was worked out to obtain fundamental data needed for developing a continuous type dryer. The drying process in a cross-flow type continuous dryer was expressed as partial differential equations, and a drying simulation model for predicting rice moisture content, rice temperature, drying air absolute humidity, drying air temperature was developed by using the finite difference method. To validate the performance of the drying simulation model, a prototype continuous dryer was constructed in this study. The size of the test dryer was one-tenth to that of a commercial continuous dryer. The difference in the outlet rice moisture content between the predicted values and the measured values was within 0.5%, that of outlet rice temperature was below $3^{\circ}C$, that of drying air temperature in drying bed was within $8^{\circ}C$ and that of relative humidity of outlet drying air was big because of the different measuring point. In addition, a drying simulation model for a actual size continuous dryer with double flow was developed in this study. This drying simulation model included the rice mixing effect in the middle of drying length. The difference of outlet moisture content between the predicted and the measured values showed below 0.5% in this study.

• Journal of the Korean Society of Safety
• /
• v.21 no.3 s.75
• /
• pp.45-52
• /
• 2006

The AITs(autoignition temperatures) describe the minimum temperature to which a substance must be heated, without the application of a flame or spark, which will cause that substance to ignite. The AITs are often used as a factor in determining the upper temperature limit for processing operations and conditions for handling, storage and transportation, and in determining potential fire hazard from accidental contact with hot surfaces. The measurement AITs are dependent upon many factors, namely initial temperature, pressure, volume, fuel/air stoichiometry, catalyst material, concentration of vapor, time lag. Therefore, the AITs reported by different ignition conditions are sometimes significantly different. This study measured the AITs of benzene, toluene and xylene isomers from time lag using AS1M E659-78 apparatus. The experimental ignition delay times were a good agreement with the calculated ignition delay times by the proposed equations wtih a few A.A.D.(average absolute deviation). Also The experimental AITs of benzene, toluene, o-xylene, m-xylene and p-xylene were $583^{\circ}C,\;547^{\circ}C,\;480^{\circ}C,\;587^{\circ}C,\;and\;557^{\circ}C$, respectively.

• Atmosphere
• /
• v.21 no.4
• /
• pp.361-371
• /
• 2011

In this study, characteristics and trends of tropical night (TN) are investigated by using the KMA 14 observation data for the recent 50 years (1958-2007) over South Korea. The TN is defined as a day with a daily minimum temperature exceeds the absolute threshold temperature ($25^{\circ}C$), and the relative deviation from normal temperature, 95th percentile of all observed daily minimum temperature. Although the spatial distribution of TN occurrence depends on the choice of the definitions, the frequency of TN shows strong spatial and interannual variations with the minimum at high land area (Chupungnyeong and wet years) and maximum at southern coastal area and large city area (Jeju, Busan, Seoul, Daegu). Most of TN occurs in August (56%) and July (41%), and the duration date of TN is proportional to the frequency of TN without regard to the definition method. In general, increasing trends are found in the TN time series without regard to the analysis method, but the trends are clearly depending on the analysis period and geographic locations. Decreasing trends are prominent during the most of analysis period, especially until the mid of 1990, whereas strong increasing trends are found during recent 30 years (1988-2007), especially at Jeju, Ulsan, Daegu and Pohang. Also the severity of TN is significantly increased in recent years.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.7 no.3
• /
• pp.146-152
• /
• 1987

Sorghum cv. Pioneer 93 1, sorghum-sudangrass hybrid cv. Sioux and maize plant cv. Blizzard were assayed for toxic concentrations of nitrate-nitrogen ($NO_3$-N) and their relationship to morphological characteristics and environmental temperature in a field and phytotron trial. In the phytotron, sorghum and maize plants ranging from emergence to heading stage, were grown under different day/night temperatures of 30125, 25/20,28/18 and 1818 degree C. Nitrate-nitrogen in sorghum and maize plants was accumulated mainly in stems. Therefore nitrate concentration in the young plants was increased as development of stalks advanced and was highest at the stage of 3-4 leaves, when the plants had a leaf weight ratio 0.78-0.80 g/g plant weight. However, nitrate concentrations of the plant decreased as morphological development progressed, especially from the stage of growing point differentiation. Correlation coefficients showed a positive correlation of nitrate concentration with leaf weight ratio, leaf area ratio and specific leaf area, while plant height, dry matter percentage and absolute growth rate showed a negative association with TEX>$NO_3$-N ($P{\le}0.1$%). Cyanogenic glycosides, total nitrogen and crude protein were close associated with nitrate accumulation, and positively significant ($P{\le}0.1$%). High temperature over 30/25^{\circ}C.$ for 3 weeks increased N-uptake and dry matter accumulation, but reduced nitrate concentration. Under cold temperature below 18/8^{\circ}C.$ concentration of nitrate-N was increased in spite of its limited nitrogen uptake and plant growth.

• Fire Science and Engineering
• /
• v.26 no.3
• /
• pp.85-90
• /
• 2012

The autoignition temperature (AIT) of a material is the lowest temperature at which the material will spontaneously ignite. The AIT is important index for the safe handling of flammable liquids which constitute the solvent mixtures. This study measured the AITs of n-Decane+sec-Butanol system by using ASTM E659 apparatus. The AITs of n-Decane and sec-Butanol which constituted binary system were $212^{\circ}C$ and $447^{\circ}C$, respectively. The experimental AITs of n-Decane+sec-Butanol system were a good agreement with the calculated AITs by the proposed equations with a few A.A.D. (average absolute deviation).

