• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1476-1481
• /
• 2003

Kinematic calibration enhances absolute accuracy by compensating for the fabrication tolerances and installation errors. Effectiveness of calibration procedures depends greatly on the measurements performed. This paper investigates identifiable parameters and optimum postures for four different calibration procedures - measuring postures completely with inverse kinematic residuals, measuring postures completely with forward kinematics residuals, measuring only the three position components, and restraining the mobility of the end-effector using a constraint link. The study is performed for a six degree-of-freedom fully parallel HexaSlide type parallel manipulator, HSM. Results verify that all parameters are identifiable with complete posture measurements. For the case of position measurements, one and for the case of constraint link, three parameters were found non-identifiable. Selecting postures for measurement is also an important issue for efficient calibration procedure. Typically, the condition number of the identification Jacobian is minimized to find optimum postures. Optimal postures showed the same trend of orienting themselves on the boundaries of the search space.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제49권8호
• /
• pp.451-458
• /
• 2000

The precise speed and position control technique for Brushless DC Motor demands accurate position and speed feedback information. Generally, resolver or absolute encoders are used as speed and positiion sensor. But they increase cost and more problem happens at low speed than high speed specially. Therefore, in this paper, optimal speed observer is proposed for decreasing size and cost of whole system. And also, we consider the error problem about the system modeling and measurement at low speed range as well as high speed. The overall system consists of two parts, a drive and a speed observer. We make use of Least square curve fitting algorithm as speed observer and can overcome low resolution by proposed observer. Also, because of using the signal of hall sensor, robust control is possible in low speed as well as high speed for the change of the parameters of the system and disturbance. To construct observer using the signal of hall sensor, we design the pulse multiplier circuit and the software of microprocessor, AT89CC2051. Finally, the performance of the proposed observer is exemplified by some simulations and experiments.

• 한국광학회지
• /
• 제16권4호
• /
• pp.319-325
• /
• 2005

고속으로 간섭피크의 위치를 찾기 위해 일련의 아날로그 신호처리를 수행하는 백색광간섭(WLI)센서용 신호처리 방식을 고안하고, 이를 WLI 온도센서 시스템에 적용하였다. 새로운 신호처리방식을 적용한 결과 잡음은 $0.019^{\circ}C/\sqrt{Hz}$로 측정되었으며, 선형성도 우수하였다. 그러나 보상용 간섭계에서의 온도변화가 센서출력의 드리프트로 나타났으며, 현재의 구성에서 드리프트의 온도 의존성은 $1.42{\mu}m/^{\circ}C$인 것으로 계산되었다. 또한 간섭피크간 간격이 광원의 가간섭길이에 비해 충분히 넓지 않은 경우 간섭무늬 피크의 간격과 신호처리기가 측정한 피크 간격과의 관계가 비선형적으로 나타날 수 있음도 확인하였다.

• 한국자동차공학회논문집
• /
• 제13권3호
• /
• pp.87-95
• /
• 2005

Most of the motorcycle engines have used carburetors in the fuel system, because of its simple structure and reliability but the fuel economy and the emissions of those engines are bad when we compared with automobile engines .To meet with the tighten emission regulations and the higher requirements for fuel economy, the application of the carburetor on the motorcycle engines would be limited. Therefore, it is important to develope a ECU control system for motorcycle engines. Since the fuel injection system is expensive, it is necessary to decrease the cost of ECU system for motorcycle engines, but the accuracy of the ECU control system should be increased as high as possible. In this paper, we studied about the AFS characteristics of motorcycle engine controled by indirect method.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.1615-1620
• /
• 2003

Kinematic calibration is a process whereby the actual values of geometric parameters are estimated so as to minimize the error in absolute positioning. Measuring all components of Cartesian posture, particularly the orientation, can be difficult. With partial pose measurements, all parameters may not be identifiable. This paper proposes a new device that can identify all kinematic parameters with partial pose measurements. Study is performed for a six degree-of-freedom fully parallel Hexa Slide manipulator. The device, however, is general and can be used for other parallel manipulators. The proposed device consists of a link with U joints on both sides and is equipped with a rotary sensor and a biaxial inclinometer. When attached between the base and the mobile platform, the device restricts the end-effector's motion to five degree-of-freedom and can measure position of the end-effector and one of its rotations. Numerical analyses of the identification Jacobian reveal that all parameters are identifiable. Computer simulations show that the identification is robust for the errors in the initial guess and the measurement noise. Intrinsic inaccuracies of the device can significantly deteriorate the calibration results. A measurement procedure is proposed and formulations of cost functions are discussed to prevent propagation of the inaccuracies to the calibration results.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1494-1499
• /
• 2003

Kinematic calibration is a process whereby the actual values of geometric parameters are estimated so as to minimize the error in absolute positioning. Measuring all components of Cartesian posture, particularly the orientation, can be difficult. With partial pose measurements, all parameters may not be identifiable. This paper proposes a new device that can be used to identify all kinematic parameters with partial pose measurements. Study is performed for a six degree-of-freedom fully parallel Hexa Slide manipulator. The device, however, is general and can be used for other parallel manipulators. The proposed device consists of a link with U joints on both sides and is equipped with a rotary sensor and a biaxial inclinometer. When attached between the base and the mobile platform, the device restricts the end-effector's motion to five degree-of-freedom and can measure position of the end-effector and one of its rotations. Numerical analyses of the identification Jacobian reveal that all parameters are identifiable. Computer simulations show that the identification is robust for the errors in the initial guess and the measurement noise.