• Journal of Biosystems Engineering
• /
• v.37 no.6
• /
• pp.429-433
• /
• 2012

Purpose: While rapeseed oil, soy bean oil, palm oil and waste cooking oil are being used for biodiesel, the viscosity of them should be lowered for fuel. The most widely used method of decreasing the viscosity of vegetable oil is to convert the vegetable oil into fatty acid methyl ester but is too expensive. This experiment uses ultrasonic energy, instead of converting the vegetable oil into fatty acid methyl ester, to lower the viscosity of the waste cooking oil. Methods: For irradiation treatment, the sample in a beaker was irradiated with ultrasonic energy and the viscosity and temperature were measured with a viscometer. For heating treatment, the sample in a beaker was heated and the viscosity and temperature were measured with a viscometer. Kinematic viscosity was calculated by dividing absolute viscosity with density. Results: The kinematic viscosity of waste cooking oil and cooking oil are up to ten times as high as that of light oil at room temperature. However, the difference of two types of oil decreased by four times as the temperature increased over $83^{\circ}C$. When the viscosity by the treatment of ultrasonic energy irradiation was compared to one by the heating treatment to the waste cooking oil, the viscosity by the treatment of ultrasonic energy irradiation was lower by maximum of 22% and minimum of 12%, than one by the heating treatment. Conclusions: Ultrasonic energy irradiation lowered the viscosity more than the heating treatment did, and ultrasonic energy irradiation has an enormous effect on fuel reforming.

• Archives of Pharmacal Research
• /
• v.28 no.2
• /
• pp.220-226
• /
• 2005

Temperature and medium composition were changed with the aim of increasing growth and erythropoietin (EPO) production in EPO-producing Chinese hamster ovary (CHO) cells. We used the CHO cell line, IBE, and its derivative, CO5, which over-expresses the first two enzymes of the urea cycle, carbamoyl phosphate synthetase I (CPS I) and ornithine transcar-bamoylase (OTC). When supplements were added to the medium at $33\;^{\circ}C$, the growth of IBE and CO5 cells increased by $27\%\;and;26\%$, respectively and the maximum yield of EPO was increased by $40\%$ in both cell lines. The absolute EPO concentration in the CO5 cells was always $55{\sim}60\%$ higher than in the IBE cells. In addition, when the two cell lines were continuously cultured with supplements at $33\;^{\circ}C$ until their growth rates approached those at $37\;^{\circ}C$, the growth rates of both IBE and CO5 cells increased by $54\%$ and their maximum EPO levels increased by up to $73\%\;and\;56\%$, respectively. Therefore, the growth and EPO expression levels of CO5 cells increased 2.2-fold and 2.6-fold, respectively, compared to those of the IBE cells. These results indicate that adaptation to lower temperature as well as medium supplementation could be important for improving cell growth and EPO production.

• Journal of the Korean Chemical Society
• /
• v.6 no.1
• /
• pp.47-53
• /
• 1962

The "reactivity" of coal is one of the important characteristics of a coal used as a process raw material as well as a fuel. In this study, the reactivity was measured in terms of the magnitude of the reaction rate constant in the reduction of carbon dioxide with coal. A reactivity-testing apparatus was designed and constructed, and its performance characteristics were investigated by using Korean anthracite and hard-wood charcoal. Experiments were carried out at temperatures ranging from 750 to 1100$^{\circ}C$ with pulverized Korean anthracite whose sizes range from 1 to 10mm in diameter. Results showed that the reaction rate constant was not appreciably affected by the particle size investigated, and the reactivities of the anthracite and the charcoal were found to be a function of reaction temperature alone. It was also found that a straight line was produced when the logarithm of the rate constant is plotted against the reciprocal of the absolute temperature. The reactivities of the charcoal were found to be 2 to 10 times higher than those of the anthracite at a temperature ranging from 750 to 1100$^{\circ}C$, and 90% of carbon dioxide was reduced to carbon monoxide by the anthracite at a temperature above 1050$^{\circ}C$.

• Korean Journal of Optics and Photonics
• /
• v.16 no.4
• /
• pp.319-325
• /
• 2005

A signal processing method for white light interferometry (WLI), which performs a series of analog signal processing steps to locate the central interference fringe position at high speed: is developed and applied to a WLI temperature sensor system. We found that the new method has random walk of $0.019^{\circ}C/\sqrt{Hz}$ with good linearity. However, the temperature change in the path-matching interferometer results in drift of the measured sensor output. The temperature dependence of drift in the WLI temperature sensor system, was calculated to be $1.42{\mu}m/^{\circ}C$. It is also found that the relationship between the peak spacing in the interferogram and the spacing measured by the method can be nonlinear when the fringe spacing is comparable to the coherence length of the source.

• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.916-919
• /
• 2003

In this paper, we deal with a development of measurement system to apply the leakage rates test of primary containment in nuclear power plant. The measurement test about leakage rates in primary containment is one sort of test to prove safety of nuclear power plant. The parameters which are measured to calculate leakage rates are drybulb temperature, dew point temperature(or relative humidity), absolute pressure and flow. Overall, the measurement system consists of sensor module for data acquisition of the parameters, transfer module for wireless data communication and control module to control system and to calculate leakage rates. Because existing measurement systems are difficult to set in field, we pursued convenience of use, we applied wireless data communication and individual form module using battery. We also changed for the better in confidence. Recently, we are developing a drybulb temperature and a dew point temperature sensor module. We describe about function of developed measurement system, its standard and an plan for verification of measurement system.