• 한국의학물리학회지:의학물리
• /
• 제29권2호
• /
• pp.66-72
• /
• 2018

The proper position of a multi-leaf collimator (MLC) is essential for the quality of intensity-modulated radiation therapy (IMRT) and volumetric modulated arc radiotherapy (VMAT) dose delivery. Task Group (TG) 142 provides a quality assurance (QA) procedure for MLC position. Our study investigated the QA validation of the mechanical leaf gap measurement and the maintenance procedure. Two $VitalBeam^{TM}$ systems were evaluated to validate the acceptance of an MLC position. The dosimetric leaf gaps (DLGs) were measured for 6 MV, 6 MVFFF, 10 MV, and 15 MV photon beams. A solid water phantom was irradiated using $10{\times}10cm^2$ field size at source-to-surface distance (SSD) of 90 cm and depth of 10 cm. The portal dose image prediction (PDIP) calculation was implemented on a treatment planning system (TPS) called $Eclipse^{TM}$. A total of 20 VMAT plans were used to confirm the accuracy of dose distribution measured by an electronic portal imaging device (EPID) and those predicted by VMAT plans. The measured leaf gaps were 0.30 mm and 0.35 mm for VitalBeam 1 and 2, respectively. The DLG values decreased by an average of 6.9% and 5.9% after mechanical MLC adjustment. Although the passing rates increased slightly, by 1.5% (relative) and 1.2% (absolute) in arc 1, the average passing rates were still within the good dose delivery level (>95%). Our study shows the existence of a mechanical leaf gap error caused by a degenerated MLC motor. This can be recovered by reinitialization of MLC position on the machine control panel. Consequently, the QA procedure should be performed regularly to protect the MLC system.

• International Journal of Aeronautical and Space Sciences
• /
• 제16권4호
• /
• pp.581-589
• /
• 2015

This paper describes a monocular vision-based formation flight technology using two fixed wing unmanned aerial vehicles. To measuring relative position and attitude of a leader aircraft, a monocular camera installed in the front of the follower aircraft captures an image of the leader, and position and attitude are measured from the image using the KLT feature point tracker and POSIT algorithm. To verify the feasibility of this vision processing algorithm, a field test was performed using two light sports aircraft, and our experimental results show that the proposed monocular vision-based measurement algorithm is feasible. Performance verification for the proposed formation flight technology was carried out using the X-Plane flight simulator. The formation flight simulation system consists of two PCs playing the role of leader and follower. When the leader flies by the command of user, the follower aircraft tracks the leader by designed guidance and a PI control law, and all the information about leader was measured using monocular vision. This simulation shows that guidance using relative attitude information tracks the leader aircraft better than not using attitude information. This simulation shows absolute average errors for the relative position as follows: X-axis: 2.88 m, Y-axis: 2.09 m, and Z-axis: 0.44 m.

• 재활복지공학회논문지
• /
• 제9권2호
• /
• pp.129-135
• /
• 2015

본 연구에서는 3차원 영상처리와 노팅험 스케일을 이용하여 안면마비 평가 시스템을 개발하였다. 시스템은 측정부, 영상처리부, 연산부, 그리고 안면마비 평가 및 출력부로 구성되어 있다. 두 개의 웹캠을 사용하여 안면부의 8곳에 부착된 마커의 3차원 위치를 계산하였으며, 이를 이용하여 노팅험 스케일을 계산하고 화면에 보여준다. 피험자의 자세변화와 측정방식이 노팅험 스케일에 미치는 영향을 조사하였다. 측정방식은 2차원과 3차원을 비교하였으며, 피험자자세는 정면응시와 $11^{\circ}$ 측면응시를 비교하였다. 측면응시한 피험자를 2차원 방식으로 측정한 경우의 오차가 가장 컸다. 3차원 측정방식이 피험자의 자세변화에 따른 오차에 가장 덜 민감하였다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1992년도 한국자동제어학술회의논문집(국제학술편); KOEX, Seoul; 19-21 Oct. 1992
• /
• pp.382-387
• /
• 1992

In order to obtain desired arc welding performance, we already developed an arc welding robot system that enabled coordinated motions of dual arm robots. In this system one robot arm holds a welding target as a positioning device, and the other robot moves the welding torch. Concerning to such a dual arm robot system, the positioning accuracy of robots is one important problem, since nowadays conventional industrial robots unfortunately don't have enough absolute accuracy in position. In order to cope with this problem, our robot system employed teaching playback method, where absolute error are compensated by the operator's visual feedback. Due to this system, an ideal arc welding considering the posture of the welding target and the directions of the gravity has become possible. Another problem still remains, while we developed an original teaching method of the dual arm robots with coordinated motions. The problem is that manual teaching tasks are still tedious since they need fine movements with intensive attentions. Therefore, we developed a 3-dimensional vision guided robot control method for our welding robot system with coordinated motions. In this paper we show our 3-dimensional vision sensor to guide our arc welding robot system with coordinated motions. A sensing device is compactly designed and is mounted on the tip of the arc welding robot. The sensor detects the 3-dimensional shape of groove on the target work which needs to be weld. And the welding robot is controlled to trace the grooves with accuracy. The principle of the 3-dimensional measurement is depend on the slit-ray projection method. In order to realize a slit-ray projection method, two laser slit-ray projectors and one CCD TV camera are compactly mounted. Tactful image processing enabled 3-dimensional data processing without suffering from disturbance lights. The 3-dimensional information of the target groove is combined with the rough teaching data they are given by the operator in advance. Therefore, the teaching tasks are simplified